Craftsman 536.88644 manual To Adjust Skid Height, To Adjust Scraper BAR

Page 20

nect the spark plug wire and

_lb ARNING: Always discon- place it where it cannot

make contact with spark plug to pre- vent accidental starting when mak- ing any adjustments or repairs.

TO ADJUST SKID HEIGHT

This snow thrower is equipped with two height adjustment skids, located on the outside of the auger housing. See

Figure 19.

These skids elevate the front of the snow thrower.

Mountinq Nuts

Auger Housing Height Adjust Skid

Figure 19

For normal hard surfaces, such as a

paved driveway or walk, adjust the skids as follows.

1.Position the snow thrower on a level surface.

2.Make sure both tires are equally in- flated. Proper tire pressure is 14 to 17 PSI. See side of tire for maxi- mum inflation. Do not exceed side- wall maximum pressure on tire.

3.Place the extra shear bolts supplied (found in parts bag) under each end of the scraper bar next to the adjustable skids.

4.Loosen the mounting nuts that hold the adjustable skids. To bring the front of the snow thrower down,

raise the adjustable skids. Tighten the mounting nuts. See Figure 19.

NOTE: For rocky or uneven surfaces, raise the front of the snow thrower by moving the skids down.

maintain proper ground

,_ WARNING: Be certain to clearance for your particular

area to be cleared. Objects such as gravel, rocks or other debris, if struck by the impeller, may be thrown with sufficient force to cause

personal injury, property damage or damage to the snow thrower.

TO ADJUST SCRAPER BAR

After considerable use, the metal scrap- er bar will have a definite wear pattern. The scraper bar in conjunction with the skids should always be adjusted to al- low 1/8" between the scraper bar and the sidewalk or area to be cleaned.

1.Position the snow thrower on a level surface.

. Make sure both tires are equally in- flated. Proper tire pressure is 14 to 17 PSI. See side of tire for maxi- mum inflation. Do not exceed side- wall maximum pressure on tire.

3.Loosen the carriage bolts and nuts securing the scraper bar to the au- ger housing.

4.Adjust the scraper bar to the proper position.

5.Tighten the carriage bolts and nuts, making sure that the scraper bar is parallel with the working surface.

. For extended operation, the scraper bar may be reversed. If the scraper bar must be replaced due to wear, remove the carriage bolts and nuts and install a new scraper bar.

F-001087J20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Icrrftsmrni 001087JEspanol Wash Hands After HandlingTraining PreparationMaintenance and Storage Do not attempt to use snow thrower on a roofSafetyWarningSymbols 4-20 SplitLockwasher11/32 Tools Required for Assembly ThrowerTo Remove Snow Thrower From Carton Remove from the carton Place until needed for storageLoosen, but do not To Assemble the Handle and Crank AssemblyCaught between the upper and lower handle To Install Shifter Knob Pin. Spread ends of cotter pin toUniversal DriveSnow Chute Assembly ChecklistHOW to SET the Skid Height Service And Adjustment sectionKnow Your Snow Thrower Choke Control Used to start a coldHOW to Move Forward and Backward To Stop Your Snow ThrowerTo USE Wheel Lockout PIN To Control Snow DischargeDicates that alcohol blended Before Starting the EngineFill GAS To Stop Engine To Start EngineElectric starter, if equipped Cold StartDo not prime if temperature above 50 F 10 C Warm StartEngine runs smoothly, move choke lever to No Choke Position Frozen StarterSnow Throwing Tips 001087J16Lubrication Chart Customer ResponsibilitiesGeneral Recommendations After Each USEProduct Specifications AS RequiredLUBRICATION-EVERY 25 Hours Wheel and disc drive plateLubrication To Change Engine OILSpark Plug 001087J19To Adjust Skid Height To Adjust Scraper BARDrive Lever HOW to Check and Adjust CablesTo Adjust Belts How To Remove The Auger Drive Belt To Replace BeltsTraction Drive Belt Side/ %Outdoors, away from fire or Traction Drive BeltBelt AugerHOW to Adjust or Replace the Friction Wheel HOW to Adjust the Belt GuideHow To Check The Friction Wheel Remove Top Bolt each sideHow To Replace The Friction Wheel HOW to Replace the Auger Shear Bolt To Adjust the CarburetorTo Adjust or Replace the Spark Plug To adjustTo Replace Thoroughly clean the snow thrower EngineOther Provide maximum performance for the next seasonCause TroubleDifficult starting CorrectionFrame Assembly ScrewWasher 001087J30Electric Start Assembly Motor StarterCOVER, Bottom Idler AssemblyFrame Assy Gear Case Assembly Case GearSEAL, OIL BearingDrive Components 190 191217 255245 246247 249Auger Housing Assembly 5OO48O PULLEY, 4L 6.12X 9517 711862 9357 301380-853 340720 710026 760875Discharge Chute Assembly CraftsmanWasher Plastic Handle Assembly OO1087J4073O 756Wheel Assembly 671 655 650 678Shift Yoke Assembly 791 792 8812866 Chute Control ROD Assembly867 Decal Drive Clutch Symbol Decal Auger Clutch SymbolModel Plate Decal Chute HandCraftsman 4-CYCLE Engine Model Number KEY Part NO. no KEY Part Description RPM650139 27677ALill Ill KEY PartIOA 33290E Electric Starter Volt Retainer RingSpring Retainer Anti-drift SpringOO1087J52 KEY Part Description Part Idhhhh

536.88644 specifications

The Craftsman 536.88644 is a versatile snow blower designed to tackle the challenges of winter weather with efficiency and ease. As part of the Craftsman lineup, this machine exemplifies the brand's commitment to quality, performance, and user satisfaction.

One of the standout features of the Craftsman 536.88644 is its powerful engine. Equipped with a reliable 24-inch clearing width, the snow blower can efficiently handle heavy snowfall, making it an ideal choice for homeowners in areas that experience significant winter weather. The engine delivers robust performance, allowing the machine to handle not only light dustings but also deeper snow accumulations.

The Craftsman 536.88644 features a self-propelling system, which ensures that users can effortlessly maneuver the machine across various terrains. The adjustable speed settings offer flexibility, enabling users to customize their pace based on the snow conditions and their own preferences. This feature is particularly beneficial during heavy snowfall, where control and direction become crucial.

An additional innovative technology integrated into the design is the 180-degree chute rotation. This allows users to easily direct snow away from walkways, driveways, and parked vehicles, providing optimal snow management. The chute can be adjusted with a simple crank, making it user-friendly and efficient for rapid snow clearing tasks.

Durability is a key characteristic of the Craftsman 536.88644. Built with robust materials, it is engineered to withstand the rigors of winter use. The reinforced auger and impeller design not only enhances durability but also increases the machine's snow-throwing capability, allowing it to throw snow up to 40 feet away.

User comfort is also a consideration in the design of this snow blower. The ergonomically designed controls and comfortable grip handles reduce fatigue during operation, while the heated hand grips provide warmth during cold winter days. This thoughtful design ensures that users can operate the Craftsman 536.88644 for extended periods without discomfort.

Overall, the Craftsman 536.88644 combines power, versatility, and user-friendly features to create a reliable snow-clearing solution. With its robust performance, thoughtful design, and durable construction, this snow blower is well-suited for homeowners seeking to maintain clear pathways and driveways during the winter months. Whether faced with light snowfall or heavy blizzards, the Craftsman 536.88644 ensures efficient and effective snow removal.
Top Page Image Contents