Sears 247.88852 owner manual Skid Shoe Remove these hardware to adjust skid shoe

Page 11

Skid Shoe

should be no resistance in the shift lever, and the wheels should turn.

•If you face resistance when moving the shift lever or the snow thrower wheels stop when they should not, loosen the lock nut on the traction drive cable and unthread the cable one turn.

•If the wheels can still be turned when you engage the traction drive clutch grip, loosen the lock nut on the traction drive cable and thread the cable in one turn.

•Recheck the adjustment and repeat adjustment as necessary. Tighten the lock nut to secure the cable when correct adjustment is reached.

NOTE: If you are not sure that you have reached correct adjustment, refer to the Adjustment section on page 20.

Skid Shoe

The space between the shave plate and the ground can be adjusted. For close snow removal, place skid shoes in the low position. Use middle or high position when area to be cleared is uneven.

NOTE: It is not recommended that you operate this snow thrower on gravel as loose gravel can be easily picked up and thrown by the auger causing an injury or damage to the snow thrower.

•If for some reason, you have to operate the snow thrower on gravel, keep the skid shoe in the highest position for maximum clearance between the ground and the shave plate.

•Adjust skid shoes by loosening the four hex nuts and carriage bolts and moving skid shoes to desired position.

•Make certain the entire bottom surface of skid shoe is against the ground to avoid uneven wear on the skid shoes.

•Tighten nuts and bolts securely.

Skid Shoe Remove these hardware

to adjust skid shoe

Figure 16

•If for some reason, you have to operate the snow thrower on gravel, keep the skid shoe in the highest position for maximum clearance between the ground and the shave plate.

Tire Pressure (Pneumatic Tires)

The tires are over-inflated for shipping purposes. Check tire pressure and reduce to 15 to 20 psi.

NOTE: If the tire pressure is not equal in both tires, the unit may pull to one side or the other.

11

Image 11

Contents 9 Horse Power 26” Two-Stage Wheel Drive Owner’s ManualSnow Thrower 247.888520Content TABLE OF CONTENTSWARRANTY INFORMATION PRODUCT SPECIFICATIONSPREPARATION SAFE OPERATION PRACTICESSAFETY TRAININGYOUR RESPONSIBILITY MAINTENANCE AND STORAGEHARDWARE PACK Loose Parts ASSEMBLYAttaching Handle Assembly Removing From CartonAttaching Chute Crank ASSEMBLYAttaching Chute Hex Lock Nut Attaching Clutch CablesLower Chute Crank BracketAttaching Turn Triggers Attaching Shift RodAuger Control Lamp WiringFinal Adjustments Trigger CableTire Pressure Pneumatic Tires Skid Shoe Remove these hardware to adjust skid shoeSkid Shoe Knowing Your Snow Thrower OPERATIONMeets ANSI Safety Standards Before Starting Engine Safety Ignition SwitchOperating Controls To Stop The Snow ThrowerPush To Start EngineStarting Instructions at a glance A. Electric StarterB. Recoil Starter Operating Snow ThrowerTo Throw Snow Warm StartRecoil Starter Operating TipsBefore Stopping To avoid possible freeze-up of the starter, followCustomer Responsibilities MAINTENANCEMAINTENANCE General RecommendationsLubrication Engine MaintenanceFigure 19 Lubrication Chart Viscosity ChartSpark Plug Changing OilTraction Drive Clutch SERVICE & ADJUSTMENTSAdjustments Chute AssemblyAugers ServiceADJUSTMENTS CarburetorDrive Belt PUSHNOTE Use care to avoid pinching the control cable NOTE Make sure that the auger cable is routed in front of the beltCover Changing Friction Wheel RubberNote If you placed plastic under the gas cap, be certain to remove it CarburetorSTORAGE OFF-SEASON STORAGEPreparing Engine Preparing Snow ThrowerCorrective Action TROUBLE-SHOOTINGTrouble Possible CausesSpark Plug ACCESSORIESBelt Shave Plate SEARS CRAFTSMAN 9.0 H.P. SNOW THROWER MODEL REPAIR PARTSPARTS LIST Drive Clutch Cable routed below axle and hooked here SEARS CRAFTSMAN 9.0 H.P. SNOW THROWER MODEL NOTE For painted parts, please refer to the list of Handle Support Bracket R.H. 5/8 Includes references 58 throughHex B-Tapp Screw # 10-16 x Handle Support Bracket L.H. 5/8SEARS CRAFTSMAN 9.0 H.P. SNOW THROWER MODEL SEARS CRAFTSMAN 9.0 H.P. SNOW THROWER MODEL Page Table continued on next page Craftsman Engine Model No. 143.999005 for CraftsmanSnow Thrower Model Recoil Starter CARBURETOR Page Page Page 5811-676-800 1 semana la a días 7 día, al horas 24 Llame domicilio, a entrega con piezas ordenar Paradomicilio, a reparación de servicio pedir Para 7084-659-800 1 semana la a días 7 pm, 7 a am 7 de Llameposible Causas DE LOCALIZACION DE TABLAProblema correctora Accionusa si carburador el drene No .carburador al llegue TEMPORAIENALMNADECNieve de Expulsor del Preparación motor del Preparación33 Figura colocadohaberlo de gasolina, de tapa la de debajo colocado 34 Figura32 Figura apropiadofuncionamiento un para fricción de rueda la en goma la simétricamente ensamblar importante Es NOTAde cable el apretar evitar para precavido Sea NOTA propulsora Correacorrea la de frente al encaminado esté control24 Figura Service25 Figura 23 Figura21 Figura AJUSTES & SERVICEAjustes Canaleta La De Conjuntosolvente un con lavando y alambre de cepillo Motor del Mantenimiento20 Figura comercialLubricacion MANTENIMIENCambios De Mecanismo cliente del Responsabilidadesoperación su con familiarizarse Ruedas La De PresionOperacion De Consejos Arranque de Abreviadas Instrucciones18 Figura sin cambios de palanca la mueva NUNCA NOTAPropulsor El Enganchar Para Motor El Apagar ComoNieve De Expulsor Del Detencion Motor Del ArranqueAceite Y Gasolina De Llenado eléctrico ArrancadorGatillo Del Palanca OPERACIONCambios De Palanca Nieve De Expulsor Su Conozcadesconectada está bujía la que asegurarse 16 FiguraDeslizante Zapata la de Ajuste Ajustes de sección la a refiérase detalles, más Para NOTA15 Figura transmisión la de cambiosFinales Ajustes Lámpara la de CableadoEmbrague Del Cables Los De Fijacion Cambios De Vara La De Fijaciony velocidad sexta de posición la de fuera cambios Giro De Gatillos Los De Fijacion6 Figura 9 Figura8 Figura 7 Figura4 Figura Canaleta La De FijacionCanaleta La De Manivela La De Fijacion 3 FiguraSueltas Piezas ENSAMBLADOMango Del Conjunto Del Fijacion Requeridas HerramientasFERRETERIA DE FERRETERIA DE CONJUNTO raspadora Barra gasolina de Recipiénte Correa NIEVE DE EXPULSOR DEL ACCESORIOSBujía tiempos dos de AceiteSears nieve de expulsor su de segura operación ENTRENAMIENTO OPERACION DE SEGURAS PRACTICASOPERACION PREPARACIONProducto Del Especificaciones INFORMACIÓN DE GARANTIACONTENIDO DE TABLA 888520.247 Modelo De .No Propietario Del ManualFUERZA DE CABALLOS NIEVE DE EXPULSOR USA 60179 IL Estates, Hoffman ,.Co And Roebuck Sears