Meyer 62504, 62517, 62505, 62209 Installation and Assembly Instructions, Installation Instructions

Page 3

INSTALLATION AND ASSEMBLY INSTRUCTIONS

INSTALLATION INSTRUCTIONS:

The 1.8 and 2.0 Series Spreaders can mount and store as a single unit and will mount on most medium, heavy-duty/pick-up trucks as well as 1 ton trucks

WARNING

THE SPREADER UNIT MUST BE SECURELY FASTENED TO THE VEHICLE. FAILURE TO NOT PROPERLY RESTRAIN THE UNIT COULD PERMIT THE UNIT TO BREAK FREE FROM THE TRUCK AND CREATE A POTENTIAL FOR A LIFE THREATENING ACCIDENT.

DO NOT OVERLOAD THE VEHICLE. It is quite possible to overload the vehicle by improperly mounting or over loading the spreader. This could result in dangerous stability and braking problems. Always consult and follow the truck manufacturer’s instructions.

WARNING

BEFORE BEGINING ANY INSTALLATION ON THIS UNIT, disconnect the spreader battery negative cable if already installed.

1.Place the Spreader in the rear of truck with the engine/hydraulic motor to the rear of the truck. Center the spreader (side to side) in the truck. The spreader should extend past the rear of the outer most part of the truck (i.e: truck bed, bumper) approximately 18 inches.

CAUTION

INSURE THAT THE SPREADER CANNOT TIP WHEN THE SPINNER ASSEMBLY IS ATTACHED

SPINNER ASSEMBLY

a.Raise engine shroud and prop it open with the support rod. (If engine driven model)

b.Slide the spinner frame assembly into the rear of the longitudinal with the spinner back plate toward the rear.

c.Bolt the spinner to the longitudinals using the four (4) 3/8” x 1” bolts, 3/8” flange nuts and flatwashers from hardware bag located on the spinner. Using one (1) 3/8” x 1” bolt, flatwashers and flange nut from hardware bag, bolt the top portion of the spinner back plate to the engine plate.

d.Install roller chain between the gear box sprocket and the spinner sprocket.

Make sure sprockets are in line with each other. The roller chain is tightened first by loosening all four (4) 3/8” bolts on the back plate; then pull the entire bearing/shaft assembly in such a way to achieve the proper amount of chain tension. Make sure the spinner shaft is straight up and down before re-tightening.

2.Reposition the spreader in the truck, just short of making contact with the rearmost part of the truckbed, bumper, pintle hook etc. Bolt the unit to the truck using a minimum of four (4) 1/2” - grade 5 bolts and corresponding washers and locknuts.

The spreader is designed to sit flat on the bed of the truck, supported by the longitudinals/sides.

DO NOT SUPPORT THE SPREADER BY THE BODY JACKS ALONE!! UNIT IS NOT DESIGNED FOR CHASSIS MOUNT APPLICATIONS!

3

Image 3
Contents Index 2.0 CU. YD. Insert Hopper SpreaderTurn OFF ALL Power Before Performing ANY Service Operations Safe Equipment Installers and OperatorsInstallation Instructions Installation and Assembly InstructionsInstallation Instructions Optional HOLD-DOWN KITPart Number QTY Description Electric Throttle Go to Assembly InstructionsDiagram a Table for Diagram a Factory Installed Actuators Installation Instruction for Electric Throttle ControlsSerious Injury or Death Might Occur Center High Mount Stop Lamp Chsml PV Spreader Chmsl InstallationCenter High Mounting Stop Light Hydraulics Control and Hydraulic System SpecificationsSingle Flow Control Valve Dual Flow VALVE/STAND Installation InstructionsThrottle Electric Throttle Control Panel Switch Functions Spreader Operation Desired Spread Pattern Baffle SettingService Bulletin no Maintenance Parts List Part Number QTY Description Parts List for Hydraulic MotorHydraulic Driven Hopper Spreader Parts List for Hydraulic Driven Hopper Assemblies Hydraulic Driven Hopper Spreader Carbon Steel Cu. Yd.62520 2.0 Cu. Yd Hydraulic Driven Hopper Spreader Stainless Steel After 11-1998 S/N Cu. Yd.62522 2.0 Cu. Yd Hydraulic Driven Hopper Spreader Stainless Steel Cu. Yd.62522 2.0 Cu. Yd Engine Driven Hopper Spreader Parts List for Engine Driven Hopper Assemblies Engine Driven Hopper Spreader Chain Roller No Old Style Hopper use Parts List for Engine Driven43, 44 Stainless Steel After 11-1998 S/N Cu. Yd.62516 2.0 Cu. Yd 43, 44 Stainless Steel Cu. Yd.62516 2.0 Cu. Yd 1822 QTY Description Parts List for Durst Gear BOX AssemblySuperior Gearbox Assembly After 11/4/02 Parts List for Superior Gearbox AssemblyShort Spinner Assembly PART. no QTY Description Parts List for Spinner Assembly Short Parts onlyParts List for Hydraulic Motor Driven Units Original Version of StandardIntermediate Standard Spinner Assembly Extended Hydraulic Steel Spinner Assy Extended Spinner Assembly Parts List for Extended Spinner Assembly Extended Parts only Electric Controls Parts & Schematic Honda Actuator PIN Connector Cable & PlugParts List Honda Actuator Electric Controls Parts & SchematicBriggs Actuator Briggs Actuator MTG. Tabs Control BOXParts List PART. no QTY Description Parts List for Control Panel AssemblyPage Auxilary Components Parts List for Shipping CartonName Plate Information Spreader ONE Year Warranty Meyer Products Euclid Avenue Cleveland, Ohio