ViewSonic PJ656 manual Maintenance, Lamp

Page 44

Maintenance

Maintenance

Lamp

WARNING

HIGH VOLTAGE

 

HIGH TEMPERATURE

HIGH PRESSURE

 

►The projector uses a high-pressure mercury glass lamp. The lamp can break with a loud bang, or burn out, if jolted or scratched, handled while hot, or worn over time. Note that each lamp has a different lifetime, and some may burst or burn out soon after you start using them. In addition, when the bulb bursts, it is possible for shards of glass to fly into the lamp housing, and for gas containing mercury to escape from the projector’s vent holes.

►About disposal of a lamp • This product contains a mercury lamp; do not put it in a trash. Dispose of it in accordance with environmental laws.

For lamp recycling, go to www.lamprecycle.org. (in the US)

For product disposal, contact your local government agency or www.eiae.org (in the US) or www.epsc.ca (in Canada).

For more information, call your dealer.

• If the lamp should break (it will make a loud bang when it does), unplug the power cord from the outlet, and make sure to request a replacement lamp from your local dealer. Note that shards of glass could damage the inside of the projector, or cause injury during handling, so please do not try to clean the projector or replace the lamp yourself.

Disconnect • If the lamp should break (it will make a loud bang when it does),

the plug

ventilate the room well, and make sure not to breathe the gas that

from the

comes out of the projector vents, or get it in your eyes or mouth.

power

• Before replacing the lamp, turn the projector off and unplug the power

outlet

cord, then wait at least 45 minutes for the lamp to cool sufficiently.

 

Handling the lamp while hot can cause burns, as well as damaging the

 

lamp.

•Never unscrew except the appointed (marked by an arrow) screws.

•Do not open the lamp cover while the projector is suspended from the ceiling. This is dangerous, since if the lamp’s bulb has broken, the shards will fall out when the cover is opened. In addition, working in high places is dangerous, so ask your local dealer to have the lamp replaced even if the bulb is not broken.

•Do not use the projector with the lamp cover removed. To replace the lamp, make sure that the screws are tightened firmly. Loose screws could result in damage or injury.

•Use only the lamp of the specified type.

•If the lamp breaks soon after the first time it is used, it is possible that there are electrical problems elsewhere besides the lamp. If this happens, contact your local dealer or a service representative.

•Handle with care: jolting or scratching could cause the lamp bulb to burst during use.

•Using the lamp for long periods of time could cause it not to light up or to burst. When the pictures appear dark or when the color tone is poor, please replace the lamp as soon as possible. Do not use old (used) lamps; this is a potential cause of breakage.

ViewSonic

PJ656

40

Page 43 Page 45
Image 44
Page 43 Page 45
Contents ViewSonic Compliance Information Important Safety Instructions Copyright Information Product Registration For Your RecordsContents of package About this manualContent About contents of package Fastening the lens cover Part names ProjectorComponent CB/PB CR/PRRemote control Control buttonsSetting up At 16 9 Screen ArrangementAt 4 3 Screen Adjusting the projectors elevator Using the Security Bar How to attachConnecting your devices About Plug-and-Play capabilityExamples of connection with a computer Connecting to a monitor outputConnecting to a speaker with amplifier output Examples of connection with a VCR/DVD player P B P RConnecting power supply Remote control Putting batteriesUsing the remote control Power on/off Turning on the powerTurning off the power STANDBY/ON PowerAdjusting the volume Selecting an input signalOperating Temporarily muting the soundSearching an input signal Adjusting the zoom and focusSelecting an input signal  For a video signal/no signal 43  169  SmallUsing the automatic adjustment feature Adjusting the position For an RGB signal  For a video signal or s-video signalUsing the magnify feature Correcting the keystone distortionsFreezing the screen Temporarily blanking the screenUSB mouse and keyboard control Available function Remote control operationOperating the computer screen Multifunctional settings Using the menu functionEasy Menu Advanced MenuEasy Menu Reset Easy MenuMirror Filter TimePicture Menu GammaPicture Menu High  Middle  LOW  CustomColor Temp SecamTV  Film  Turn OFF ProgressiveLOAD1  LOAD2  LOAD3  LOAD4 SAVE4 SAVE3  SAVE2  SAVE1Phase Image MenuOver Scan PositionAuto Adjust Image MenuSize ExecuteInput Menu Color SpaceComponent Video FormatInput Menu InformationAudio Setup MenuVolume Screen Menu Menu PositionOSD Bright Bright  DarkMyScreen Lock Screen MenuStart UP Sync is OUT of Range No Input is DetectedMessage Reset  Cancel Option MenuAuto Search Auto OFFOption Menu Maintenance LampLamp part number = RLC-013 Case of replacement by yourselfLamp Air filter Air filtre PJ656 There is no input signal Internal temperature is risingRelated messages Is out of the response parameter range of this unitRegarding the indicator lamps Regarding the indicator lamps It is time to clean the air filterCooling fan is not operating There is a possibility that the interior portionElectrical power cord is not plugged Power switch is not set to the on positionSignal cables are not correctly connected Signal source does not correctly workSignal cables are not correctly connected Volume is adjusted to an extremely low levelAudio setting is not correct Color settings are not correctly adjustedNot properly adjusted Either the focus and/or horizontal phase settings areWhisper function is working Lamp is approaching the end of its product LifetimeSpecification RGB input Video inputAudio input Communication port Audio outputSpecifications Customer Support Country Web Site =Telephone Mail Region =FaxLimited Warranty ViewSonic Projector What the warranty covers
Top Page Image Contents