Craftsman 536.88644 To Stop Your Snow Thrower, HOW to Move Forward and Backward, To Throw Snow

Page 12

The operation of any snow thrower can result in foreign objects being thrown into the eyes, which can result in se- vere eye damage. Always wear safety

glasses or eye shields while operating the snow thrower.

We recommend standard safety

glasses or a wide vision safety mask for over your glasses.

Manual before operating

_ARNING: Read Owner's machine. Never direct dis-

charge toward bystanders stop the engine before unclogging discharge chute or auger housing and before leaving the machine.

TO STOP YOUR

SNOW THROWER

. To stop throwing snow, release the aug_r drive lever. See Figure 10.

. To stop the wheels, release the traction drive lever.

3.To stop the engine, push the throttle control lever to off and pull out the ignition key.

TO CONTROL SNOW DISCHARGE

1.Turn the chute control rod to set the direction of the snow throwing.

2.Loosen the wing knob on the chute deflector and move the deflector to

set the distance. Move the deflector (Up) for more distance, (Down) for less distance. Then tighten the wing knob (See Figure 11).

Figure 11

HOW TO MOVE FORWARD AND BACKWARD

1.To shift, release the traction drive lever (left hand) and move the speed shifter lever to the speed you desire. Ground speed is deter- mined by snow conditions. Select

the speed you desire by moving the speed shifter lever left into the ap- propriate notches on the shift lever plate:

Speeds 1,2 - Wet, Heavy

Speed 3 - Light

Speed 4 - Very Light

Speed 5,6 - Transport only

2.Engage the traction drive lever (left hand). As the snow thrower starts to move, maintain a firm hold on the handles, and guide the snow throw- er along the clearing path. Do not attempt to push the snow thrower.

3.To move the snow thrower back- ward, move the speed shifter lever right into first or second reverse and engage the traction drive lever (left hand).

IMPORTANT: Do not move the speed shifter lever while the traction lever is down.

TO THROW SNOW

1.Push down the auger driver lever (right hand).

2.Release to stop throwing snow.

TO USE WHEEL LOCKOUT PIN

. The left hand wheel is secured to

the axle with a klick pin. This unit was shipped with this klick pin in the locked position (through wheel hole). See Figure 12.

Klick Pin

Locked

Position

2-Wheel Drive

Figure 12

. For ease of maneuverability in light snow conditions, disconnect the klick pin from the wheel locked position and push into the single wheel drive position (unlocked axle hole only). See Figure 13.

F-O01087J12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Icrrftsmrni 001087JEspanol Wash Hands After HandlingTraining PreparationMaintenance and Storage Do not attempt to use snow thrower on a roofSafetyWarningSymbols SplitLockwasher 11/324-20 Tools Required for Assembly ThrowerTo Remove Snow Thrower From Carton Remove from the carton Place until needed for storageTo Assemble the Handle and Crank Assembly Caught between the upper and lower handleLoosen, but do not To Install Shifter Knob Pin. Spread ends of cotter pin toUniversal DriveSnow Chute Assembly ChecklistHOW to SET the Skid Height Service And Adjustment sectionKnow Your Snow Thrower Choke Control Used to start a coldHOW to Move Forward and Backward To Stop Your Snow ThrowerTo USE Wheel Lockout PIN To Control Snow DischargeBefore Starting the Engine Fill GASDicates that alcohol blended To Stop Engine To Start EngineElectric starter, if equipped Cold StartDo not prime if temperature above 50 F 10 C Warm StartEngine runs smoothly, move choke lever to No Choke Position Frozen StarterSnow Throwing Tips 001087J16Lubrication Chart Customer ResponsibilitiesGeneral Recommendations After Each USEProduct Specifications AS RequiredLUBRICATION-EVERY 25 Hours Wheel and disc drive plateLubrication To Change Engine OILSpark Plug 001087J19To Adjust Skid Height To Adjust Scraper BARHOW to Check and Adjust Cables To Adjust BeltsDrive Lever How To Remove The Auger Drive Belt To Replace BeltsTraction Drive Belt Side/ %Outdoors, away from fire or Traction Drive BeltBelt AugerHOW to Adjust or Replace the Friction Wheel HOW to Adjust the Belt GuideHow To Check The Friction Wheel Remove Top Bolt each sideHow To Replace The Friction Wheel HOW to Replace the Auger Shear Bolt To Adjust the CarburetorTo Adjust or Replace the Spark Plug To adjustTo Replace Thoroughly clean the snow thrower EngineOther Provide maximum performance for the next seasonCause TroubleDifficult starting CorrectionFrame Assembly ScrewWasher 001087J30Electric Start Assembly Motor StarterIdler Assembly Frame AssyCOVER, Bottom Gear Case Assembly Case GearSEAL, OIL BearingDrive Components 190 191217 255245 246247 249Auger Housing Assembly 5OO48O PULLEY, 4L 6.12X 9517 711862 9357 301380-853 340720 710026 760875Discharge Chute Assembly CraftsmanWasher Plastic Handle Assembly OO1087J4073O 756Wheel Assembly 671 655 650 678Shift Yoke Assembly 791 792 8812Chute Control ROD Assembly 867866 Decal Drive Clutch Symbol Decal Auger Clutch SymbolModel Plate Decal Chute HandCraftsman 4-CYCLE Engine Model Number KEY Part NO. no KEY Part Description RPM650139 27677ALill Ill KEY PartIOA 33290E Electric Starter Volt Retainer RingSpring Retainer Anti-drift SpringOO1087J52 KEY Part Description Part Idhhhh

536.88644 specifications

The Craftsman 536.88644 is a versatile snow blower designed to tackle the challenges of winter weather with efficiency and ease. As part of the Craftsman lineup, this machine exemplifies the brand's commitment to quality, performance, and user satisfaction.

One of the standout features of the Craftsman 536.88644 is its powerful engine. Equipped with a reliable 24-inch clearing width, the snow blower can efficiently handle heavy snowfall, making it an ideal choice for homeowners in areas that experience significant winter weather. The engine delivers robust performance, allowing the machine to handle not only light dustings but also deeper snow accumulations.

The Craftsman 536.88644 features a self-propelling system, which ensures that users can effortlessly maneuver the machine across various terrains. The adjustable speed settings offer flexibility, enabling users to customize their pace based on the snow conditions and their own preferences. This feature is particularly beneficial during heavy snowfall, where control and direction become crucial.

An additional innovative technology integrated into the design is the 180-degree chute rotation. This allows users to easily direct snow away from walkways, driveways, and parked vehicles, providing optimal snow management. The chute can be adjusted with a simple crank, making it user-friendly and efficient for rapid snow clearing tasks.

Durability is a key characteristic of the Craftsman 536.88644. Built with robust materials, it is engineered to withstand the rigors of winter use. The reinforced auger and impeller design not only enhances durability but also increases the machine's snow-throwing capability, allowing it to throw snow up to 40 feet away.

User comfort is also a consideration in the design of this snow blower. The ergonomically designed controls and comfortable grip handles reduce fatigue during operation, while the heated hand grips provide warmth during cold winter days. This thoughtful design ensures that users can operate the Craftsman 536.88644 for extended periods without discomfort.

Overall, the Craftsman 536.88644 combines power, versatility, and user-friendly features to create a reliable snow-clearing solution. With its robust performance, thoughtful design, and durable construction, this snow blower is well-suited for homeowners seeking to maintain clear pathways and driveways during the winter months. Whether faced with light snowfall or heavy blizzards, the Craftsman 536.88644 ensures efficient and effective snow removal.
Top Page Image Contents