Tascam CD-RW5000 owner manual Messages, troubleshooting, etc, Troubleshooting

Page 21

5 - Messages, troubleshooting, etc.

The following messages may appear on the display under certain circumstances. The meaning of these messages, and any countermeasures which are appro- priate are given here.

Message

Meaning and countermeasure (if

appropriate)

 

 

 

 

 

 

The disc has been inserted, and the disc

READING

information is being read by the

 

CD-RW5000.

 

 

 

Optimal Power Calibration is in progress

 

(a recordable disc has been inserted, and

OPC

the CD-RW5000 is adjusting its internal

 

mechanism to match the disc

 

characteristics.)

 

 

 

No disc is loaded into the CD-RW5000.

NO DISC

You may also see this message if you

load a disc upside-down or load a dirty

 

 

disc.

 

 

 

After recording has finished, the

 

CD-RW5000 updates a temporary table of

UPDATE

contents, and displays this message. This

is not the same as the permanent table of

 

 

contents produced by a finalizing

 

operation.

 

 

WAIT

The CD-RW5000 is busy with an internal

operation.

 

 

 

 

More than 20 tracks have been

FULL

programmed for programmed playback

 

(see 3.3.1, "Programmed playback").

 

 

CD FULL

No more space is left for recording on the

disc.

 

 

 

 

You have tried to finalize an empty disc; it

EMPTY

is not possible to write a table of contents

 

for an empty disc!

 

 

 

Sync start has been selected to

 

synchronize recording with a digital audio

INPUT

source (4.2, "Recording from digital

 

sources") but a digital source has not

 

been selected as the input.

 

 

 

The OPC operation has been carried out

FINAL

more than 96 times; this is a warning to

 

you that the disc must now be finalized.

 

 

 

The data on the disc was corrupted,

 

possibly due to a power failure during a

RECOVER

write operation. The CD-RW5000 is

 

attempting to restore the corrupted data

 

so that the disc can be used.

 

 

Message

Meaning and countermeasure (if

appropriate)

 

 

 

 

 

 

The OPC operation has failed when the

 

disc is inserted. This may be due to the

 

disc having been inserted more than 99

OPC FAIL

times, or it may be that the disc is dirty. If

you know that the disc has not been

 

 

inserted more than 99 times, clean the

 

disc using the methods described in 1.1,

 

"About CD-R and CD-RW discs".

 

 

 

The CD-RW5000 has failed its self-check

 

operation. Remove any disc, turn off the

SERVICE

CD-RW5000, wait a few seconds and turn

it back on again. If this message appears

 

 

again, contact your TASCAM service

 

center.

 

 

 

 

5.1 Troubleshooting

In addition to the messages above, here is a list of problems and possible solutions:

Problem

Solution

 

 

 

 

 

Make sure the power cable is connected

 

to a power socket of the correct voltage.

No power

Reset the CD-RW5000 by switching the

 

power switch off, waiting for a short while,

 

and switching it on again.

 

 

 

Are the correct connections made to the

No sound on

amplifying equipment?

Is the input selector of the amplifying

replay

equipment switched to the correct

 

 

source?

 

 

 

Are the balanced XLR-type connectors

Distorted sound

connected to a +4 dBu input?

Are the trimmers on the balanced

 

 

XLR-type outputs turned up?

 

 

Sound is too

Are the unbalanced RCA connectors

faint

connected to a –10 dBV input?

 

 

 

Is the disc label side upwards and placed

Disc does not

correctly in the disc tray?

Is the disc clean?

start

Try another disc to see if the problem lies

 

 

with a particular disc

 

 

Cannot select

Sync start is selected for a digital input

manual track

source (4.3, "Automatic track division")

division

 

 

 

 

The input levels are set too high (analog

Recording is

recording)

The –10 dBV inputs of the CD-RW5000

distorted

are receiving analog signals from a

 

 

+4 dBu signal source.

 

 

TASCAM CD-RW5000 21

Image 21
Contents CD-RW5000 Important for U.K. Customers Important Safety PrecautionsImportant Safety Instructions Safety Information Table of Contents About CD-R and CD-RW discs IntroductionFinalizing Unpacking the CD-RW5000Environmental considerations Use of CD-R and CD-RW discs Parts of the CD-RW5000 Front panel Rear panel RC-RW5000 remote control unit Repeat key Number keysPGM key Track Incr keyDisplay modes Playback operationsPlaying back a selected track Repeating playbackFast searching General recording notes Recording operationsRecording from digital sources Disc typesOptical Recording with synchronized startManual track division Automatic track divisionAnalog recording Finalizing discsReference levels Erasing material CD-RW only Erasing a finalized discErasing a track on a non-finalized disc Troubleshooting Messages, troubleshooting, etcSelf-diagnostic program Specifications Audio specificationsI/O specifications Physical specifications Dimensional drawingCD-RW Index a RIndex S U CD-RW5000

CD-RW5000 specifications

The Tascam CD-RW5000 is a professional-grade CD recorder and player, renowned for its robustness and versatility in music and audio production environments. Positioned as a reliable solution for both live performances and studio applications, the CD-RW5000 features a sleek design and an array of advanced technologies that cater to a variety of audio recording needs.

One of the primary features of the CD-RW5000 is its ability to record, play, and finalize CDs in both CD-R and CD-RW formats. This flexibility allows users to create audio CDs for distribution or for archival purposes. The device is equipped with high-quality A/D and D/A converters that ensure exceptional sound fidelity, capturing every nuance of the input signal and delivering a clear and detailed output.

The CD-RW5000 also boasts a range of connectivity options, including balanced analog XLR inputs and outputs, unbalanced RCA connectors, and digital inputs and outputs via both optical and coaxial connections. This makes it easy to integrate the unit into various audio setups, allowing users to connect microphones, mixers, and other audio equipment directly to the recorder.

Another standout feature is the built-in editing capabilities. The CD-RW5000 allows users to perform track segmentation, which means they can easily divide long recordings into individual tracks. Additionally, users can add Index points for easier navigation, making it a valuable tool for creating live recordings, interviews, and multi-track sessions.

The device’s ease of use is augmented by its straightforward user interface and bright LCD display, which provides clear information on track status and recording settings. The front panel includes dedicated buttons for functions like repeat, program, and shuffle, allowing for seamless operation during playback and recording sessions.

Tascam also incorporates a range of advanced features to enhance the user experience, such as pitch control and a fader start function, allowing for synchronized playback with compatible equipment. The inclusion of a remote control also adds an extra layer of convenience, making it easier to operate the device from a distance.

In summary, the Tascam CD-RW5000 stands out as a versatile and reliable CD recorder with a wealth of features designed to meet the demands of professionals in the audio industry. Its robust construction, exceptional sound quality, and ease of use make it a preferred choice for those looking to capture high-quality audio in various settings, whether on stage or in the studio.