Cub Cadet 930 SWE, 933 SWE warranty TrainingPreparation, Your Responsibility Restrict the use

Page 4

2

Safe

Operation

WARNING: Engine Exhaust, some of its constituents, and certain vehicle compo- nents contain or emit chemicals known to State of California to cause cancer and birth defects or other reproductive harm.

DANGER: This machine was built to be operated according to the rules for safe operation in this manual. As with any type of power equipment, carelessness or error on the part of the operator can result in serious injury. This machine is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury or death.

TrainingPreparation

Practices

WARNING

This symbol points out important safety instructions which, if not followed, could endanger the personal safety and/or property of yourself and others. Read and follow all instructions in this manual before at- tempting to operate this machine. Failure to comply with these instructions may result in personal injury. When you see this symbol.

HEED ITS WARNING!

Your Responsibility Restrict the use

of this power machine to persons who read, understand

and follow the warnings and instructions

in this manual

and on the machine.

1.Read, understand, and follow all instructions on the machine and in the manual(s) before attempting to assemble and operate. Keep this manual in a safe place for future and regular reference and for ordering replacement parts.

2.Be familiar with all controls and their proper operation. Know how to stop the machine and disengage them quickly.

3.Never allow children under 14 years old to operate this machine. Children 14 years old and over should read and understand the operation instructions and safety rules in this manual and should be trained and supervised by a parent.

4.Never allow adults to operate this machine without proper instruction.

5.Thrown objects can cause serious personal injury. Plan your snow-throwing pattern to avoid discharge of material toward roads, bystanders and the like.

6.Keep bystanders, helpers, pets and children at least 75 feet from the machine while it is in operation. Stop machine if anyone enters the area.

7.Exercise caution to avoid slipping or falling, especially when operating in reverse.

1.Thoroughly inspect the area where the equipment is to be used. Remove all doormats, newspapers, sleds, boards, wires and other foreign objects, which could be tripped over or thrown by the auger/impeller.

2.Always wear safety glasses or eye shields during operation and while performing an adjustment or repair to protect your eyes. Thrown objects which ricochet can cause serious injury to the eyes.

3.Do not operate without wearing adequate winter outer garments. Do not wear jewelry, long scarves or other loose clothing, which could become entangled in moving parts. Wear footwear which will improve footing on slippery surfaces.

4.Use a grounded three-wire extension cord and receptacle for all units with electric start engines.

5.Adjust collector housing height to clear gravel or crushed rock surfaces.

6.Disengage all control levers before starting the engine.

7.Never attempt to make any adjustments while engine is running, except where specifically recommended in the operator’s manual.

8.Let engine and machine adjust to outdoor temperature before starting to clear snow.

9.To avoid personal injury or property damage use extreme care in handling gasoline. Gasoline is extremely flammable and the vapors are explosive. Serious personal injury can occur when gasoline is spilled on yourself or your clothes, which can ignite. Wash your skin and change clothes immediately.

a.Use only an approved gasoline container.

b.Extinguish all cigarettes, cigars, pipes and other sources of ignition.

c.Never fuel machine indoors.

d.Never remove gas cap or add fuel while the engine is hot or running.

e.Allow engine to cool at least two minutes before refuel- ing.

f.Never over fill fuel tank. Fill tank to no more than ½ inch below bottom of filler neck to provide space for fuel expansion.

g.Replace gasoline cap and tighten securely.

h.If gasoline is spilled, wipe it off the engine and equip- ment. Move machine to another area. Wait 5 minutes before starting the engine.

i.Never store the machine or fuel container inside where there is an open flame, spark or pilot light (e.g. furnace, water heater, space heater, clothes dryer etc.).

j.Allow machine to cool at least 5 minutes before storing.

Image 4
Contents 31AE9PSV710 31AE9LSU710 31AE9LSU756 Two Stage Snow Thrower Models 930 SWE & 933 SWE28/06 Finding and Recording Model Number Table of ContentsCustomer Support Your Responsibility 53% %842! #!54/ %. /0%2!4%, 352&!#%3  2%!$ /0%2!4/2g3 -!.5!,TrainingPreparation Your Responsibility Restrict the useMaintenance & Storage OperationDo not modify engine Your ResponsibilitySetting Up Your Snow Thrower Shear Pin Storage Testing Drive Control & Shift Lever Final AdjustmentsTesting Auger Drive Control Adjusting Drive and Auger Controls Adjust the lock nut as followsTire Pressure Pneumatic Tires Reattach the spring to the actuator bracketOperating Your Snow Thrower Know Your Snow Thrower$26% #/.42 Gas & Oil Fill-Up Starting The EngineElectric Starter Recoil StarterChute Clean-Out Tool Stopping The EngineTo Engage Drive To Engage AugersMaking Adjustments Shift CableChute Control Drive ControlWheel Making Adjustments Chute Bracket AdjustmentSkid Shoes Auger ControlMaintaining Your Snow Thrower EngineLubrication AugersShave Plate Skid Shoes Shave PlateReplacing Belts Auger BeltPerforming any type Maintenance on Your machine Always stop engineDisconnect spark Plug, and ground Against engine beforeDrive Belt Changing Friction Wheel Hex ShaftHub Assembly Friction Wheel Secure with the cupped washer and hex bolt removed earlierOff-Season Storage Preparing EnginePreparing Snow Thrower Short-Term StorageProblem Cause Remedy For further details Contact an authorized Service centerThis section addresses minor service issues Trouble- shootingModels 930 SWE & 933 SWE Parts List To order replacementOr visit Parts, call the Customer Dealer Referral Line atModels 930 SWE & 933 SWE Steering Control 79 8 9878 79 710-0237 Screw, 5/16-24 x From previous U.S.A Canada Contact MTD Products Limited, Kitchener, on N2G 4J1, or callMANUFACTURER’S Limited Warranty for