Craftsman 536.88644 manual To Assemble the Handle and Crank Assembly, Loosen, but do not

Page 8

2.Removeand discardthe packing materialfrom around the snow thrower.

3.Cut down all four corners of the car- ton and lay the panels flat.

4.Roll snow thrower off the carton by pulling on the lower handle. CAU- TION: DO NOT back over cables.

. Remove the packing material from handle assembly.

6.Cut ties securing the clutch control cables to the lower handle and lay cable back away from the motor frame.

TO ASSEMBLE THE HANDLE AND CRANK ASSEMBLY

1.Cut tie holding shift rod to lower har_dle and move shifter to the first forward gear.

2.Loosen, but do not remove, the screws, flatwashers, Iockwashers, and hex nuts in the upper holes of the lower handle. See Figure 3.

Right Hand Side

Of Upper Handle_

Loosen, but do not

remove

11/32" Flatwasher

5/16" Hex

5/16" Screw

5/16" Split

Lockwasher

Figure 3

NOTE: Make sure the cables are not

caught between the upper and lower handle.

3.Raise the upper handle into operat-

ing position. Upper handle should be to the outside of the lower han-

dle.

NOTE: If the cables have become dis- connected form the clutch levers, rein- stall the cables as shown in Figure 4.

NOTE: Position cable through slots on shifter plate.

Clutch Lever

"Z" Fitting

Control

Cable _,,

Figure 4

4.Install hardware supplied in the parts bag (screw, flatwasher, lock- washer, and hex nut) into bottom hole on right hand side of handles. DO NOT tighten until all bolts are in place.

5.Locate crank assembly removed earlier and remove the nylon lock- nut and flatwasher from the eye bolt assembly. See Figure 5.

Left Hand Side Of,

Upper Handle

Crank

f

 

\

 

3/8" Nylon

 

 

 

y

Locknut

Eye Bolt

 

3/8"

 

Flatwasher

3/8"

Flatwasher

 

 

Figure 5

. Reinstall flatwasher and adaptor.

Install eye bolt through lower hole on the left hand side of the handle.

F--001087J8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Icrrftsmrni 001087JEspanol Wash Hands After HandlingTraining PreparationMaintenance and Storage Do not attempt to use snow thrower on a roofSafetyWarningSymbols 4-20 SplitLockwasher11/32 Tools Required for Assembly ThrowerTo Remove Snow Thrower From Carton Remove from the carton Place until needed for storageLoosen, but do not To Assemble the Handle and Crank AssemblyCaught between the upper and lower handle To Install Shifter Knob Pin. Spread ends of cotter pin toUniversal DriveSnow Chute Assembly ChecklistHOW to SET the Skid Height Service And Adjustment sectionKnow Your Snow Thrower Choke Control Used to start a coldHOW to Move Forward and Backward To Stop Your Snow ThrowerTo USE Wheel Lockout PIN To Control Snow DischargeDicates that alcohol blended Before Starting the EngineFill GAS To Stop Engine To Start EngineElectric starter, if equipped Cold StartDo not prime if temperature above 50 F 10 C Warm StartEngine runs smoothly, move choke lever to No Choke Position Frozen StarterSnow Throwing Tips 001087J16Lubrication Chart Customer ResponsibilitiesGeneral Recommendations After Each USEProduct Specifications AS RequiredLUBRICATION-EVERY 25 Hours Wheel and disc drive plateLubrication To Change Engine OILSpark Plug 001087J19To Adjust Skid Height To Adjust Scraper BARDrive Lever HOW to Check and Adjust CablesTo Adjust Belts How To Remove The Auger Drive Belt To Replace BeltsTraction Drive Belt Side/ %Outdoors, away from fire or Traction Drive BeltBelt AugerHOW to Adjust or Replace the Friction Wheel HOW to Adjust the Belt GuideHow To Check The Friction Wheel Remove Top Bolt each sideHow To Replace The Friction Wheel HOW to Replace the Auger Shear Bolt To Adjust the CarburetorTo Adjust or Replace the Spark Plug To adjustTo Replace Thoroughly clean the snow thrower EngineOther Provide maximum performance for the next seasonCause TroubleDifficult starting CorrectionFrame Assembly ScrewWasher 001087J30Electric Start Assembly Motor StarterCOVER, Bottom Idler AssemblyFrame Assy Gear Case Assembly Case GearSEAL, OIL BearingDrive Components 190 191217 255245 246247 249Auger Housing Assembly 5OO48O PULLEY, 4L 6.12X 9517 711862 9357 301380-853 340720 710026 760875Discharge Chute Assembly CraftsmanWasher Plastic Handle Assembly OO1087J4073O 756Wheel Assembly 671 655 650 678Shift Yoke Assembly 791 792 8812866 Chute Control ROD Assembly867 Decal Drive Clutch Symbol Decal Auger Clutch SymbolModel Plate Decal Chute HandCraftsman 4-CYCLE Engine Model Number KEY Part NO. no KEY Part Description RPM650139 27677ALill Ill KEY PartIOA 33290E Electric Starter Volt Retainer RingSpring Retainer Anti-drift SpringOO1087J52 KEY Part Description Part Idhhhh

536.88644 specifications

The Craftsman 536.88644 is a versatile snow blower designed to tackle the challenges of winter weather with efficiency and ease. As part of the Craftsman lineup, this machine exemplifies the brand's commitment to quality, performance, and user satisfaction.

One of the standout features of the Craftsman 536.88644 is its powerful engine. Equipped with a reliable 24-inch clearing width, the snow blower can efficiently handle heavy snowfall, making it an ideal choice for homeowners in areas that experience significant winter weather. The engine delivers robust performance, allowing the machine to handle not only light dustings but also deeper snow accumulations.

The Craftsman 536.88644 features a self-propelling system, which ensures that users can effortlessly maneuver the machine across various terrains. The adjustable speed settings offer flexibility, enabling users to customize their pace based on the snow conditions and their own preferences. This feature is particularly beneficial during heavy snowfall, where control and direction become crucial.

An additional innovative technology integrated into the design is the 180-degree chute rotation. This allows users to easily direct snow away from walkways, driveways, and parked vehicles, providing optimal snow management. The chute can be adjusted with a simple crank, making it user-friendly and efficient for rapid snow clearing tasks.

Durability is a key characteristic of the Craftsman 536.88644. Built with robust materials, it is engineered to withstand the rigors of winter use. The reinforced auger and impeller design not only enhances durability but also increases the machine's snow-throwing capability, allowing it to throw snow up to 40 feet away.

User comfort is also a consideration in the design of this snow blower. The ergonomically designed controls and comfortable grip handles reduce fatigue during operation, while the heated hand grips provide warmth during cold winter days. This thoughtful design ensures that users can operate the Craftsman 536.88644 for extended periods without discomfort.

Overall, the Craftsman 536.88644 combines power, versatility, and user-friendly features to create a reliable snow-clearing solution. With its robust performance, thoughtful design, and durable construction, this snow blower is well-suited for homeowners seeking to maintain clear pathways and driveways during the winter months. Whether faced with light snowfall or heavy blizzards, the Craftsman 536.88644 ensures efficient and effective snow removal.
Top Page Image Contents