Celestron OMNI XLT 102 manual Long Exposure Prime Focus Photography

Page 38

1.Find and center the desired target in the viewfinder of your camera.

2.Turn the focus knob until the image is as sharp as possible.

3.Place the black card over the front of the telescope.

4.Release the shutter using a cable release.

5.Wait for the vibration caused by releasing the shutter to diminish. Also, wait for a moment of good seeing.

6.Remove the black card from in front of the telescope for the duration of the exposure (see accompanying table).

7.Replace the black card over the front of the telescope.

8.Close the camera's shutter.

Advance the film and you are ready for your next exposure. Don't forget to take photos of varying duration and keep accurate records of what you have done. Record the date, telescope, exposure duration, eyepiece, f/ratio, film, and some comments on the seeing conditions.

The following table lists exposures for eyepiece projection with a 10mm eyepiece. All exposure times are listed in seconds or fractions of a second.

Planet

ISO 50

ISO 100

ISO 200

ISO 400

Moon

4

2

1

1/2

Mercury

16

8

4

2

Venus

1/2

1/4

1/8

1/15

Mars

16

8

4

2

Jupiter

8

4

2

1

Saturn

16

8

4

2

Table 6-2

Recommended exposure time for photographing planets.

The exposure times listed here should be used as a starting point. Always make exposures that are longer and shorter than the recommended time. Also, take a few photos at each shutter speed. This will ensure that you get a good photo. It is not uncommon to go through an entire roll of 36 exposures and have only one good shot.

NOTE: Don't expect to record more detail than you can see visually in the eyepiece at the time you are photographing.

Once you have mastered the technique, experiment with different films, different focal length eyepieces, and even different filters.

Long Exposure Prime Focus Photography

This is the last form of celestial photography to be attempted after others have been mastered. It is intended primarily for deep-sky objects, objects outside our solar system which includes star clusters, nebulae, and galaxies. While it may seem that high magnification is required for these objects, just the opposite is true. Most of these objects cover large angular areas and fit nicely into the prime focus field of your telescope. The brightness of these objects, however, requires long exposure times and, as a result, is rather difficult.

There are several techniques for this type of photography, and the one chosen will determine the standard accessories needed. The best method for long exposure deep sky astrophotography is with an off-axis guider when you are using a Schmidt-Cassegrain. This device allows you to photograph and guide through the telescope simultaneously. Celestron offers a very special and advanced off-axis guider, called the Radial Guider (# 94176). In addition, you will need a T-Ring to attach your camera to the Radial Guider. With refractor and Newtonian telescopes you can skip the comments about the Radial Guider but all else applies.

Other equipment needs include a guiding eyepiece. Unlike other forms of astrophotography which allows for fairly loose guiding, prime focus requires meticulous guiding for long periods. To accomplish this you need a guiding ocular with an illuminated reticle to monitor your guide star. For this purpose, Celestron offers the Micro Guide Eyepiece (# 94171). Here is a brief summary of the technique:

38

Page 37 Page 39
Image 38
Page 37 Page 39
Contents Omni XLT Series Telescopes Table of Contents Astrophotography Page Omni XLT 102 Refractor Omni XLT 150 Newtonian Omni XLT 127 Schmidt-Cassegrain Setting up the Tripod Attaching the Equatorial Mount Installing the Counterweight Bar Attaching the Center Leg BraceInstalling the Counterweights Attaching the Slow Motion Control Knobs CablesAttaching the Telescope Tube to the Mount Installing the Finderscope Installing the Visual BackInstalling the Star Diagonal Installing the EyepiecesMoving the Telescope Manually Balancing the Mount in R.AAdjusting the Mount Balancing the Mount in DECAdjusting the Mount in Altitude Adjusting the Mount in AzimuthPage Page Focusing Image OrientationAligning the Finderscope Calculating MagnificationDetermining Field of View General Observing HintsCelestial Coordinate System Motion of the Stars Latitude Scale Pointing at PolarisFinding the North Celestial Pole Polar Alignment in the Southern Hemisphere Polar Alignment with the Latitude ScalePointing at Sigma Octantis Finding the South Celestial Pole SCPDeclination Drift Method of Polar Alignment Aligning the R.A. Setting Circle Using the R.A. Vernier Scale 11 Vernier ScaleObserving the Planets Observing the MoonLunar Observing Hints Planetary Observing HintsObserving Deep Sky Objects Observing the SunSolar Observing Hints Seeing ConditionsUsing the Lens Cap Aperture Stop with Refractor Telescopes SeeingPiggyback Photography Using Digital Cameras Eyepiece Projection for a Schmidt-Cassegrain FullLong Exposure Prime Focus Photography Planetary and Lunar Photography with Special Imagers Metering CCD Imaging for Deep Sky ObjectsTerrestrial Photography Reducing VibrationCare and Cleaning of the Optics Collimation of RefractorsCollimation of a Schmidt-Cassegrain Two 2 turnsCollimated telescope Should appear Symmetrical with Collimation of a Newtonian Aligning the Secondary MirrorBoth mirrors aligned with your eye looking into the focuser Night Time Star Collimating As a Series 1 # Page Page Appendix a Technical Specifications Appendix B Glossary of Terms Page Page Page Page Page Page Page Page Celestron Two Year Warranty
Top Page Image Contents