Eiki LC-SB20, LC-XB25 Setting, Ceiling, Rear, Terminal, Standby mode, Power management, On start

Page 39
Setting

Setting

Ceiling Ceiling

When this function is “On,” the picture is top/bottom and left/right reversed. This function is used to project the image from a ceiling mounting the projector.

Rear Rear

When this function is “On,” the picture is left/right reversed. This function is used to project the image to a rear projection screen.

Terminal Terminal

The COMPUTER IN 2/COMPONENT IN/MONITOR OUT terminal on the back of the projector can be used as computer input or monitor output by switching Terminal with the Point Left/Right button.

To use the terminal as computer input, Component video input, or RGB Scart 21-Pin Video input, select Computer 2. To use the terminal as monitor out, select Monitor out.

Terminal cannot be switched into Monitor out after selecting Computer 2. In this case, select other input source such as Computer 1 or Video, and you will select Terminal.

Standby mode Standby mode

This function is available when using Multi Card Imager optionally supplied, and it reduces standby energy when selecting Eco.

Eco

···· reduces standby energy.

Normal ···· consumes normal standby energy.

Power management

For reducing power consumption as well as maintaining the lamp life, the Power management function turns off the projection lamp when the input signal is interrupted and no button is pressed for 30 seconds or more.

When the input signal is interrupted and no button is pressed for 30 seconds or more, the timer display with the message "No signal" appears on the screen. The count-down starts for the time to have been set. The count-down time can be set between 1 and 30 minutes.

When the count-down time has elapsed, the lamp will be turned off to cool itself down. The POWER indicator is flashing red during this cooling-off period. The next performance depends on setting as follows.

Ready ······ When the lamp has been fully cooled down, the POWER indicator changes to green flashing. In this condition, the projection lamp will be turned on if the input signal is reconnected or any button on the top control or remote control is pressed.

Shutdown···· When the lamp has been fully cooled down, the power will be turned off.

Off ···············The Power management function is canceled.

On start

When this function is “On,” the projector is automatically turned on just by connecting the AC power cord to a wall outlet.

NOTE

●Be sure to turn the projector off properly (see “Turning Off the Projector” on page 19). If the projector is turned off in the wrong steps, the On start function does not operate properly.

Ceiling

Rear

Standby mode

Press the SELECT button at this icon to display other items.

Power management

Time left until Lamp

off

Press the SELECT button at Power management and this box appears. Choose one of three settings with the Point Left/Right button, and go to the timer with the Point Up/Down button and set time with the Point Left/Right button.

39

Page 38 Page 40
Image 39
Page 38 Page 40
Contents MULTIMEDIA PROJECTOR MODEL LC-XB25 LC-XB20 LC-SB20Table of Contents Safety Precaution To the OwnerRISK OF ELECTRIC SHOCK DO NOT OPEN Safety Instructions Voor de klanten in NederlandBij dit product zijn batterijen geleverd Moving the Projector Safety InstructionsInstalling the Projector in Proper Position Air CirculationAC POWER CORD REQUIREMENT ComplianceFederal Communication Commission Notice Connecting the AC Power Cord ComplianceProjector side AC Outlet sideFeatures and Design Bottom Part Names and FunctionsFront BackPart Names and Functions Terminalu i o This projector has control buttons and indicators on its top Remote Control Pointer Function Laser Pointer FunctionWhile pressing the MENU button, press the IMAGE button Remote Control CodeWireless Mouse Operation To initialize the remote control code for the remote controlRemote Control Operating Range Remote Control Batteries Installation16.4’ 5 m 300” InstallationAdjustable Feet Positioning the ProjectorThis terminal is switchable. Set the terminal InstallationConnecting to a Computer USB Cable MAC Adapter When connecting to Macintosh computerSelect COMPUTER 2 in the Setting Menu when the Connecting to Video Equipmentcondition of connecting both the S-VIDEO jack and the VIDEO jack when selecting AUTO in the Input MenuBasic Operation Turning On the ProjectorTurning Off the Projector Basic Operation Zoom AdjustmentFocus Adjustment Keystone AdjustmentVolume P-Timer FunctionSound Adjustment No Show FunctionOn-Screen Menu On-Screen MenuRemote Control Top ControlSharpness / Gamma p30 Menu Barvolume or mute image level amongComputer Computer InputInput Source Selection INPUT button Computer Computer Video COMPUTER button ComputerComputer Input Computer System SelectionPC System Menu Computer Adjustment Auto To store adjustment dataAuto PC Adj Horizontal Computer Adjustment ManualFine sync Total dotsDisplay area ResetDisplay area To store adjustment data To clear adjustment dataIMAGE 1~4 Image Level SelectionStandard RealBrightness Image Level AdjustmentImage Adjust Menu ContrastWide Screen Size AdjustmentNormal TrueAuto Video InputInput Source Selection Video, S-Video INPUT button Video Computer Computer VIDEO button VideoVideo Input Input Source Selection Component, RGB Scart 21-PinINPUT button Computer Computer Video COMPUTER button Computer AV System Menu Video or S-Video Video System SelectionCOMPONENT VIDEO SIGNAL FORMAT PAL / SECAM / NTSC / NTSC4.43 / PAL-M / PAL-NCinema IMAGE button Standard Cinema Image Image ImageImage Color TintProgressive Store Language SettingSetting Setting Menu LanguageRear SettingPower management CeilingFactory default Remote controlPointer Remote control Lamp counter resetThe projector is shut down and the WARNING indicator lights red Maintenance and CleaningWarning Indicator The projector is shut down and the WARNING indicator is flashing redCleaning the Projector Cabinet Maintenance and CleaningCleaning the Air Filters Cleaning the Projection LensReset the Lamp replace counter Lamp ReplacementORDER REPLACEMENT LAMP Replacement Lamp Type NoLAMP HANDLING PRECAUTIONS Lamp Replace CounterSome displays are not seen during the Operation TroubleshootingAppendix Problem No power Image is out of focus No image No soundAppendix Problem Computer 2 cannot be selectedThe Terminal item cannot be selected The Remote Control does not work Indicators Indicators and Projector ConditionProjector Condition Input Menu TreePC Adjust Image Select Image Adjust ScreenScreen 575pSettingImage Adjust Image SelectV-Freq Compatible Computer SpecificationsRESOLUTION H-FreqTechnical Specifications COMPUTER INPUT/COMPONENT INPUT/MONITOR OUTPUT TERMINAL ANALOG Configurations of TerminalsTerminal HDB15-PIN Pin Configuration Terminal DVI-I Pin ConfigurationOptional Parts Terminal Mini DIN 8-PIN Pin ConfigurationPin Configuration Hole Attaching the Lens CoverLens Cover String for the lens cover Secure it to the hole with a screwPage Deutschland & Österreich A-key to better communicationsU.S.A Canada
Top Page Image Contents