Cub Cadet 930 SWE, 933 SWE warranty Setting Up Your Snow Thrower

Page 6

3

Setting Up

Your Snow

Thrower

NOTE: All references in this manual to the left or right side of the snow thrower is from the operating position only. Exceptions, if any, will be specified.

IMPORTANT

This unit is shipped with the engine full of oil. After assembly, refer to the Tecumseh Engines manual packed separately with your snow thrower for fuel and oil fill-up details.

Specifications are subject to change without notification or obligation. Images may not reflect your exact model and are for reference purposes only.

Figure 3-1

Figure 3-2

IMPORTANT: Two replacement auger shear pins are included with this manual (or stowed in the plastic handle panel). Refer to the Maintenance section for more information regarding shear pin replacement.

NOTE: All references in this manual to the left or right side of the snow thrower is from the operating position only. Exceptions, if any, will be specified.

IMPORTANT: This unit is shipped with the engine full of oil. After assembly, refer to the Tecumseh Engine manual packed separately with your snow thrower for fuel and oil fill-up details.

NOTE: Specifications are subject to change without notification or obligation. Images may not reflect your exact model and are for reference purposes only.

1.Observe the lower area of the snow thrower to be sure both cables are aligned with roller guides before pivoting handle upward.

a.Remove the lower star knob and carriage bolt from each side of the lower handle. Pull up and back on upper handle as shown in Figure 3-1. Align upper handle with the lower handle. Make certain the springs at the lower end of the auger and drive cables are securely hooked into their respective

actuator bracket.

2. a. Secure the upper handle and lower handle with the two star knobs and carriage bolts removed earlier. See Figure 3-2.

b. Tighten the two star knobs already installed in the upper holes to firmly secure the upper handle and support tubes.

Figure 3-3

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Two Stage Snow Thrower Models 930 SWE & 933 SWE 31AE9PSV710 31AE9LSU710 31AE9LSU75628/06 Table of Contents Finding and Recording Model NumberCustomer Support %, 352&!#%3 Your Responsibility53% %842! #!54/ %. /0%2!4  2%!$ /0%2!4/2g3 -!.5!,TrainingPreparation Your Responsibility Restrict the useDo not modify engine Maintenance & StorageOperation Your ResponsibilitySetting Up Your Snow Thrower Shear Pin Storage Final Adjustments Testing Drive Control & Shift LeverTesting Auger Drive Control Tire Pressure Pneumatic Tires Adjusting Drive and Auger ControlsAdjust the lock nut as follows Reattach the spring to the actuator bracketOperating Your Snow Thrower Know Your Snow Thrower$26% #/.42 Electric Starter Gas & Oil Fill-UpStarting The Engine Recoil StarterTo Engage Drive Chute Clean-Out ToolStopping The Engine To Engage AugersChute Control Making AdjustmentsShift Cable Drive ControlSkid Shoes Wheel Making AdjustmentsChute Bracket Adjustment Auger ControlLubrication Maintaining Your Snow ThrowerEngine AugersReplacing Belts Shave Plate Skid ShoesShave Plate Auger BeltDisconnect spark Performing any type Maintenance on Your machineAlways stop engine Plug, and ground Against engine beforeDrive Belt Changing Friction Wheel Hex ShaftHub Assembly Friction Wheel Secure with the cupped washer and hex bolt removed earlierPreparing Snow Thrower Off-Season StoragePreparing Engine Short-Term StorageThis section addresses minor service issues Problem Cause RemedyFor further details Contact an authorized Service center Trouble- shootingModels 930 SWE & 933 SWE Or visit Parts ListTo order replacement Parts, call the Customer Dealer Referral Line atModels 930 SWE & 933 SWE Steering Control 79 8 9878 79 710-0237 Screw, 5/16-24 x From previous U.S.A Canada Contact MTD Products Limited, Kitchener, on N2G 4J1, or callMANUFACTURER’S Limited Warranty for
Top Page Image Contents