Sears 247.88852 owner manual Attaching Chute Crank, Assembly

Page 7
Attaching Chute

•Secure bottom hole in the handle to the snow thrower using 5/16 x0.75" hex bolt and lock washer from the hardware pack (group A on page 5 ). Do not tighten at this time. See Figure 2.

Lock Washer &

Hex Bolt (1-3/4”)

Right Handle

Handle

Lock Washer &

Hex Bolt (3/4”)

Tab

Figure 2

•Place a handle tab, included in the hardware pack (group A on page 5), over the upper hole in handle so that the contour of the handle tab matches that of the handle. See Figure 2.

•Secure handle tab to the snow thrower using hex bolt (5/16 x 1.75" long) and lock washer from the same group in the hardware pack. Do not tighten at this time.

•Attach the left handle in the same manner. Do not tighten at this time.

•Place the handle panel in position between the handles so the ends of the curved part of the handles go through the slots in the handle panel. While placing the handle panel, make sure to route chute and chute cable between the handles underneath the panel keeping the cable on top of the engine. Align the holes in the handle with the holes on two sides of the handle panel. See Figure 3.

Right Handle

 

Hex Bolt

Handle Panel

and Flange

 

Nut

 

Align Holes

Carriage Bolt,

Cupped Washer

and Hex Nut

Figure 3

•Attach the handle panel to the handle with two carriage bolts, cupped washers (cupped side against the handle panel) and hex nuts on each side. See Figure 3. You will find these fasteners in the hardware pack (group B on page 5). Align the contour of the carriage bolt head with the handle.

Attaching Chute

•Place the chute assembly over the chute opening with the chute facing front of the unit.

NOTE: Make sure that the chute cables are straightened while assembling the chute.

•Place the chute flange keeper (flat side down) beneath lip of chute assembly as shown in Figure 4.You will find the chute flange keepers in group E of the hardware pack.

•Insert 1/4-20 hex bolt and flange nut from group E up through chute flange keeper and chute assembly as shown in Figure 4. Do not tighten at this time. Rotate chute to install all the flange keepers.

Chute

Hex

Flange

Nut

Chute

Flange

Hex Keeper

Bolt

Figure 4

•After assembling all three chute flange keepers, tighten, then back off 1/4 turn to allow easier movement of the chute. Use (2) 7/16" wrenches.

Attaching Chute Crank

•On the left side of the handle panel, place the upper chute crank bracket on to the inside of the handle panel support. See Figure 5. You will find this bracket and associated hardware in group F of hardware pack.

•Insert hex bolt through the upper chute crank bracket, handle panel support, and upper left handle. Secure the bracket using cupped washer and hex nut. Make sure that the cupped side of the washer is set against the handle.

ASSEMBLY

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents 9 Horse Power 26” Two-Stage Wheel Drive Owner’s ManualSnow Thrower 247.888520Content TABLE OF CONTENTSWARRANTY INFORMATION PRODUCT SPECIFICATIONSPREPARATION SAFE OPERATION PRACTICESSAFETY TRAININGYOUR RESPONSIBILITY MAINTENANCE AND STORAGEHARDWARE PACK Loose Parts ASSEMBLYAttaching Handle Assembly Removing From CartonAttaching Chute ASSEMBLYAttaching Chute Crank Hex Lock Nut Attaching Clutch CablesLower Chute Crank BracketAttaching Turn Triggers Attaching Shift RodAuger Control Lamp WiringFinal Adjustments Trigger CableSkid Shoe Skid Shoe Remove these hardware to adjust skid shoeTire Pressure Pneumatic Tires Meets ANSI Safety Standards OPERATIONKnowing Your Snow Thrower Before Starting Engine Safety Ignition SwitchOperating Controls To Stop The Snow ThrowerPush To Start EngineStarting Instructions at a glance A. Electric StarterB. Recoil Starter Operating Snow ThrowerTo Throw Snow Warm StartRecoil Starter Operating TipsBefore Stopping To avoid possible freeze-up of the starter, followCustomer Responsibilities MAINTENANCEMAINTENANCE General RecommendationsLubrication Engine MaintenanceFigure 19 Lubrication Chart Viscosity ChartSpark Plug Changing OilTraction Drive Clutch SERVICE & ADJUSTMENTSAdjustments Chute AssemblyAugers ServiceADJUSTMENTS CarburetorDrive Belt PUSHNOTE Use care to avoid pinching the control cable NOTE Make sure that the auger cable is routed in front of the beltCover Changing Friction Wheel RubberNote If you placed plastic under the gas cap, be certain to remove it CarburetorSTORAGE OFF-SEASON STORAGEPreparing Engine Preparing Snow ThrowerCorrective Action TROUBLE-SHOOTINGTrouble Possible CausesBelt Shave Plate ACCESSORIESSpark Plug SEARS CRAFTSMAN 9.0 H.P. SNOW THROWER MODEL REPAIR PARTSPARTS LIST Drive Clutch Cable routed below axle and hooked here SEARS CRAFTSMAN 9.0 H.P. SNOW THROWER MODEL NOTE For painted parts, please refer to the list of Handle Support Bracket R.H. 5/8 Includes references 58 throughHex B-Tapp Screw # 10-16 x Handle Support Bracket L.H. 5/8SEARS CRAFTSMAN 9.0 H.P. SNOW THROWER MODEL SEARS CRAFTSMAN 9.0 H.P. SNOW THROWER MODEL Page Snow Thrower Model Craftsman Engine Model No. 143.999005 for CraftsmanTable continued on next page Recoil Starter CARBURETOR Page Page Page 5811-676-800 1 semana la a días 7 día, al horas 24 Llame domicilio, a entrega con piezas ordenar Paradomicilio, a reparación de servicio pedir Para 7084-659-800 1 semana la a días 7 pm, 7 a am 7 de Llameposible Causas DE LOCALIZACION DE TABLAProblema correctora Accionusa si carburador el drene No .carburador al llegue TEMPORAIENALMNADECNieve de Expulsor del Preparación motor del Preparación33 Figura colocadohaberlo de gasolina, de tapa la de debajo colocado 34 Figura32 Figura apropiadofuncionamiento un para fricción de rueda la en goma la simétricamente ensamblar importante Es NOTAde cable el apretar evitar para precavido Sea NOTA propulsora Correacorrea la de frente al encaminado esté control24 Figura Service25 Figura 23 Figura21 Figura AJUSTES & SERVICEAjustes Canaleta La De Conjuntosolvente un con lavando y alambre de cepillo Motor del Mantenimiento20 Figura comercialLubricacion MANTENIMIENCambios De Mecanismo cliente del Responsabilidadesoperación su con familiarizarse Ruedas La De PresionOperacion De Consejos Arranque de Abreviadas Instrucciones18 Figura sin cambios de palanca la mueva NUNCA NOTAPropulsor El Enganchar Para Motor El Apagar ComoNieve De Expulsor Del Detencion Motor Del ArranqueAceite Y Gasolina De Llenado eléctrico ArrancadorGatillo Del Palanca OPERACIONCambios De Palanca Nieve De Expulsor Su Conozcadesconectada está bujía la que asegurarse 16 FiguraDeslizante Zapata la de Ajuste Ajustes de sección la a refiérase detalles, más Para NOTA15 Figura transmisión la de cambiosFinales Ajustes Lámpara la de CableadoEmbrague Del Cables Los De Fijacion Cambios De Vara La De Fijaciony velocidad sexta de posición la de fuera cambios Giro De Gatillos Los De Fijacion6 Figura 9 Figura8 Figura 7 Figura4 Figura Canaleta La De FijacionCanaleta La De Manivela La De Fijacion 3 FiguraSueltas Piezas ENSAMBLADOMango Del Conjunto Del Fijacion Requeridas HerramientasFERRETERIA DE FERRETERIA DE CONJUNTO raspadora Barra gasolina de Recipiénte Correa NIEVE DE EXPULSOR DEL ACCESORIOSBujía tiempos dos de AceiteSears nieve de expulsor su de segura operación ENTRENAMIENTO OPERACION DE SEGURAS PRACTICASOPERACION PREPARACIONCONTENIDO DE TABLA INFORMACIÓN DE GARANTIAProducto Del Especificaciones 888520.247 Modelo De .No Propietario Del ManualFUERZA DE CABALLOS NIEVE DE EXPULSOR USA 60179 IL Estates, Hoffman ,.Co And Roebuck Sears
Top Page Image Contents