Craftsman 247.8879 manual OFF-SEASON Storage, Short-Term Storage, Long-Term Storage

Page 19

OFF-SEASON STORAGE

If the snow thrower will not be used for 30 days or longer, or if it is the end of the snow season when the last possibility of snow is gone, the equipment needs to be stored properly. Follow storage instructions below to ensure top performance from the snow thrower for many more years.

Preparing Engine

Short-Term Storage

It is important to prevent gum deposits from forming in essential fuel system parts of the engine such as the carburetor, fuel filter, fuel hose, or tank during short-term storage (15-30 days). To prevent this, treat the fuel system using a fuel stabalizer.

Fuel stabilizer (such as STA-BIL™ or ULTRA-FRESH™) is an accept- able alternative in minimizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage container. Always follow mix ratio found on stabilizer container. Run engine at least 10 minutes after adding stabilizer to allow it to reach the carbure- tor.

WARNING: Never store snow thrower with fuel in tank indoors or in poorly ventilated areas, where fuel fumes may reach an open flame, spark or pilot light as on a furnace, water heater, clothes dryer or gas appliance.

CAUTION: Alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage.

Long-Term Storage

To avoid engine problems, the fuel system should be emptied before storage for 30 days or longer.

WARNING: Fuel left in engine during warm weather deteriorates and will cause serious starting prob- lems.

1.Run the engine until the fuel tank is empty and it stops due to lack of fuel. Do not attempt to pour fuel from the engine.

WARNING: Never use engine or carburetor cleaning products in the fuel tank or permanent damage may occur.

2.Remove the spark plug and pour one (1) ounce of engine oil through the spark plug hole into the cylinder. Cover spark plug hole with a rag and crank the engine several times to distribute the oil. Replace spark plug.

Preparing Snow Thrower

•When storing the snow thrower in an unventilated or metal storage shed, care should be taken to rustproof the equipment. Using a light oil or silicone, coat the equipment, especially any chains, springs, bearings and cables.

•Remove all dirt from exterior of engine and equipment.

•Follow lubrication recommendations.

•Store equipment in a clean, dry area.

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Operator’s Manual Model Number Table of ContentsWarranty Statement Product SpecificationsYour Responsibility Safety LabelsChine Training Safe Operation PracticesDo not modify engine OperationRemoving From Carton AssemblyAssembly Tire Pressure Shear Pin StorageAuger Control Skid ShoesOperation $26% #/.42 Recoil Starter OilGasoline Electric StarterAuger Control Test Stopping The EngineMaintenance Check Augers Changing OilCheck Chute Cables Check Spark PlugReplacing Belts Service & AdjustmentsAuger Belt Friction Wheel Rubber Drive BeltShift Cable Any adjustments while engine is runningChute Control Retighten nuts and bolts securely Drive ControlShort-Term Storage OFF-SEASON StorageLong-Term Storage Troubleshooting Parts List Description Craftsman 9 H.P. Snow Thrower ModelParts List 684-04112B 55 56 Auger Clutch Cable Guide Bracket Page Piston, Pin & Ring Set .010 OS incl SAE 5W30, 4-Cycle Engine Oil Quart 640349 590574 Mitten Grip Handle optional 35450 Ring 35915 Armature 35451B Housing Assembly 35452A This page applicable in the U.S.A. and Canada only Sears Emission Control Defects Warranty CoverageOwner’s Warranty Responsibilities Sears Emission Control Defects Warranty ProvisionsPage Repair Protection Agreement Manual del operador Producto ÍndiceDeclaración DE Garantía Especificaciones DELLimpiar el montaje del cana Etiquetas DE SeguridadMáquina quitanieve Capacitación Prácticas DE Operación SegurasCalcomanía de identificación del motor OperaciónNo modifique el motor Aviso referido a emisionesManija inferior MontajeExcepción será especificado InferiorAlmacenamiento del pasador de cuchilla Herramienta de limpiezaCada invierno. Si no respeta estas instruc Ajustes finalesPrueba de control de la barrena De la barrena antes de operar su máquinaZapata antideslizante Control de transmisión y palanca de cambiosPresión de los neumáticos Operación Para encender el motor Antes de encender el motorArrancador de retroceso congelado Arrancador de retrocesoArranque en frío Arranque en calienteProcedimiento para engranar las barrenas Antes de detener la máquinaProcedimiento para quitar la nieve Procedimiento para engranar la transmisiónMantenimiento Control de las barreras Cambio de aceiteRevise los cables del canal Controle la bujíaReemplazo de las correas Servicio Y AjustesCorrea de la barrena Goma de la rueda de fricción Correa de transmisiónCercano según las instrucciones de la página Control del canal Cable de cambiosMiento Para ajustar el control de la barrena, consulte la página Control de la transmisiónZapatas antideslizantes Ajuste, proceda de la siguiente maneraAlmacenarla Problemas de encendidoAlmacenamiento Fuera DE Temporada Dispositivo a gasSolución DE Problemas Piezas con garantía Esta página se aplica sólo en EE.UU. y CanadáAcuerdo DE Protección Para Reparaciones Notas Get it fixed, at your home or ours

247.8879 specifications

The Craftsman 247.8879 is a versatile and reliable snow thrower designed to tackle winter’s harshest conditions. This powerful machine has gained popularity among homeowners for its efficiency, ease of use, and robust build.

One of the main features of the Craftsman 247.8879 is its 24-inch clearing width. This allows users to clear large areas rapidly, making it ideal for driveways, sidewalks, and patios. The snow thrower is equipped with a 208cc engine, providing ample power to handle heavy, wet snow. This engine not only enhances performance but also ensures efficient fuel consumption, offering an excellent balance between power and economy.

Another standout characteristic of the Craftsman 247.8879 is the six-speed transmission, which includes four forward speeds and two reverse speeds. This feature enables users to maintain control while navigating various terrains and snow depths, making it adaptable to different conditions. The adjustable, polymer skid shoes further enhance the snow thrower’s performance, allowing for easy height adjustments to prevent damage to surfaces while ensuring a thorough clean.

The snow thrower also features a 180-degree rotating chute, which allows users to direct the snow where it needs to go quickly. Operators can easily adjust the chute direction with a simple lever, making it convenient to maneuver around obstacles and control where the snow is thrown. Additionally, the ergonomic handles provide comfort during operation, reducing fatigue during extended use.

Safety is a crucial aspect of the Craftsman 247.8879, which comes equipped with an electric start feature. This means that users can start the machine with the push of a button, eliminating the hassle of pulling a cord in cold weather. Furthermore, the snow thrower's design emphasizes stability and control, enhancing safety while in operation.

In terms of durability, the Craftsman 247.8879 boasts heavy-duty construction that can withstand the rigors of winter use. Materials used in the build are designed to resist wear and tear, ensuring longevity. With all these features combined, the Craftsman 247.8879 stands out as a reliable partner for tackling snowy conditions, making it a smart investment for homeowners looking to simplify their winter maintenance tasks.
Top Page Image Contents