Eiki LC-SB20 Remote Control Operating Range, Remote Control Batteries Installation, 16.4’ 5 m

Page 15
Remote Control Operating Range

Part Names and Functions

Remote Control Operating Range

Point the remote control toward the projector (Infrared Remote Receiver) whenever pressing any button. Maximum operating range for the remote control is about 16.4’ (5m) and 60° in front of the projector.

16.4’ (5 m)

60°

Remote Control Batteries Installation

1

Remove the battery

compartment lid.

Press the lid down- ward and slide it.

2

Slide the batteries into

3

Replace the compartment

the compartment.

lid.

Two AA size batteries For correct polarity (+ and

–), be sure battery terminals are in contact with pins in compartment.

To insure safe operation, please observe the following precautions :

Use (2) AA, UM3 or R06 type alkaline batteries.

Replace two batteries at the same time.

Do not use a new battery with a used battery.

Avoid contact with water or liquid.

Do not expose the remote control to moisture, or heat.

Do not drop the remote control.

If a battery has leaked on remote control, carefully wipe case clean and install new batteries.

Risk of explosion if battery is replaced by an incorrect type.

Dispose of used batteries according to the instructions.

15

Image 15
Contents MULTIMEDIA PROJECTOR MODEL LC-XB25 LC-XB20 LC-SB20Table of Contents Safety Precaution To the OwnerRISK OF ELECTRIC SHOCK DO NOT OPEN Safety Instructions Voor de klanten in NederlandBij dit product zijn batterijen geleverd Moving the Projector Safety InstructionsInstalling the Projector in Proper Position Air CirculationAC POWER CORD REQUIREMENT ComplianceFederal Communication Commission Notice Connecting the AC Power Cord ComplianceProjector side AC Outlet sideFeatures and Design Bottom Part Names and FunctionsFront BackPart Names and Functions Terminalu i o This projector has control buttons and indicators on its top Remote Control Pointer Function Laser Pointer FunctionWhile pressing the MENU button, press the IMAGE button Remote Control CodeWireless Mouse Operation To initialize the remote control code for the remote controlRemote Control Operating Range Remote Control Batteries Installation16.4’ 5 m 300” InstallationAdjustable Feet Positioning the ProjectorThis terminal is switchable. Set the terminal InstallationConnecting to a Computer USB Cable MAC Adapter When connecting to Macintosh computerSelect COMPUTER 2 in the Setting Menu when the Connecting to Video Equipmentcondition of connecting both the S-VIDEO jack and the VIDEO jack when selecting AUTO in the Input MenuBasic Operation Turning On the ProjectorTurning Off the Projector Basic Operation Zoom AdjustmentFocus Adjustment Keystone AdjustmentVolume P-Timer FunctionSound Adjustment No Show FunctionOn-Screen Menu On-Screen MenuRemote Control Top ControlSharpness / Gamma p30 Menu Barvolume or mute image level amongComputer Computer InputInput Source Selection INPUT button Computer Computer Video COMPUTER button ComputerComputer Input Computer System SelectionPC System Menu Computer Adjustment Auto To store adjustment dataAuto PC Adj Horizontal Computer Adjustment ManualFine sync Total dotsDisplay area ResetDisplay area To store adjustment data To clear adjustment dataIMAGE 1~4 Image Level SelectionStandard RealBrightness Image Level AdjustmentImage Adjust Menu ContrastWide Screen Size AdjustmentNormal TrueAuto Video InputInput Source Selection Video, S-Video INPUT button Video Computer Computer VIDEO button VideoVideo Input Input Source Selection Component, RGB Scart 21-PinINPUT button Computer Computer Video COMPUTER button Computer AV System Menu Video or S-Video Video System SelectionCOMPONENT VIDEO SIGNAL FORMAT PAL / SECAM / NTSC / NTSC4.43 / PAL-M / PAL-NCinema IMAGE button Standard Cinema Image Image ImageImage Color TintProgressive Store Language SettingSetting Setting Menu LanguageRear SettingPower management CeilingFactory default Remote controlPointer Remote control Lamp counter resetThe projector is shut down and the WARNING indicator lights red Maintenance and CleaningWarning Indicator The projector is shut down and the WARNING indicator is flashing redCleaning the Projector Cabinet Maintenance and CleaningCleaning the Air Filters Cleaning the Projection LensReset the Lamp replace counter Lamp ReplacementORDER REPLACEMENT LAMP Replacement Lamp Type NoLAMP HANDLING PRECAUTIONS Lamp Replace CounterSome displays are not seen during the Operation TroubleshootingAppendix Problem No power Image is out of focus No image No soundAppendix Problem Computer 2 cannot be selectedThe Terminal item cannot be selected The Remote Control does not work Indicators Indicators and Projector ConditionProjector Condition Input Menu TreePC Adjust Image Select Image Adjust ScreenScreen 575pSettingImage Adjust Image SelectV-Freq Compatible Computer SpecificationsRESOLUTION H-FreqTechnical Specifications COMPUTER INPUT/COMPONENT INPUT/MONITOR OUTPUT TERMINAL ANALOG Configurations of TerminalsTerminal HDB15-PIN Pin Configuration Terminal DVI-I Pin ConfigurationOptional Parts Terminal Mini DIN 8-PIN Pin ConfigurationPin Configuration Hole Attaching the Lens CoverLens Cover String for the lens cover Secure it to the hole with a screwPage Deutschland & Österreich A-key to better communicationsU.S.A Canada