Cub Cadet 933 SWE, 930 SWE warranty Your Responsibility, 53% %842! #!54/ %. /0%2!4, 352&!#%3

Page 3

$!.'%2

$!.'%2

+%%0 !7!9 &2/- 2/4!4).' )-0%,,%2

 

 

 

 

 

 

!.$ !5'%2 #/.4!#4 7)4( )-0%,,%2 /2

 

 

 

!5'%2'#!.2!-054!4% (!.$3 !.$ &%%4

 

 

 

 53% #,%!./54 4//, 4/ 5.#,/'

 

 

 

$)3#(!2'% #(54%

 

 

 

 $)3%.'!'% #,54#( ,%6%23 34/0 %.').%

 

 

 

!.$.2%-!). "%().$)(!.$,%3%5.4),.!,,

 

 

 

-/6).' 0!243 (!6% 34/00%$ "%&/2%

 

 

 

5.#,/'').' /2 3%26)#).' -!#().%

 

 

 

 4/ !6/)$ 4(2/7. /"*%#43 ).*52)%3

 

 

 

.%6%26$)2%#4 $)3#(!2'% !44"934!.$%23

 

 

 

53% %842! #!54)/. 7(%. /0%2!4).' /.

!6/)$)).*5299&2/-

'2!6%, 352&!#%3

2/4!4).' !5'%2

 2%!$ /0%2!4/2g3 -!.5!,

+%%0 (!.$3 &%%4

 

 

#,%!./54 4//,

!.$ #,/4().' !7!9

$!.'%2

.%6%260542(!.$ ).4#(54% #/.4!#4#7)4( 2/4!4).' 0!243 #!. !-054!4% &).'%23 !.$ (!.$3

3(54 /&& %.').% !.$ 7!)4 5.4), !,, -/6).' 0!243 (!6% 34/00%$ "%&/2% 5.#,/'').'

53% #,%!./54 4//, /2 7//$%. 34)#+ 4/ 5.#,/' $)3#(!2'% #(54%

A chute clean-out tool is fastened to the top of the auger housing with a mounting clip. The tool is designed to clear a chute assembly of ice and snow.

This item is fastened with a cable tie at the factory. Cut the cable tie before operating the snow thrower.

WARNING: Never use your hands to clear a clogged chute assembly. Shut off engine and remain behind handles until all moving parts have stopped before using the clean-out tool to clear the chute assembly.

1

Safety

Labels

WARNING

This symbol points out important safety instructions which, if not followed, could endanger the personal safety and/or property of yourself and others. Read and follow all instructions in this manual before at- tempting to operate this machine. Failure to comply with these instructions may result in personal injury. When you see this symbol.

HEED ITS WARNING!

Your Responsibility

Restrict the use

of this power machine to persons who read, understand

and follow the warnings and instructions

in this manual

and on the machine.

Image 3
Contents Two Stage Snow Thrower Models 930 SWE & 933 SWE 31AE9PSV710 31AE9LSU710 31AE9LSU75628/06 Table of Contents Finding and Recording Model NumberCustomer Support  2%!$ /0%2!4/2g3 -!.5!, Your Responsibility53% %842! #!54/ %. /0%2!4 %, 352&!#%3Your Responsibility Restrict the use TrainingPreparationYour Responsibility Maintenance & StorageOperation Do not modify engineSetting Up Your Snow Thrower Shear Pin Storage Final Adjustments Testing Drive Control & Shift LeverTesting Auger Drive Control Reattach the spring to the actuator bracket Adjusting Drive and Auger ControlsAdjust the lock nut as follows Tire Pressure Pneumatic TiresKnow Your Snow Thrower Operating Your Snow Thrower$26% #/.42 Recoil Starter Gas & Oil Fill-UpStarting The Engine Electric StarterTo Engage Augers Chute Clean-Out ToolStopping The Engine To Engage DriveDrive Control Making AdjustmentsShift Cable Chute ControlAuger Control Wheel Making AdjustmentsChute Bracket Adjustment Skid ShoesAugers Maintaining Your Snow ThrowerEngine LubricationAuger Belt Shave Plate Skid ShoesShave Plate Replacing BeltsPlug, and ground Against engine before Performing any type Maintenance on Your machineAlways stop engine Disconnect sparkDrive Belt Hex Shaft Changing Friction WheelSecure with the cupped washer and hex bolt removed earlier Hub Assembly Friction WheelShort-Term Storage Off-Season StoragePreparing Engine Preparing Snow ThrowerTrouble- shooting Problem Cause RemedyFor further details Contact an authorized Service center This section addresses minor service issuesModels 930 SWE & 933 SWE Parts, call the Customer Dealer Referral Line at Parts ListTo order replacement Or visitModels 930 SWE & 933 SWE Steering Control 79 8 9878 79 710-0237 Screw, 5/16-24 x From previous Contact MTD Products Limited, Kitchener, on N2G 4J1, or call U.S.A CanadaMANUFACTURER’S Limited Warranty for