Craftsman 536.88644 To Stop Engine, To Start Engine, Electric starter, if equipped, Cold Start

Page 14

Never use engine or carburetorcleaner

products in the fuel tank or permanent damage may occur.

1.Fill the fuel tank only with a fresh, clean, unleaded regular, unleaded premium, or reformulated automo- tive gasoline. DO NOT use leaded gasoline. Make sure that the con-

tainer you pour the gasoline from is clean and free from rust or other for-

eign particles. Never use gasoline that may be stale from long periods of storage in the container.

mable. Always use caution

,_ WARNING: Gasoline is flam- when handling or storing

gasoline.

Do not fill fuel tank while snow

thrower is running, when it is hot, or when snow thrower is in an en-

closed area.

Keep away from open flame or an electrical spark and do not smoke while filling the fuel tank.

Never fill the tank completely. Fill the tank to within 1/4"-1/2" from the

top to provide space for expansion of fuel.

Always fill fuel tank outdoors and use a funnel or spout to prevent spilling.

Make sure to wipe up any spilled fuel before stating the engine. Store gasoline in a clean, approved

container and keep the cap in place on the container.

TO STOP ENGINE

To stop engine, move the throttle con- trol lever to "STOP" position and re- move key. Keep the key in a safe place. The engine will not start without the key.

TO START ENGINE

(electric starter, if equipped)

Be sure that the engine has sufficient

oil. The snow thrower engine is equipped with a 120 volt A.C. electric starter and recoil starter. Before start-

ing the engine, be certain that you have read the following information,

equipped with a three-wire

,_ WARNING: The starter is power cord and plug and is

designed to operate on 120 volt AC household current.It must be proper- ly grounded at all times to avoid the possibility of electrical shock which may be injurious to operator. Follow all instructions carefully as set forth in the "To Start Engine" section. De- termine that your house wiring is a three-wire grounded system. Ask a licensed electrician if you are not sure. If your house wire system is not a three-wire system, do not use this electric starter under any condi- tions. If your system is grounded and a three-hole receptacle is not available at the point your starter will normally be used, one should be installed by a licensed electrician. when connecting 120 volt AC "Power

Cord", always connect the cord to the Switch Box" on the engine first, then plug the other end into the three-hole grounded receptacle. When disconnecting "Power cord", always unplug the end in the three- hole grounded receptacle first.

COLD START

1.Be sure auger drive and traction drive levers are in the disengaged (RELEASED) position.

2.Move throttle control to"FAST' posi- tion.

3.Remove the keys form the plastic bag. Insert one key into ignition slot. Make sure it snaps into place.

Do not turn key. Keep the second key in a safe place.

4.Rotate choke knob clockwise to the choke ON position.

5.Connect the power cord to the switch box on the engine.

6.Plug other end of power cord into a three-hole, grounded 120 VOLT, AC receptacle. (See WARNING in this section).

F-001087J

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Icrrftsmrni 001087JEspanol Wash Hands After HandlingTraining PreparationMaintenance and Storage Do not attempt to use snow thrower on a roofSafetyWarningSymbols 4-20 SplitLockwasher11/32 To Remove Snow Thrower From Carton Tools Required for AssemblyThrower Remove from the carton Place until needed for storageLoosen, but do not To Assemble the Handle and Crank AssemblyCaught between the upper and lower handle Universal To Install Shifter KnobPin. Spread ends of cotter pin to DriveHOW to SET the Skid Height Snow Chute AssemblyChecklist Service And Adjustment sectionKnow Your Snow Thrower Choke Control Used to start a coldTo USE Wheel Lockout PIN HOW to Move Forward and BackwardTo Stop Your Snow Thrower To Control Snow DischargeDicates that alcohol blended Before Starting the EngineFill GAS Electric starter, if equipped To Stop EngineTo Start Engine Cold StartEngine runs smoothly, move choke lever to No Choke Position Do not prime if temperature above 50 F 10 CWarm Start Frozen StarterSnow Throwing Tips 001087J16General Recommendations Lubrication ChartCustomer Responsibilities After Each USELUBRICATION-EVERY 25 Hours Product SpecificationsAS Required Wheel and disc drive plateSpark Plug LubricationTo Change Engine OIL 001087J19To Adjust Skid Height To Adjust Scraper BARDrive Lever HOW to Check and Adjust CablesTo Adjust Belts Traction Drive Belt How To Remove The Auger Drive BeltTo Replace Belts Side/ %Belt Outdoors, away from fire orTraction Drive Belt AugerHow To Check The Friction Wheel HOW to Adjust or Replace the Friction WheelHOW to Adjust the Belt Guide Remove Top Bolt each sideHow To Replace The Friction Wheel To Adjust or Replace the Spark Plug HOW to Replace the Auger Shear BoltTo Adjust the Carburetor To adjustTo Replace Other Thoroughly clean the snow throwerEngine Provide maximum performance for the next seasonDifficult starting CauseTrouble CorrectionWasher Frame AssemblyScrew 001087J30Electric Start Assembly Motor StarterCOVER, Bottom Idler AssemblyFrame Assy SEAL, OIL Gear Case AssemblyCase Gear Bearing217 Drive Components190 191 255247 245246 249Auger Housing Assembly 5OO48O PULLEY, 4L 6.12X 9517 711862 9357 301380-853 340720 710026 760875Discharge Chute Assembly CraftsmanWasher Plastic Handle Assembly OO1087J4073O 756Wheel Assembly 671 655 650 678Shift Yoke Assembly 791 792 8812866 Chute Control ROD Assembly867 Model Plate Decal Drive Clutch SymbolDecal Auger Clutch Symbol Decal Chute HandCraftsman 4-CYCLE Engine Model Number KEY Part NO. no KEY Part Description RPM650139 27677ALill Ill KEY PartIOA Spring Retainer 33290E Electric Starter VoltRetainer Ring Anti-drift SpringOO1087J52 KEY Part Description Part Idhhhh

536.88644 specifications

The Craftsman 536.88644 is a versatile snow blower designed to tackle the challenges of winter weather with efficiency and ease. As part of the Craftsman lineup, this machine exemplifies the brand's commitment to quality, performance, and user satisfaction.

One of the standout features of the Craftsman 536.88644 is its powerful engine. Equipped with a reliable 24-inch clearing width, the snow blower can efficiently handle heavy snowfall, making it an ideal choice for homeowners in areas that experience significant winter weather. The engine delivers robust performance, allowing the machine to handle not only light dustings but also deeper snow accumulations.

The Craftsman 536.88644 features a self-propelling system, which ensures that users can effortlessly maneuver the machine across various terrains. The adjustable speed settings offer flexibility, enabling users to customize their pace based on the snow conditions and their own preferences. This feature is particularly beneficial during heavy snowfall, where control and direction become crucial.

An additional innovative technology integrated into the design is the 180-degree chute rotation. This allows users to easily direct snow away from walkways, driveways, and parked vehicles, providing optimal snow management. The chute can be adjusted with a simple crank, making it user-friendly and efficient for rapid snow clearing tasks.

Durability is a key characteristic of the Craftsman 536.88644. Built with robust materials, it is engineered to withstand the rigors of winter use. The reinforced auger and impeller design not only enhances durability but also increases the machine's snow-throwing capability, allowing it to throw snow up to 40 feet away.

User comfort is also a consideration in the design of this snow blower. The ergonomically designed controls and comfortable grip handles reduce fatigue during operation, while the heated hand grips provide warmth during cold winter days. This thoughtful design ensures that users can operate the Craftsman 536.88644 for extended periods without discomfort.

Overall, the Craftsman 536.88644 combines power, versatility, and user-friendly features to create a reliable snow-clearing solution. With its robust performance, thoughtful design, and durable construction, this snow blower is well-suited for homeowners seeking to maintain clear pathways and driveways during the winter months. Whether faced with light snowfall or heavy blizzards, the Craftsman 536.88644 ensures efficient and effective snow removal.
Top Page Image Contents