Craftsman 536.88644 manual Warm Start, Engine runs smoothly, move choke lever to No Choke Position

Page 15

. Push the primer button while cov- ering the vent hole as follows: Re- move finger from primer button between primes.

Do not prime if temperature above 50 ° F (10 ° C).

Push two time if temperature is 50 ° F (10 ° C) to 15°F (-10 ° C).

Push four times if temperature is below 15° F (-10 ° C).

8.Push down on the starter button until the engine starts. Do not crank for more than 10 seconds at a time. This electric starter is thermally pro- tected. If overheated it will stop au- tomatically and can be restarted only when it has cooled to a safe temperature (a wait of about 5 to 10 minutes is required).

9.When t_e engine starts, release the starter button and move choke le- ver to "1/2 choke" position. When

engine runs smoothly, move choke lever to "No Choke" Position.

10.Disconnect power cord from recep- tacle, first, and then from switch box.

NOTE: Allow the engine to warm up for several minutes before blowing snow in temperatures below 0°K

11.Run engine at full throttle "FAST' when throwing snow.

WARM START

If restarting a warm engine after a short shutdown, leave choke at "OFF" and do not push the primer button. If the en- gine fails to start, follow the Cold Start instructions.

TO START ENGINE

(recoil starter)

Be sure that the engine has sufficient oil. The snow thrower engine is equipped with a recoil starter. Before starting the engine, be certain that you have read the following information.

COLD START

,Be sure auger drive and traction drive levers are in the disengaged (RELEASED) position.

*Move throttle control to"FAST' posi- tion.

3.Remove the keys form the plastic bag. Insert one key into ignition slot. Make sure it snaps into place. Do not turn key. Keep the second key in a safe place.

4.Rotate choke knob clockwise to the choke ON position.

5.Push the primer button while cov- ering the vent hole as follows: Re- move finger from primer button between primes.

Do not prime if temperature above 50 ° F (10 ° C).

Push two time if temperature is 50 ° F (10 ° C) to 15°F (-10 ° C).

Push four times if temperature is below 15° F (-10 ° C).

6.Pull the starter handle rapidly. Do not allow the handle to snap back, but allow it to rewind slowly while keeping a firm hold on the starter handle.

,As the engine warms up, move choke lever to "1/2 choke" position.

When engine runs smoothly, move choke lever to "No Choke" Posi-

tion.

NOTE: Allow the engine to warm up for several minutes before blowing snow in temperatures below 0°F.

8.Run engine at full throttle "FAST' when throwing snow.

WARM START

If restarting a warm engine after a short shutdown, leave choke at "OFF" and do not push the primer button. If the en-

gine fails to start, follow the Cold Start instructions.

FROZEN STARTER

If the starter is frozen and will not turn engine:

1.Pull as much rope out of the starter as possible.

F--001087J15

Image 15
Contents 001087J IcrrftsmrniWash Hands After Handling EspanolPreparation TrainingDo not attempt to use snow thrower on a roof Maintenance and StorageSafetyWarningSymbols SplitLockwasher 11/324-20 Remove from the carton Place until needed for storage Tools Required for AssemblyThrower To Remove Snow Thrower From CartonTo Assemble the Handle and Crank Assembly Caught between the upper and lower handleLoosen, but do not Drive To Install Shifter KnobPin. Spread ends of cotter pin to UniversalService And Adjustment section Snow Chute AssemblyChecklist HOW to SET the Skid HeightChoke Control Used to start a cold Know Your Snow ThrowerTo Control Snow Discharge HOW to Move Forward and BackwardTo Stop Your Snow Thrower To USE Wheel Lockout PINBefore Starting the Engine Fill GASDicates that alcohol blended Cold Start To Stop EngineTo Start Engine Electric starter, if equippedFrozen Starter Do not prime if temperature above 50 F 10 CWarm Start Engine runs smoothly, move choke lever to No Choke Position001087J16 Snow Throwing TipsAfter Each USE Lubrication ChartCustomer Responsibilities General RecommendationsWheel and disc drive plate Product SpecificationsAS Required LUBRICATION-EVERY 25 Hours001087J19 LubricationTo Change Engine OIL Spark PlugTo Adjust Scraper BAR To Adjust Skid HeightHOW to Check and Adjust Cables To Adjust BeltsDrive Lever Side/ % How To Remove The Auger Drive BeltTo Replace Belts Traction Drive BeltAuger Outdoors, away from fire orTraction Drive Belt BeltRemove Top Bolt each side HOW to Adjust or Replace the Friction WheelHOW to Adjust the Belt Guide How To Check The Friction WheelHow To Replace The Friction Wheel To adjust HOW to Replace the Auger Shear BoltTo Adjust the Carburetor To Adjust or Replace the Spark PlugTo Replace Provide maximum performance for the next season Thoroughly clean the snow throwerEngine OtherCorrection CauseTrouble Difficult starting001087J30 Frame AssemblyScrew WasherMotor Starter Electric Start AssemblyIdler Assembly Frame AssyCOVER, Bottom Bearing Gear Case AssemblyCase Gear SEAL, OIL255 Drive Components190 191 217249 245246 2475OO Auger Housing Assembly9517 711862 9357 301380-853 340720 710026 760875 48O PULLEY, 4L 6.12XCraftsman Discharge Chute AssemblyWasher Plastic OO1087J40 Handle Assembly756 73O671 655 650 678 Wheel Assembly791 792 8812 Shift Yoke AssemblyChute Control ROD Assembly 867866 Decal Chute Hand Decal Drive Clutch SymbolDecal Auger Clutch Symbol Model PlateCraftsman 4-CYCLE Engine Model Number KEY Part Description RPM KEY Part NO. no27677A 650139KEY Part Lill IllIOA Anti-drift Spring 33290E Electric Starter VoltRetainer Ring Spring RetainerOO1087J52 KEY Part Description Idhhhh Part

536.88644 specifications

The Craftsman 536.88644 is a versatile snow blower designed to tackle the challenges of winter weather with efficiency and ease. As part of the Craftsman lineup, this machine exemplifies the brand's commitment to quality, performance, and user satisfaction.

One of the standout features of the Craftsman 536.88644 is its powerful engine. Equipped with a reliable 24-inch clearing width, the snow blower can efficiently handle heavy snowfall, making it an ideal choice for homeowners in areas that experience significant winter weather. The engine delivers robust performance, allowing the machine to handle not only light dustings but also deeper snow accumulations.

The Craftsman 536.88644 features a self-propelling system, which ensures that users can effortlessly maneuver the machine across various terrains. The adjustable speed settings offer flexibility, enabling users to customize their pace based on the snow conditions and their own preferences. This feature is particularly beneficial during heavy snowfall, where control and direction become crucial.

An additional innovative technology integrated into the design is the 180-degree chute rotation. This allows users to easily direct snow away from walkways, driveways, and parked vehicles, providing optimal snow management. The chute can be adjusted with a simple crank, making it user-friendly and efficient for rapid snow clearing tasks.

Durability is a key characteristic of the Craftsman 536.88644. Built with robust materials, it is engineered to withstand the rigors of winter use. The reinforced auger and impeller design not only enhances durability but also increases the machine's snow-throwing capability, allowing it to throw snow up to 40 feet away.

User comfort is also a consideration in the design of this snow blower. The ergonomically designed controls and comfortable grip handles reduce fatigue during operation, while the heated hand grips provide warmth during cold winter days. This thoughtful design ensures that users can operate the Craftsman 536.88644 for extended periods without discomfort.

Overall, the Craftsman 536.88644 combines power, versatility, and user-friendly features to create a reliable snow-clearing solution. With its robust performance, thoughtful design, and durable construction, this snow blower is well-suited for homeowners seeking to maintain clear pathways and driveways during the winter months. Whether faced with light snowfall or heavy blizzards, the Craftsman 536.88644 ensures efficient and effective snow removal.