Craftsman 247.8879 manual Oil, Gasoline, Electric Starter, Recoil Starter

Page 11

OPERATION

Before Starting Engine

WARNING: Read, understand, and follow all instructions and warnings on the machine and in this manual before operating.

Oil

The engine was shipped with oil in the engine. Check oil level before each operation to ensure adequate oil in the engine. For further instructions, refer to the steps on page 15.

1. Remove the dipstick from the oil fill.

2Check and make sure that the level of oil is up to the FULL mark on the dipstick.

3.If the oil level is not up to FULL, pour fresh motor oil (5W-30, with a minimum classification of SL/SJ) slowly through the opening. Replace oil fill dipstick and check oil level again.

Gasoline

WARNING: Use extreme care when handling gasoline. Gasoline is extremely flammable and the vapors are explosive. Never fuel the machine indoors or while the engine is hot or running. Extinguish cigarettes, cigars, pipes and other sources of ignition.

•Store gasoline in a clean, approved container and keep the cap in place on the container.

•Make sure that the container from which you pour the gasoline is clean and free from rust or other foreign particles.

NOTE: A plastic dust cap may be found inside the fuel fill opening. Remove and discard, if present.

•Always fill the fuel tank outdoors and use a funnel or spout to prevent spilling.

•Fill fuel tank with clean, fresh, unleaded gasoline.

•Never fill the fuel tank completely. Fill the tank to within 1/2” from the top to provide space for expansion of fuel.

•Make sure to wipe off any spilled fuel before starting the engine.

Starting The Engine

Electric Starter

1.Determine that your home’s wiring is a three-wire grounded system. Ask a licensed electrician if you are not certain.

WARNING: The optional electric starter is equipped with a grounded three-wire power cord and plug, and is designed to operate on 120 volt AC household current. It must be used with a properly grounded three- prong receptacle at all times to avoid the possibility of electric shock.

If your home’s wiring system is not a three- wire grounded system, do not use this electric starter under any conditions.

If your home electrical system is grounded, but a three-hole receptacle is not available, do not use your snow thrower’s electric starter.

Follow all instructions carefully prior to operating the electric starter.

If you have a grounded three-prong receptacle, proceed as follows:

1.Plug the extension cord into the outlet located on the engine’s surface. Plug the other end of extension cord into a three-prong 120-volt, grounded, AC outlet in a well-ventilated area.

2.Rotate choke control to FULL choke position (for a cold engine start).

NOTE: If the engine is already warm, place choke control in the OFF position instead of FULL.

3.Push the primer two or three times for cold engine start, making sure to cover vent hole in the center of the primer when pushing.

NOTE: DO NOT use primer to restart a warm engine after a short shutdown.

4.Push starter button to start engine.

5.Once the engine starts, release starter button.

1.Attach spark plug wire to spark plug. Make certain the metal loop on the end of the spark plug wire (inside the rubber boot) is fastened securely over the metal tip on the spark plug.

2.Make certain both the auger control and drive control are in the disengaged (released) position.

3.Move throttle control up to FAST position. Insert ignition key into slot. Make sure it snaps into place. Do not attempt to turn the key.

NOTE: The engine cannot start without the key is fully inserted into the ignition switch.

6.As the engine warms, slowly rotate the choke control to the OFF position. If the engine falters, quickly rotate the choke control back to FULL and then slowly into the OFF position again.

7.When disconnecting the extension cord, always unplug the end at the three-prong wall outlet before unplugging the opposite end from the snow thrower.

Recoil Starter

1. Rotate choke control to FULL choke position (cold engine start).

NOTE: If the engine is already warm, place choke control in the OFF position instead of FULL.

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Operator’s Manual Model Number Table of ContentsWarranty Statement Product SpecificationsChine Safety LabelsYour Responsibility Training Safe Operation PracticesDo not modify engine OperationRemoving From Carton AssemblyAssembly Tire Pressure Shear Pin StorageAuger Control Skid ShoesOperation $26% #/.42 Recoil Starter OilGasoline Electric StarterAuger Control Test Stopping The EngineMaintenance Check Augers Changing OilCheck Chute Cables Check Spark PlugAuger Belt Service & AdjustmentsReplacing Belts Friction Wheel Rubber Drive BeltChute Control Any adjustments while engine is runningShift Cable Retighten nuts and bolts securely Drive ControlLong-Term Storage OFF-SEASON StorageShort-Term Storage Troubleshooting Parts List Description Craftsman 9 H.P. Snow Thrower ModelParts List 684-04112B 55 56 Auger Clutch Cable Guide Bracket Page Piston, Pin & Ring Set .010 OS incl SAE 5W30, 4-Cycle Engine Oil Quart 640349 590574 Mitten Grip Handle optional 35450 Ring 35915 Armature 35451B Housing Assembly 35452A This page applicable in the U.S.A. and Canada only Sears Emission Control Defects Warranty CoverageOwner’s Warranty Responsibilities Sears Emission Control Defects Warranty ProvisionsPage Repair Protection Agreement Manual del operador Producto ÍndiceDeclaración DE Garantía Especificaciones DELMáquina quitanieve Etiquetas DE SeguridadLimpiar el montaje del cana Capacitación Prácticas DE Operación SegurasCalcomanía de identificación del motor OperaciónNo modifique el motor Aviso referido a emisionesManija inferior MontajeExcepción será especificado InferiorAlmacenamiento del pasador de cuchilla Herramienta de limpiezaCada invierno. Si no respeta estas instruc Ajustes finalesPrueba de control de la barrena De la barrena antes de operar su máquinaPresión de los neumáticos Control de transmisión y palanca de cambiosZapata antideslizante Operación Para encender el motor Antes de encender el motorArrancador de retroceso congelado Arrancador de retrocesoArranque en frío Arranque en calienteProcedimiento para engranar las barrenas Antes de detener la máquinaProcedimiento para quitar la nieve Procedimiento para engranar la transmisiónMantenimiento Control de las barreras Cambio de aceiteRevise los cables del canal Controle la bujíaCorrea de la barrena Servicio Y AjustesReemplazo de las correas Cercano según las instrucciones de la página Correa de transmisiónGoma de la rueda de fricción Miento Cable de cambiosControl del canal Para ajustar el control de la barrena, consulte la página Control de la transmisiónZapatas antideslizantes Ajuste, proceda de la siguiente maneraAlmacenarla Problemas de encendidoAlmacenamiento Fuera DE Temporada Dispositivo a gasSolución DE Problemas Piezas con garantía Esta página se aplica sólo en EE.UU. y CanadáAcuerdo DE Protección Para Reparaciones Notas Get it fixed, at your home or ours

247.8879 specifications

The Craftsman 247.8879 is a versatile and reliable snow thrower designed to tackle winter’s harshest conditions. This powerful machine has gained popularity among homeowners for its efficiency, ease of use, and robust build.

One of the main features of the Craftsman 247.8879 is its 24-inch clearing width. This allows users to clear large areas rapidly, making it ideal for driveways, sidewalks, and patios. The snow thrower is equipped with a 208cc engine, providing ample power to handle heavy, wet snow. This engine not only enhances performance but also ensures efficient fuel consumption, offering an excellent balance between power and economy.

Another standout characteristic of the Craftsman 247.8879 is the six-speed transmission, which includes four forward speeds and two reverse speeds. This feature enables users to maintain control while navigating various terrains and snow depths, making it adaptable to different conditions. The adjustable, polymer skid shoes further enhance the snow thrower’s performance, allowing for easy height adjustments to prevent damage to surfaces while ensuring a thorough clean.

The snow thrower also features a 180-degree rotating chute, which allows users to direct the snow where it needs to go quickly. Operators can easily adjust the chute direction with a simple lever, making it convenient to maneuver around obstacles and control where the snow is thrown. Additionally, the ergonomic handles provide comfort during operation, reducing fatigue during extended use.

Safety is a crucial aspect of the Craftsman 247.8879, which comes equipped with an electric start feature. This means that users can start the machine with the push of a button, eliminating the hassle of pulling a cord in cold weather. Furthermore, the snow thrower's design emphasizes stability and control, enhancing safety while in operation.

In terms of durability, the Craftsman 247.8879 boasts heavy-duty construction that can withstand the rigors of winter use. Materials used in the build are designed to resist wear and tear, ensuring longevity. With all these features combined, the Craftsman 247.8879 stands out as a reliable partner for tackling snowy conditions, making it a smart investment for homeowners looking to simplify their winter maintenance tasks.
Top Page Image Contents