Sears 247.88852 owner manual Assembly, Removing From Carton, Loose Parts, Tools Required

Page 6

ASSEMBLY

ASSEMBLY

Handle Panel

Two-Piece

Chute Crank

Discharge Chute

Handles

Shift

Rod

Figure 1

Rear

Left

Right Front

IMPORTANT: This unit is shipped with engine oil in the engine, but without gasoline. After assembly, see OPERATION section of this manual for fuel selection and fill-up.

NOTE: To determine right and left hand sides of your snow thrower, stand behind the unit with the engine farthest away from you. See inset.

Your snow thrower has been completely assembled at the factory, except the handle and the handle panel, the discharge chute assembly, the chute crank assembly and the shift rod. These parts are shipped loose in the carton.

Removing From Carton

•Cut the corners of the carton and lay the sides flat on the ground. Remove all packing inserts.

•Remove all loose parts. For a complete list of the loose parts, refer to the following section.

•Move the snow thrower out of the carton.

•Make certain all parts and literature have been removed before discarding the carton.

Loose Parts

(See Figure 1.)

a.Handle Panel and Chute Assembly

b.Right Hand Handle

c.Left Hand Handle

d.Two-piece Chute Crank Assembly

e.Shift Rod

f.Hardware Pack

Assembly Tips: For easier assembly purposes, remove the chute from the carton and lay it on top of the engine. Do not unwrap the chute till you have installed the handle panel and the clutch cables.

Tools Required

1.1/2" , 7/16”, 3/8” wrenches or a set of adjustable wrenches

2.Set of pliers

3.Set of philips head screw drivers

4.Funnel to fill up gasoline

WARNING: Make certain the spark plug wire is disconnected and moved away from the spark plug before assembling the snow thrower.

Attaching Handle Assembly

•Stretch out control cables and place on the floor. Place the right handle in position with the flat side against the snow thrower. You can identify the right handle by the traction drive control label on it and the left handle by the auger clutch control label on it.

6

Image 6

Contents 247.888520 Owner’s ManualSnow Thrower 9 Horse Power 26” Two-Stage Wheel DrivePRODUCT SPECIFICATIONS TABLE OF CONTENTSWARRANTY INFORMATION ContentTRAINING SAFE OPERATION PRACTICESSAFETY PREPARATIONMAINTENANCE AND STORAGE YOUR RESPONSIBILITYHARDWARE PACK Removing From Carton ASSEMBLYAttaching Handle Assembly Loose PartsASSEMBLY Attaching ChuteAttaching Chute Crank Crank Bracket Attaching Clutch CablesLower Chute Hex Lock NutAttaching Shift Rod Attaching Turn TriggersTrigger Cable Lamp WiringFinal Adjustments Auger ControlSkid Shoe Remove these hardware to adjust skid shoe Skid ShoeTire Pressure Pneumatic Tires OPERATION Meets ANSI Safety StandardsKnowing Your Snow Thrower To Stop The Snow Thrower Safety Ignition SwitchOperating Controls Before Starting EngineA. Electric Starter To Start EngineStarting Instructions at a glance PushWarm Start Operating Snow ThrowerTo Throw Snow B. Recoil StarterTo avoid possible freeze-up of the starter, follow Operating TipsBefore Stopping Recoil StarterGeneral Recommendations MAINTENANCEMAINTENANCE Customer ResponsibilitiesViscosity Chart Engine MaintenanceFigure 19 Lubrication Chart LubricationChanging Oil Spark PlugChute Assembly SERVICE & ADJUSTMENTSAdjustments Traction Drive ClutchCarburetor ServiceADJUSTMENTS AugersNOTE Make sure that the auger cable is routed in front of the belt PUSHNOTE Use care to avoid pinching the control cable Drive BeltChanging Friction Wheel Rubber CoverCarburetor Note If you placed plastic under the gas cap, be certain to remove itPreparing Snow Thrower OFF-SEASON STORAGEPreparing Engine STORAGEPossible Causes TROUBLE-SHOOTINGTrouble Corrective ActionACCESSORIES Belt Shave PlateSpark Plug REPAIR PARTS SEARS CRAFTSMAN 9.0 H.P. SNOW THROWER MODELPARTS LIST Drive Clutch Cable routed below axle and hooked here SEARS CRAFTSMAN 9.0 H.P. SNOW THROWER MODEL NOTE For painted parts, please refer to the list of Handle Support Bracket L.H. 5/8 Includes references 58 throughHex B-Tapp Screw # 10-16 x Handle Support Bracket R.H. 5/8SEARS CRAFTSMAN 9.0 H.P. SNOW THROWER MODEL SEARS CRAFTSMAN 9.0 H.P. SNOW THROWER MODEL Page Craftsman Engine Model No. 143.999005 for Craftsman Snow Thrower ModelTable continued on next page Recoil Starter CARBURETOR Page Page Page 7084-659-800 1 semana la a días 7 pm, 7 a am 7 de Llame domicilio, a entrega con piezas ordenar Paradomicilio, a reparación de servicio pedir Para 5811-676-800 1 semana la a días 7 día, al horas 24 Llamecorrectora Accion DE LOCALIZACION DE TABLAProblema posible Causasmotor del Preparación TEMPORAIENALMNADECNieve de Expulsor del Preparación usa si carburador el drene No .carburador al llegue34 Figura colocadohaberlo de gasolina, de tapa la de debajo colocado 33 Figurala simétricamente ensamblar importante Es NOTA apropiadofuncionamiento un para fricción de rueda la en goma 32 Figuracontrol propulsora Correacorrea la de frente al encaminado esté de cable el apretar evitar para precavido Sea NOTA23 Figura Service25 Figura 24 FiguraCanaleta La De Conjunto AJUSTES & SERVICEAjustes 21 Figuracomercial Motor del Mantenimiento20 Figura solvente un con lavando y alambre de cepillocliente del Responsabilidades MANTENIMIENCambios De Mecanismo LubricacionArranque de Abreviadas Instrucciones Ruedas La De PresionOperacion De Consejos operación su con familiarizarseMotor El Apagar Como sin cambios de palanca la mueva NUNCA NOTAPropulsor El Enganchar Para 18 Figuraeléctrico Arrancador Motor Del ArranqueAceite Y Gasolina De Llenado Nieve De Expulsor Del DetencionNieve De Expulsor Su Conozca OPERACIONCambios De Palanca Gatillo Del PalancaAjustes de sección la a refiérase detalles, más Para NOTA 16 FiguraDeslizante Zapata la de Ajuste desconectada está bujía la que asegurarseLámpara la de Cableado transmisión la de cambiosFinales Ajustes 15 FiguraGiro De Gatillos Los De Fijacion Cambios De Vara La De Fijaciony velocidad sexta de posición la de fuera cambios Embrague Del Cables Los De Fijacion7 Figura 9 Figura8 Figura 6 Figura3 Figura Canaleta La De FijacionCanaleta La De Manivela La De Fijacion 4 FiguraRequeridas Herramientas ENSAMBLADOMango Del Conjunto Del Fijacion Sueltas PiezasFERRETERIA DE FERRETERIA DE CONJUNTO tiempos dos de Aceite NIEVE DE EXPULSOR DEL ACCESORIOSBujía raspadora Barra gasolina de Recipiénte CorreaSears nieve de expulsor su de segura operación PREPARACION OPERACION DE SEGURAS PRACTICASOPERACION ENTRENAMIENTOINFORMACIÓN DE GARANTIA CONTENIDO DE TABLAProducto Del Especificaciones USA 60179 IL Estates, Hoffman ,.Co And Roebuck Sears Propietario Del ManualFUERZA DE CABALLOS NIEVE DE EXPULSOR 888520.247 Modelo De .No