Cub Cadet 933 SWE, 930 SWE Adjusting Drive and Auger Controls, Tire Pressure Pneumatic Tires

Page 9

Adjusting Drive and Auger Controls

1.From beneath the handle, pull downward on the appropriate cable and unhook the spring found on the end of the cable from its respective actuator bracket. Refer to Figures 3-8 and 3-9.

2.Slide the spring up the cable to expose the cable coupler threads and lock nut. Refer to Figure 3-10.

Adjust the lock nut as follows:

3.If adjusting the drive cable, thread the lock nut outward (down the coupler) to lengthen the cable and allow the unit to move freely when the control is released. Thread the lock nut inward (up the coupler) to shorten the cable to reduce slippage and prevent the machine from being easily moved with the drive control engaged.

4.If adjusting the auger cable, thread the lock nut down to lengthen the cable as necessary to stop the auger from turning when the control is released.

WARNING: Do not over-tighten the cable. Over-tightening may prevent the auger from disengaging and compro- mise the safety of the snow thrower.

5.Reattach the spring to the actuator bracket.

6.Repeat the wheel drive and auger control tests to verify proper adjustment. Repeat previous steps if necessary to attain proper adjustment of each cable.

Tire Pressure (Pneumatic Tires)

The tires are over-inflated for shipping purposes. Check the tire pressure before operating the snow thrower. Refer to the tire side wall for tire manufacturer’s recommended psi and deflate (or inflate) the tires as necessary.

NOTE: If the tire pressure is not equal in both tires, the unit may pull to one side or the other and the shave plate will not sit level on the ground.

IMPORTANT: Under any circumstance do not exceed manufacturer’s recommended psi. Equal tire pressure should be maintained at all times. Excessive pressure when seating beads may cause tire/rim assembly to burst with force sufficient to cause serious injury. Refer to sidewall of tire for recommended pressure.

Figure 3-9

Figure 3-10

3

Setting Up

Your Snow

Thrower

WARNING

Do not over-tighten the cable. Over-tightening may prevent the auger from disengaging and compro- mise the safety of the snow thrower.

IMPORTANT: Under any circumstance do not exceed manufacturer’s recommended psi. Equal tire pressure should be maintained at all times. Excessive pressure when seating beads may cause tire/rim assembly to burst with force sufficient to cause serious injury. Refer to sidewall of tire for recommended pressure.

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Two Stage Snow Thrower Models 930 SWE & 933 SWE 31AE9PSV710 31AE9LSU710 31AE9LSU75628/06 Table of Contents Finding and Recording Model NumberCustomer Support 53% %842! #!54/ %. /0%2!4 Your Responsibility%, 352&!#%3  2%!$ /0%2!4/2g3 -!.5!,Your Responsibility Restrict the use TrainingPreparationOperation Maintenance & StorageDo not modify engine Your ResponsibilitySetting Up Your Snow Thrower Shear Pin Storage Final Adjustments Testing Drive Control & Shift LeverTesting Auger Drive Control Adjust the lock nut as follows Adjusting Drive and Auger ControlsTire Pressure Pneumatic Tires Reattach the spring to the actuator bracketKnow Your Snow Thrower Operating Your Snow Thrower$26% #/.42 Starting The Engine Gas & Oil Fill-UpElectric Starter Recoil StarterStopping The Engine Chute Clean-Out ToolTo Engage Drive To Engage AugersShift Cable Making AdjustmentsChute Control Drive ControlChute Bracket Adjustment Wheel Making AdjustmentsSkid Shoes Auger ControlEngine Maintaining Your Snow ThrowerLubrication AugersShave Plate Shave Plate Skid ShoesReplacing Belts Auger BeltAlways stop engine Performing any type Maintenance on Your machineDisconnect spark Plug, and ground Against engine beforeDrive Belt Hex Shaft Changing Friction WheelSecure with the cupped washer and hex bolt removed earlier Hub Assembly Friction WheelPreparing Engine Off-Season StoragePreparing Snow Thrower Short-Term StorageFor further details Contact an authorized Service center Problem Cause RemedyThis section addresses minor service issues Trouble- shootingModels 930 SWE & 933 SWE To order replacement Parts ListOr visit Parts, call the Customer Dealer Referral Line atModels 930 SWE & 933 SWE Steering Control 79 8 9878 79 710-0237 Screw, 5/16-24 x From previous Contact MTD Products Limited, Kitchener, on N2G 4J1, or call U.S.A CanadaMANUFACTURER’S Limited Warranty for
Top Page Image Contents