Craftsman 536.88644 manual Product Specifications, AS Required, LUBRICATION-EVERY 25 Hours

Page 18

PRODUCT SPECIFICATIONS

HORSEPOWER

11.0 HP

 

DISPLACEMENT

21.82 cu. in.

GASOLINE

4 quarts

 

CAPACITY

(unleaded)

 

OIL CAPACITY

5W30

 

(20 oz capacity)

 

 

SPARK PLUG:

Champion

RJ19LM

 

(Gap .030

in.) or

 

equivalent

 

VALVE CLEARANCE:

Intake: .010 In.

 

Exhaust:

.010 in.

SNOW THROWER

AS REQUIRED

The following adjustment should be preformed more than once each sea- son.

1.Auger drive belt should be adjusted after the first 2 to 4 hours of use, again about mid-season and twice each season thereafter (See to Ad- just Belts paragraph in the Ser- vice and Adjustment section).

LUBRICATION-EVERY 25 HOURS

Lubricate Disc Drive Plate every twenty-five (25) hours and at the end of the season and/or before storage.

To Lubricate

1.Position speed selector lever in first gear.

2.Stand the snow thrower up on the auger housing end.

3.Remove the bottom panel.

4.Turn disc drive plate clockwise by hand until grease zerk is cleady visible at front center, See

Figure 16.

5.Place a coin or (a shim of equal thickness) between the rubber fric- tion wheel and disc drive plate to

prevent rubber friction wheel con- tacting the drive disc plate.

6.To grease zerk, use a hand grease gun, lubricate with a Hi Temp EP

Moly grease. Fill zerk only until grease becomes visible below bear-

ing assembly located under grease zerk. DO NOT over fill.

CAUTION: DO NOT allow grease to come in contract with the disc drive

plate or friction wheel or damage will result.

IMPORTANT: Remove coin and en- sure that a gap exists between friction

wheel and disc drive plate.

NOTE: Clean all excess grease found on friction disc hub.

Sprockets Hex Shaft and Sprockets

(Require No

Lubrication

Friction

Disc

Drive

Plate

\

Friction Bearing

E_WheelAssembly Point at which

Coin or Shim grease should

be visible

Gap Between

Friction Wheel

and Disc Drive Plate

Grease Zerk

Figure 16

LUBRICATION-NOT REQUIRED

1.Hex Shaft and Sprockets- Hex shaft and sprockets require no lu- brication. All bearings and bushings are lifetime lubricated and require no maintenance. See Figure 16.

NOTE: Any greasing or oiling of the above components can cause contami- nation of the friction wheel. If the disc

F-001087J18

Image 18
Contents Icrrftsmrni 001087JEspanol Wash Hands After HandlingTraining PreparationMaintenance and Storage Do not attempt to use snow thrower on a roofSafetyWarningSymbols SplitLockwasher 11/324-20 To Remove Snow Thrower From Carton Tools Required for AssemblyThrower Remove from the carton Place until needed for storageTo Assemble the Handle and Crank Assembly Caught between the upper and lower handleLoosen, but do not Universal To Install Shifter KnobPin. Spread ends of cotter pin to DriveHOW to SET the Skid Height Snow Chute AssemblyChecklist Service And Adjustment sectionKnow Your Snow Thrower Choke Control Used to start a coldTo USE Wheel Lockout PIN HOW to Move Forward and BackwardTo Stop Your Snow Thrower To Control Snow DischargeBefore Starting the Engine Fill GASDicates that alcohol blended Electric starter, if equipped To Stop EngineTo Start Engine Cold StartEngine runs smoothly, move choke lever to No Choke Position Do not prime if temperature above 50 F 10 CWarm Start Frozen StarterSnow Throwing Tips 001087J16General Recommendations Lubrication ChartCustomer Responsibilities After Each USELUBRICATION-EVERY 25 Hours Product SpecificationsAS Required Wheel and disc drive plateSpark Plug LubricationTo Change Engine OIL 001087J19To Adjust Skid Height To Adjust Scraper BARHOW to Check and Adjust Cables To Adjust BeltsDrive Lever Traction Drive Belt How To Remove The Auger Drive BeltTo Replace Belts Side/ %Belt Outdoors, away from fire orTraction Drive Belt AugerHow To Check The Friction Wheel HOW to Adjust or Replace the Friction WheelHOW to Adjust the Belt Guide Remove Top Bolt each sideHow To Replace The Friction Wheel To Adjust or Replace the Spark Plug HOW to Replace the Auger Shear BoltTo Adjust the Carburetor To adjustTo Replace Other Thoroughly clean the snow throwerEngine Provide maximum performance for the next seasonDifficult starting CauseTrouble CorrectionWasher Frame AssemblyScrew 001087J30Electric Start Assembly Motor StarterIdler Assembly Frame AssyCOVER, Bottom SEAL, OIL Gear Case AssemblyCase Gear Bearing217 Drive Components190 191 255247 245246 249Auger Housing Assembly 5OO48O PULLEY, 4L 6.12X 9517 711862 9357 301380-853 340720 710026 760875Discharge Chute Assembly CraftsmanWasher Plastic Handle Assembly OO1087J4073O 756Wheel Assembly 671 655 650 678Shift Yoke Assembly 791 792 8812Chute Control ROD Assembly 867866 Model Plate Decal Drive Clutch SymbolDecal Auger Clutch Symbol Decal Chute HandCraftsman 4-CYCLE Engine Model Number KEY Part NO. no KEY Part Description RPM650139 27677ALill Ill KEY PartIOA Spring Retainer 33290E Electric Starter VoltRetainer Ring Anti-drift SpringOO1087J52 KEY Part Description Part Idhhhh

536.88644 specifications

The Craftsman 536.88644 is a versatile snow blower designed to tackle the challenges of winter weather with efficiency and ease. As part of the Craftsman lineup, this machine exemplifies the brand's commitment to quality, performance, and user satisfaction.

One of the standout features of the Craftsman 536.88644 is its powerful engine. Equipped with a reliable 24-inch clearing width, the snow blower can efficiently handle heavy snowfall, making it an ideal choice for homeowners in areas that experience significant winter weather. The engine delivers robust performance, allowing the machine to handle not only light dustings but also deeper snow accumulations.

The Craftsman 536.88644 features a self-propelling system, which ensures that users can effortlessly maneuver the machine across various terrains. The adjustable speed settings offer flexibility, enabling users to customize their pace based on the snow conditions and their own preferences. This feature is particularly beneficial during heavy snowfall, where control and direction become crucial.

An additional innovative technology integrated into the design is the 180-degree chute rotation. This allows users to easily direct snow away from walkways, driveways, and parked vehicles, providing optimal snow management. The chute can be adjusted with a simple crank, making it user-friendly and efficient for rapid snow clearing tasks.

Durability is a key characteristic of the Craftsman 536.88644. Built with robust materials, it is engineered to withstand the rigors of winter use. The reinforced auger and impeller design not only enhances durability but also increases the machine's snow-throwing capability, allowing it to throw snow up to 40 feet away.

User comfort is also a consideration in the design of this snow blower. The ergonomically designed controls and comfortable grip handles reduce fatigue during operation, while the heated hand grips provide warmth during cold winter days. This thoughtful design ensures that users can operate the Craftsman 536.88644 for extended periods without discomfort.

Overall, the Craftsman 536.88644 combines power, versatility, and user-friendly features to create a reliable snow-clearing solution. With its robust performance, thoughtful design, and durable construction, this snow blower is well-suited for homeowners seeking to maintain clear pathways and driveways during the winter months. Whether faced with light snowfall or heavy blizzards, the Craftsman 536.88644 ensures efficient and effective snow removal.