Sears 247.88852 Carburetor, Note If you placed plastic under the gas cap, be certain to remove it

Page 24

Note: If you placed plastic under the gas cap, be certain to remove it.

in position. See Figure 32.

Shift Arm Assembly

Sprocket

Spacer

Pin

Friction Wheel

Figure 32

•Slide the hex shaft through the left side of the housing and through the friction wheel assembly.

•Insert the hex shaft through the sprocket and the spacer. See Figure 33. Make certain that the chain engages both the large and the small sprocket.

NOTE: If the sprocket fell from the snow thrower while removing the hex shaft, place the sprocket on the hex shaft. Position the hex hub of the sprocket

toward the friction wheel when sliding the sprocket on to the hex shaft. See Figure 33.

Sprocket

Spacer

Hex

Shaft

Hex Hub

of Sprocket

Figure 33

•Align the hex shaft with the right hand bearing and carefully guide the left hand bearing into the left side of the housing.

•Reassemble the drive cover with the four screws that were earlier removed.

Note: If you placed plastic under the gas cap, be certain to remove it.

Carburetor

WARNING: If any adjustments are made to the engine while the engine is running (e.g. carburetor), keep clear of all moving parts. Be careful of heated surfaces and muffler.

If you think the carburetor needs to be adjusted, see your nearest authorized Sears Service Outlet.

24

Image 24

Contents Owner’s Manual Snow Thrower247.888520 9 Horse Power 26” Two-Stage Wheel DriveTABLE OF CONTENTS WARRANTY INFORMATIONPRODUCT SPECIFICATIONS ContentSAFE OPERATION PRACTICES SAFETYTRAINING PREPARATIONMAINTENANCE AND STORAGE YOUR RESPONSIBILITYHARDWARE PACK ASSEMBLY Attaching Handle AssemblyRemoving From Carton Loose PartsASSEMBLY Attaching ChuteAttaching Chute Crank Attaching Clutch Cables Lower ChuteCrank Bracket Hex Lock NutAttaching Shift Rod Attaching Turn TriggersLamp Wiring Final AdjustmentsTrigger Cable Auger ControlSkid Shoe Remove these hardware to adjust skid shoe Skid ShoeTire Pressure Pneumatic Tires OPERATION Meets ANSI Safety StandardsKnowing Your Snow Thrower Safety Ignition Switch Operating ControlsTo Stop The Snow Thrower Before Starting EngineTo Start Engine Starting Instructions at a glanceA. Electric Starter PushOperating Snow Thrower To Throw SnowWarm Start B. Recoil StarterOperating Tips Before StoppingTo avoid possible freeze-up of the starter, follow Recoil StarterMAINTENANCE MAINTENANCEGeneral Recommendations Customer ResponsibilitiesEngine Maintenance Figure 19 Lubrication ChartViscosity Chart LubricationChanging Oil Spark PlugSERVICE & ADJUSTMENTS AdjustmentsChute Assembly Traction Drive ClutchService ADJUSTMENTSCarburetor AugersPUSH NOTE Use care to avoid pinching the control cableNOTE Make sure that the auger cable is routed in front of the belt Drive BeltChanging Friction Wheel Rubber CoverCarburetor Note If you placed plastic under the gas cap, be certain to remove itOFF-SEASON STORAGE Preparing EnginePreparing Snow Thrower STORAGETROUBLE-SHOOTING TroublePossible Causes Corrective ActionACCESSORIES Belt Shave PlateSpark Plug REPAIR PARTS SEARS CRAFTSMAN 9.0 H.P. SNOW THROWER MODELPARTS LIST Drive Clutch Cable routed below axle and hooked here SEARS CRAFTSMAN 9.0 H.P. SNOW THROWER MODEL NOTE For painted parts, please refer to the list of Includes references 58 through Hex B-Tapp Screw # 10-16 xHandle Support Bracket L.H. 5/8 Handle Support Bracket R.H. 5/8SEARS CRAFTSMAN 9.0 H.P. SNOW THROWER MODEL SEARS CRAFTSMAN 9.0 H.P. SNOW THROWER MODEL Page Craftsman Engine Model No. 143.999005 for Craftsman Snow Thrower ModelTable continued on next page Recoil Starter CARBURETOR Page Page Page domicilio, a entrega con piezas ordenar Para domicilio, a reparación de servicio pedir Para7084-659-800 1 semana la a días 7 pm, 7 a am 7 de Llame 5811-676-800 1 semana la a días 7 día, al horas 24 LlameDE LOCALIZACION DE TABLA Problemacorrectora Accion posible CausasTEMPORAIENALMNADEC Nieve de Expulsor del Preparaciónmotor del Preparación usa si carburador el drene No .carburador al lleguecolocado haberlo de gasolina, de tapa la de debajo colocado34 Figura 33 Figuraapropiado funcionamiento un para fricción de rueda la en gomala simétricamente ensamblar importante Es NOTA 32 Figurapropulsora Correa correa la de frente al encaminado estécontrol de cable el apretar evitar para precavido Sea NOTAService 25 Figura23 Figura 24 FiguraAJUSTES & SERVICE AjustesCanaleta La De Conjunto 21 FiguraMotor del Mantenimiento 20 Figuracomercial solvente un con lavando y alambre de cepilloMANTENIMIEN Cambios De Mecanismocliente del Responsabilidades LubricacionRuedas La De Presion Operacion De ConsejosArranque de Abreviadas Instrucciones operación su con familiarizarsesin cambios de palanca la mueva NUNCA NOTA Propulsor El Enganchar ParaMotor El Apagar Como 18 FiguraMotor Del Arranque Aceite Y Gasolina De Llenadoeléctrico Arrancador Nieve De Expulsor Del DetencionOPERACION Cambios De PalancaNieve De Expulsor Su Conozca Gatillo Del Palanca16 Figura Deslizante Zapata la de AjusteAjustes de sección la a refiérase detalles, más Para NOTA desconectada está bujía la que asegurarsetransmisión la de cambios Finales AjustesLámpara la de Cableado 15 FiguraCambios De Vara La De Fijacion y velocidad sexta de posición la de fuera cambiosGiro De Gatillos Los De Fijacion Embrague Del Cables Los De Fijacion9 Figura 8 Figura7 Figura 6 FiguraCanaleta La De Fijacion Canaleta La De Manivela La De Fijacion3 Figura 4 FiguraENSAMBLADO Mango Del Conjunto Del FijacionRequeridas Herramientas Sueltas PiezasFERRETERIA DE FERRETERIA DE CONJUNTO NIEVE DE EXPULSOR DEL ACCESORIOS Bujíatiempos dos de Aceite raspadora Barra gasolina de Recipiénte CorreaSears nieve de expulsor su de segura operación OPERACION DE SEGURAS PRACTICAS OPERACIONPREPARACION ENTRENAMIENTOINFORMACIÓN DE GARANTIA CONTENIDO DE TABLAProducto Del Especificaciones Propietario Del Manual FUERZA DE CABALLOS NIEVE DE EXPULSORUSA 60179 IL Estates, Hoffman ,.Co And Roebuck Sears 888520.247 Modelo De .No