Boston Acoustics VSi H470T2, HSi H460T2 manual Installation Instructions, Diagram #4, Diagram #5

Page 14

Installation

Instructions

WARNING

Always turn off the amplifier or receiver when connecting speakers or any other components to the system.

Important

Installation should only be performed by professional installers or those possessing skills in construction, experience with the proper use of hand and power tools, knowledge of local building and electrical codes, and familiarity with the environment in which the speaker will be installed. Install the speaker to meet all local building, energy, and electrical codes.

Tools You’ll Need

A utility knife, jigsaw, or other tool for cutting the required hole in the mounting surface.

A #2 Phillips screwdriver.

A wire cutter or stripper for preparing the speaker wires.

A pencil.

Retrofit Installations

1.Mark the outline of the installation hole using the supplied template (see diagram #4). Make a small hole at the center of the speaker location. Insert a long bent piece of wire and rotate to confirm that there are no obstructions behind the chosen location (see diagram #5).

Instrucciones de instalación

ADVERTENCIA

Apague el amplificador o el receptor siempre que vaya a conectarlo los altavoces o a cualquier otro compo- nente del sistema.

Importante

La instalación sólo deben realizarla instaladores profesionales o aquellas personas con habilidades suficientes en la construcción, experiencia en el uso correcto de las herramientas de mano y eléctricas, conocimiento de las normas locales de construcción y eléctricos, y familiaridad con el entorno en que va a instalarse el altavoz de graves. Instale el altavoz T2 de modo que se cumplan todas las normas de construcción, energía y eléctricas locales.

Herramientas necesarias

Una navaja multiuso, sierra de vaivén u otra herramienta para cortar el orificio que se necesita en la superficie de instalación.

Un destornillador Phillips nº 2.

Un cortador de alambre o sepa- rador para preparar los cables del altavoz.

Un lapicero.

Instalaciones adaptadas

1.Marque el perfil del orificio de instalación usando la plantilla que se incluye (consulte el cro- quis nº 4). Realice un pequeño orificio en el centro del lugar en que vaya a colocarse el altavoz. Inserte un trozo largo de cable doblado y gírelo para confirmar que no hay obstrucciones detrás de la colocación elegida (con- sulte el croquis nº 5).

Instructions d’installation

AVERTISSEMENT

Eteignez toujours l’amplificateur ou le récepteur lorsque vous allez connecter des enceintes ou d’autres composants au système.

Important

L’installation ne devrait être exécutée que par des installateurs profession- nels ou par des personnes ayants des talents en construction, de l’expéri- ence avec l’utilisation correcte d’outils, des connaissances concernant les consignes locales de construction et de sécurité électrique et la connais- sance de l’environnement dans lequel l’enceinte T2 sera installée. Installez l’enceinte T2 conformément aux direc- tives locales de construction, d’énergie et électriques.

Outils dont vous aurez besoin

Un couteau de travail, une scie sauteuse ou un autre outil pour découper la cavité requise dans la surface de montage.

Tournevis Phillips #2.

Des pinces d’électricien ou des pinces à dénuder pour la prépa- ration des câbles.

Un stylo.

Installations existantes

1.Marquez le contour de la cavité d’installation à l’aide du gabarit fourni (voir diagramme 4). Percez un petit trou au centre de l’em- placement de l’enceinte. Insérez- y un long fil de fer plié et faites-le tourner afin de confirmer qu’il n’y a pas d’obstacles derrière l’em- placement choisi (voir dia- gramme 5).

Anleitungen zur Installation

ACHTUNG

Den Verstärker oder Receiver beim Anschließen der Lautsprecher oder irgend einer anderen Komponente immer ausschalten.

Wichtig

Die Installation sollte nur von profes- sionellem Personal oder von Personen vorgenommen werden, die ausre- ichend einschlägige Erfahrung haben, im Umgang mit Hand- und Elektro- werkzeug erfahren sind, die mit den elektrischen und bautechnischen Ver- ordnungen sowie mit der Umgebung vertraut sind, wo die T2-Lautsprecher installiert werden sollen. Die T2- Lautsprecher gemäß der geltenden bautechnischen, energie- und stromtechnischen Verordnungen installieren.

Erforderliches Werkzeug

Ein Messer, eine Säge oder ein anderes Werkzeug zum Aus- schneiden der Einbauöffnung.

Kreuzschlitzschraubendreher Nr. 2.

Ein Drahtschneider oder eine Abisolierzange.

Ein Bleistift.

Nachrüstungen

1.Den Umriss der Installations- öffnung mit Hilfe der beigeliefer- ten Schablone markieren (siehe Abb. 4). Ein kleines Loch in der Mitte der Lautsprecher-Einbau- öffnung bohren. Ein langes gebogenes Stück Draht in das Loch einführen und drehen, um sicherzustellen, dass hinter der Einbaustelle keine Hindernisse vorhanden sind (siehe Abb. 5).

 

 

 

 

Diagram #4

 

 

 

 

2.

Cut the installation hole.

2.

Corte el orificio de instalación.

3.

Run the wire from the amplifier

3.

Coloque el cable desde la colo-

 

location to the cutout. Allow for

 

 

cación del amplificador hasta el

 

an extra foot (300mm) of wire at

 

 

recorte. Deje cable sobrante (300

 

the cutout.

 

 

mm) en el recorte.

Diagram #5

2.Découpez le trou d’installation.

3.Acheminez le câble depuis l’am- plificateur jusqu’au trou découpé. Laissez dépasser le câble d’environ 300 mm (1 pied) du trou.

2.Die Einbauöffnung aussägen.

3.Das Kabel vom Verstärker bis zur Ausschnittstelle ziehen. Etwa 30 cm Kabel an der Ausschnittstelle zugeben.

– 14 –

Image 14
Contents HSi H460T2 VSi H470T2 Page Introducción Contents Contenido SommaireIntroduction EinführungSpecifications Thank you ¡Gracias MerciSingle Speaker Option #1 Option #2 Diffuse Mode T2 Dispersion Pattern Surround Placement Option #1 Surround Placement Option #2Surround Placement Option #3 Surround Placement Option #3Surround Placement Option #4 Surround Placement Option #4Surround Placement Option #5 Surround Placement Option #5Surround Placement Option #6 Surround Placement Option #6Installation Tips Diagram #1Transformers Bass ManagementOptional Brackets for New Construction To Remove GrilleDiagram #2 Altavoz ambiental Diagram #3Surround Speaker Enceinte SurroundDiagram #5 Installation InstructionsDiagram #4 Diagram #6 Diagram #7See diagram #9 Diagram #8Diagram #9 Pintura Diagram #10Painting PeintureDemande de service après-vente Power Handling Listening LevelsIf Service Seems Necessary Power Handling/HörpegelFor EU Customers Only Incorrecta Nation incorrecteBostonacoustics.com

VSi H470T2, HSi H460T2 specifications

Boston Acoustics has long been recognized for its commitment to delivering exceptional audio performance, and the HSi H460T2 and VSi H470T2 speakers showcase this tradition beautifully. Designed for both home theater and music applications, these speakers offer impressive sound quality, advanced technologies, and elegant design that blends seamlessly into any environment.

The HSi H460T2 is a high-performance in-wall speaker that excels in delivering detailed and dynamic audio. Featuring a 6.5-inch polypropylene cone woofer, this speaker produces powerful low frequencies while ensuring clarity in the midrange. It is equipped with a 1-inch soft dome tweeter that extends high frequencies, providing an expansive soundstage and crisp highs that are essential for both music and movie soundtracks. The speaker's dual voice coil design allows for versatile wiring configurations, enhancing its compatibility with various audio systems. One of the standout characteristics of the H460T2 is its paintable grill, enabling users to customize its appearance to match their interior decor.

On the other hand, the VSi H470T2 is an outstanding choice for those seeking a high-quality floor-standing speaker. This model features a dual 6.5-inch woofer configuration, delivering enriched bass response and a full-bodied sound. Adding to the depth of audio experience are the dual 1-inch titanium tweeters, designed for accurate reproduction of high frequencies, ensuring that vocals and instruments are reproduced with precision. The VSi H470T2 also includes innovative technologies such as Boston’s patented Venturi Bass Technology, which minimizes turbulence and enhances low-end performance.

Both models incorporate advanced engineering techniques that aim to minimize distortion and deliver clear, immersive sound. The design philosophy adopted by Boston Acoustics emphasizes not only acoustic performance but also aesthetic appeal. The enclosures are constructed from high-quality materials, engineered to reduce resonance and unwanted coloration, thereby enhancing the listening experience.

Whether you are setting up a home theater system or creating a high-fidelity audio space, the Boston Acoustics HSi H460T2 and VSi H470T2 speakers represent a formidable choice. Their combination of technology, design, and performance ensures that users can enjoy an enriching audio experience, making every listening session a delight. With Boston Acoustics’ legacy of excellence, these speakers are a testament to their dedication to sound quality and innovation.