Sears 247.88852 owner manual Push, NOTE Use care to avoid pinching the control cable, Drive Belt

Page 22

PUSH

Hex

Nut,

Washer

Align studs for reassembly

Figure 25

•Standing in the operating position, lift up on the handles and pull the frame assembly rearward. The frame and the housing will separate, and the rear auger belt will come off the pulley. Maintain control of the frame assembly while pulling it.

•Remove the two belts from the two engine pulleys. For location of the pulleys, see Figure 26.

Auger

Belt

Drive

Belt

Rear

Engine

Pulley

Idler Pulley

Front Engine

Pulley

Figure 26

•To remove the front auger drive belt, push the idler pulley to the left. The belt brake should move outward. See Figure 27. Lift the front auger drive belt from the front auger pulley.

Push auger

idler pulley

Figure 27

•Place new belts on the two auger pulleys making sure that the front auger belt is under the belt brake. Route belts under and to the left of the flat idler pulley. Hold the belts upward in this position.

•While lifting up on the handles, bring the frame assembly close to the auger housing, and place the two belts on the front and rear engine pulleys. See Figure 28.

PUSH

PUSH

Auger

Housing

Frame Assembly

Figure 28

•Level the frame assembly and tip the auger housing forward to align studs with the corresponding holes on both sides of the frame assembly. See Figure 25 . Push the frame assembly fully on to the studs.

NOTE: Use care to avoid pinching the control cable.

•From the frame assembly side, insert six lock washers and hex nuts on to the studs . These pieces of hardware were removed earlier. See Figure 25. Tighten the nuts securely.

•Reinstall the belt cover onfront of the engine with the two self-tapping screws and flat washers.

•Reattach the chute crank to the chute assembly with the hairpin clip and flat washer.

NOTE: Make sure that the auger cable is routed in front of the belt.

Drive Belt

•Check drive belt every 50 hours of operation for wear and tear.

•Drain the gasoline from the snow thrower, or place a piece of plastic under the gas cap.

•Remove the plastic belt cover on the front of the engine by removing the two self-tapping screws.

•Tip the snow thrower up and forward, so that it rests on the housing.

•Remove six self-tapping screws from frame cover underneath the snow thrower. See Figure 29.

22

Image 22

Contents 247.888520 Owner’s ManualSnow Thrower 9 Horse Power 26” Two-Stage Wheel DrivePRODUCT SPECIFICATIONS TABLE OF CONTENTSWARRANTY INFORMATION ContentTRAINING SAFE OPERATION PRACTICESSAFETY PREPARATIONMAINTENANCE AND STORAGE YOUR RESPONSIBILITYHARDWARE PACK Removing From Carton ASSEMBLYAttaching Handle Assembly Loose PartsAttaching Chute ASSEMBLYAttaching Chute Crank Crank Bracket Attaching Clutch CablesLower Chute Hex Lock NutAttaching Shift Rod Attaching Turn TriggersTrigger Cable Lamp WiringFinal Adjustments Auger ControlSkid Shoe Skid Shoe Remove these hardware to adjust skid shoeTire Pressure Pneumatic Tires Meets ANSI Safety Standards OPERATIONKnowing Your Snow Thrower To Stop The Snow Thrower Safety Ignition SwitchOperating Controls Before Starting EngineA. Electric Starter To Start EngineStarting Instructions at a glance PushWarm Start Operating Snow ThrowerTo Throw Snow B. Recoil StarterTo avoid possible freeze-up of the starter, follow Operating TipsBefore Stopping Recoil StarterGeneral Recommendations MAINTENANCEMAINTENANCE Customer ResponsibilitiesViscosity Chart Engine MaintenanceFigure 19 Lubrication Chart LubricationChanging Oil Spark PlugChute Assembly SERVICE & ADJUSTMENTSAdjustments Traction Drive ClutchCarburetor ServiceADJUSTMENTS AugersNOTE Make sure that the auger cable is routed in front of the belt PUSHNOTE Use care to avoid pinching the control cable Drive BeltChanging Friction Wheel Rubber CoverCarburetor Note If you placed plastic under the gas cap, be certain to remove itPreparing Snow Thrower OFF-SEASON STORAGEPreparing Engine STORAGEPossible Causes TROUBLE-SHOOTINGTrouble Corrective ActionBelt Shave Plate ACCESSORIESSpark Plug REPAIR PARTS SEARS CRAFTSMAN 9.0 H.P. SNOW THROWER MODELPARTS LIST Drive Clutch Cable routed below axle and hooked here SEARS CRAFTSMAN 9.0 H.P. SNOW THROWER MODEL NOTE For painted parts, please refer to the list of Handle Support Bracket L.H. 5/8 Includes references 58 throughHex B-Tapp Screw # 10-16 x Handle Support Bracket R.H. 5/8SEARS CRAFTSMAN 9.0 H.P. SNOW THROWER MODEL SEARS CRAFTSMAN 9.0 H.P. SNOW THROWER MODEL Page Snow Thrower Model Craftsman Engine Model No. 143.999005 for CraftsmanTable continued on next page Recoil Starter CARBURETOR Page Page Page 7084-659-800 1 semana la a días 7 pm, 7 a am 7 de Llame domicilio, a entrega con piezas ordenar Paradomicilio, a reparación de servicio pedir Para 5811-676-800 1 semana la a días 7 día, al horas 24 Llamecorrectora Accion DE LOCALIZACION DE TABLAProblema posible Causasmotor del Preparación TEMPORAIENALMNADECNieve de Expulsor del Preparación usa si carburador el drene No .carburador al llegue34 Figura colocadohaberlo de gasolina, de tapa la de debajo colocado 33 Figurala simétricamente ensamblar importante Es NOTA apropiadofuncionamiento un para fricción de rueda la en goma 32 Figuracontrol propulsora Correacorrea la de frente al encaminado esté de cable el apretar evitar para precavido Sea NOTA23 Figura Service25 Figura 24 FiguraCanaleta La De Conjunto AJUSTES & SERVICEAjustes 21 Figuracomercial Motor del Mantenimiento20 Figura solvente un con lavando y alambre de cepillocliente del Responsabilidades MANTENIMIENCambios De Mecanismo LubricacionArranque de Abreviadas Instrucciones Ruedas La De PresionOperacion De Consejos operación su con familiarizarseMotor El Apagar Como sin cambios de palanca la mueva NUNCA NOTAPropulsor El Enganchar Para 18 Figuraeléctrico Arrancador Motor Del ArranqueAceite Y Gasolina De Llenado Nieve De Expulsor Del DetencionNieve De Expulsor Su Conozca OPERACIONCambios De Palanca Gatillo Del PalancaAjustes de sección la a refiérase detalles, más Para NOTA 16 FiguraDeslizante Zapata la de Ajuste desconectada está bujía la que asegurarseLámpara la de Cableado transmisión la de cambiosFinales Ajustes 15 FiguraGiro De Gatillos Los De Fijacion Cambios De Vara La De Fijaciony velocidad sexta de posición la de fuera cambios Embrague Del Cables Los De Fijacion7 Figura 9 Figura8 Figura 6 Figura3 Figura Canaleta La De FijacionCanaleta La De Manivela La De Fijacion 4 FiguraRequeridas Herramientas ENSAMBLADOMango Del Conjunto Del Fijacion Sueltas PiezasFERRETERIA DE FERRETERIA DE CONJUNTO tiempos dos de Aceite NIEVE DE EXPULSOR DEL ACCESORIOSBujía raspadora Barra gasolina de Recipiénte CorreaSears nieve de expulsor su de segura operación PREPARACION OPERACION DE SEGURAS PRACTICASOPERACION ENTRENAMIENTOCONTENIDO DE TABLA INFORMACIÓN DE GARANTIAProducto Del Especificaciones USA 60179 IL Estates, Hoffman ,.Co And Roebuck Sears Propietario Del ManualFUERZA DE CABALLOS NIEVE DE EXPULSOR 888520.247 Modelo De .No