Craftsman 536.88644 manual Engine, Other, Thoroughly clean the snow thrower

Page 28

snow thrower indoors or in

_ARNING: Never store your an enclosed, poorly venti-

lated area. If gasoline remains in the tank, fumes may reach an open flame, spark or pilot light from a fur- nace, water heater, clothes dryer, cigarette, etc.

NOTE: To prevent engine damage (if snow thrower is not used for more than

30 days) follow the steps below.

SNOW THROWER

1.Thoroughly clean the snow thrower.

2.Lubricate all lubrication points. See the Maintenance section.

,Be sure that all nuts, bolts and screws are securely fastened. In- spect all visible moving parts for damage, breakage and wear. Re- place if necessary.

4.Touch up all rusted or chipped paint surfaces; sand lightly before paint- ing.

. Cover the bare metal parts of the blower housing auger and the im- peller with rust preventative, such as a spray lubricant.

NOTE: A yearly checkup or tune-up by a Sears service center is a good way of ensuring that your snow thrower will

provide maximum performance for the next season.

ENGINE

line outdoors, away from

_ARNING: Drain the gaso- fire or flame.

Gasoline must be removed or treated to prevent gum deposits from forming in the fuel tank, filter, hose, and carburetor during storage. Also, during storage al- cohol blended gasoline that uses etha- nol or methanol (sometimes called gasohol) attracts water. It acts on the gasoline to form acids which damage the engine.

. To remove gasoline, run the engine until the fuel tank is empty and the engine stops.

. If you do not remove the gasoline, use fuel stabilizer supplied with unit or purchase Craftsman Fuel Stabi- lizer No. 3550. Add fuel stabilizer to any gasoline left in the tank to mini- mize gum deposits and acids. If the fuel tank is almost empty, mix stabi- lizer with fresh gasoline in a sepa- rate container and add some to the fuel tank.

. Always follow the instruction on the stabilizer container. After the stabi- lizer is added to the fuel tank, run the engine at least ten minutes to allow the mixture to reach the car- buretor.

. Change the engine oil.

5.Lubricate the piston/cylinder area. First, remove the spark plug and squirt a few drops of clean engine oil into the spark plug hole. Next, cover the spark plug hole with a rag to absorb oil spray. Then, pull two or three times on the recoil starter rope to rotate the engine. Finally, install the spark plug and attach the spark plug wire.

OTHER

1.If possible, store your snow thrower indoors and cover it to give protec- tion from dust and dirt.

2.If the machine must be stored out- doors, block up the snow thrower to be sure the entire machine is off the ground.

3.Cover the snow thrower with a suit- able protective cover that does not retain moisture. Do not use plastic.

IMPORTANT: Never cover snow

thrower while engine and exhaust areas are still warm.

F-001087J28

Page 27 Page 29
Image 28
Page 27 Page 29
Contents Icrrftsmrni 001087JEspanol Wash Hands After HandlingTraining PreparationMaintenance and Storage Do not attempt to use snow thrower on a roofSafetyWarningSymbols 11/32 SplitLockwasher4-20 Tools Required for Assembly ThrowerTo Remove Snow Thrower From Carton Remove from the carton Place until needed for storageCaught between the upper and lower handle To Assemble the Handle and Crank AssemblyLoosen, but do not To Install Shifter Knob Pin. Spread ends of cotter pin toUniversal DriveSnow Chute Assembly ChecklistHOW to SET the Skid Height Service And Adjustment sectionKnow Your Snow Thrower Choke Control Used to start a coldHOW to Move Forward and Backward To Stop Your Snow ThrowerTo USE Wheel Lockout PIN To Control Snow DischargeFill GAS Before Starting the EngineDicates that alcohol blended To Stop Engine To Start EngineElectric starter, if equipped Cold StartDo not prime if temperature above 50 F 10 C Warm StartEngine runs smoothly, move choke lever to No Choke Position Frozen StarterSnow Throwing Tips 001087J16Lubrication Chart Customer ResponsibilitiesGeneral Recommendations After Each USEProduct Specifications AS RequiredLUBRICATION-EVERY 25 Hours Wheel and disc drive plateLubrication To Change Engine OILSpark Plug 001087J19To Adjust Skid Height To Adjust Scraper BARTo Adjust Belts HOW to Check and Adjust CablesDrive Lever How To Remove The Auger Drive Belt To Replace BeltsTraction Drive Belt Side/ %Outdoors, away from fire or Traction Drive BeltBelt AugerHOW to Adjust or Replace the Friction Wheel HOW to Adjust the Belt GuideHow To Check The Friction Wheel Remove Top Bolt each sideHow To Replace The Friction Wheel HOW to Replace the Auger Shear Bolt To Adjust the CarburetorTo Adjust or Replace the Spark Plug To adjustTo Replace Thoroughly clean the snow thrower EngineOther Provide maximum performance for the next seasonCause TroubleDifficult starting CorrectionFrame Assembly ScrewWasher 001087J30Electric Start Assembly Motor StarterFrame Assy Idler AssemblyCOVER, Bottom Gear Case Assembly Case GearSEAL, OIL BearingDrive Components 190 191217 255245 246247 249Auger Housing Assembly 5OO48O PULLEY, 4L 6.12X 9517 711862 9357 301380-853 340720 710026 760875Discharge Chute Assembly CraftsmanWasher Plastic Handle Assembly OO1087J4073O 756Wheel Assembly 671 655 650 678Shift Yoke Assembly 791 792 8812867 Chute Control ROD Assembly866 Decal Drive Clutch Symbol Decal Auger Clutch SymbolModel Plate Decal Chute HandCraftsman 4-CYCLE Engine Model Number KEY Part NO. no KEY Part Description RPM650139 27677ALill Ill KEY PartIOA 33290E Electric Starter Volt Retainer RingSpring Retainer Anti-drift SpringOO1087J52 KEY Part Description Part Idhhhh

536.88644 specifications

The Craftsman 536.88644 is a versatile snow blower designed to tackle the challenges of winter weather with efficiency and ease. As part of the Craftsman lineup, this machine exemplifies the brand's commitment to quality, performance, and user satisfaction.

One of the standout features of the Craftsman 536.88644 is its powerful engine. Equipped with a reliable 24-inch clearing width, the snow blower can efficiently handle heavy snowfall, making it an ideal choice for homeowners in areas that experience significant winter weather. The engine delivers robust performance, allowing the machine to handle not only light dustings but also deeper snow accumulations.

The Craftsman 536.88644 features a self-propelling system, which ensures that users can effortlessly maneuver the machine across various terrains. The adjustable speed settings offer flexibility, enabling users to customize their pace based on the snow conditions and their own preferences. This feature is particularly beneficial during heavy snowfall, where control and direction become crucial.

An additional innovative technology integrated into the design is the 180-degree chute rotation. This allows users to easily direct snow away from walkways, driveways, and parked vehicles, providing optimal snow management. The chute can be adjusted with a simple crank, making it user-friendly and efficient for rapid snow clearing tasks.

Durability is a key characteristic of the Craftsman 536.88644. Built with robust materials, it is engineered to withstand the rigors of winter use. The reinforced auger and impeller design not only enhances durability but also increases the machine's snow-throwing capability, allowing it to throw snow up to 40 feet away.

User comfort is also a consideration in the design of this snow blower. The ergonomically designed controls and comfortable grip handles reduce fatigue during operation, while the heated hand grips provide warmth during cold winter days. This thoughtful design ensures that users can operate the Craftsman 536.88644 for extended periods without discomfort.

Overall, the Craftsman 536.88644 combines power, versatility, and user-friendly features to create a reliable snow-clearing solution. With its robust performance, thoughtful design, and durable construction, this snow blower is well-suited for homeowners seeking to maintain clear pathways and driveways during the winter months. Whether faced with light snowfall or heavy blizzards, the Craftsman 536.88644 ensures efficient and effective snow removal.
Top Page Image Contents