Cub Cadet 930 SWE, 933 SWE warranty Operating Your Snow Thrower, Know Your Snow Thrower

Page 10

4

Operating

Your Snow

Thrower

WARNING

Read, understand, and follow all instruc- tions and warnings on the machine and in this manual before operating.

Know Your Snow Thrower

 

 

Drive Control

 

 

Shift Lever

 

 

Two-Way

 

 

Chute Control™

 

 

Auger Control

Gas Cap

Headlight

Wheel Steering

 

Control

Fuel Tank

 

 

 

Oil Fill

 

 

Chute

 

Chute

 

Directional

Assembly

 

Control

 

 

 

 

Engine Controls

 

 

Recoil Starter

 

 

Handle

 

 

Electric Starter Outlet

 

 

Primer

 

 

Ignition

 

 

Key

 

 

Choke

 

 

Control

 

Clean-Out

Throttle

 

Tool

Control

33-inch model shown

Skid Shoe

 

Figure 4-1

Now that you have setup your snow thrower, it’s important to become acquainted with its controls and features.

For detailed starting instructions and more information on all engine controls, refer to the Tecumseh Engine manual packed separately.

Specifications are subject to change without notification or obligation. Images may not reflect your exact model and are for reference purposes only.

NOTE: For detailed starting instructions and more information on all engine controls, refer to the Tecumseh Engines manual packed separately and Starting The Engine later in this section.

Shift Lever

The shift lever is located in the center of the handle panel. Place the shift lever into any of eight positions to control the direction of travel and ground speed.

Forward

Your snow thrower has six forward (F) speeds, with position number one (1) being the slowest speed.

Reverse

Your snow thrower has two reverse (R) speeds, with position number one (1) being the slower speed.

Choke Control

The choke control

is found on the rear of the engine and is

activated by rotating the knob clockwise. Activating the choke control closes the choke plate on the carburetor and aids in starting the engine.

Throttle Control

The throttle control is located on the engine. It regulates the speed of the engine and will shut off the engine when pushed down completely.

Primer

Depressing the primer forces fuel directly into the engine’s carburetor to aid in cold-weather starting.

Oil Fill

Engine oil level can be checked and oil added

through the oil fill.

34/0

10

Image 10
Contents 31AE9PSV710 31AE9LSU710 31AE9LSU756 Two Stage Snow Thrower Models 930 SWE & 933 SWE28/06 Finding and Recording Model Number Table of ContentsCustomer Support %, 352&!#%3 Your Responsibility53% %842! #!54/ %. /0%2!4  2%!$ /0%2!4/2g3 -!.5!,TrainingPreparation Your Responsibility Restrict the useDo not modify engine Maintenance & StorageOperation Your ResponsibilitySetting Up Your Snow Thrower Shear Pin Storage Testing Drive Control & Shift Lever Final AdjustmentsTesting Auger Drive Control Tire Pressure Pneumatic Tires Adjusting Drive and Auger ControlsAdjust the lock nut as follows Reattach the spring to the actuator bracketOperating Your Snow Thrower Know Your Snow Thrower$26% #/.42 Electric Starter Gas & Oil Fill-UpStarting The Engine Recoil StarterTo Engage Drive Chute Clean-Out ToolStopping The Engine To Engage AugersChute Control Making AdjustmentsShift Cable Drive ControlSkid Shoes Wheel Making AdjustmentsChute Bracket Adjustment Auger ControlLubrication Maintaining Your Snow ThrowerEngine AugersReplacing Belts Shave Plate Skid ShoesShave Plate Auger BeltDisconnect spark Performing any type Maintenance on Your machineAlways stop engine Plug, and ground Against engine beforeDrive Belt Changing Friction Wheel Hex ShaftHub Assembly Friction Wheel Secure with the cupped washer and hex bolt removed earlierPreparing Snow Thrower Off-Season StoragePreparing Engine Short-Term StorageThis section addresses minor service issues Problem Cause RemedyFor further details Contact an authorized Service center Trouble- shootingModels 930 SWE & 933 SWE Or visit Parts ListTo order replacement Parts, call the Customer Dealer Referral Line atModels 930 SWE & 933 SWE Steering Control 79 8 9878 79 710-0237 Screw, 5/16-24 x From previous U.S.A Canada Contact MTD Products Limited, Kitchener, on N2G 4J1, or callMANUFACTURER’S Limited Warranty for