Eiki LC-XB25 Installation, Positioning the Projector, Adjustable Feet, 300”, 195”, 150”, 127”

Page 16
Installation

Installation

Positioning the Projector

This projector is designed to project on a flat projection surface and can be focused from 3.3’(1.0m) - 25.3’(7.7m). Refer to the figure and the table below for the screen size and the distance between the projector and the screen.

A : B = 9 : 1

 

25.3' (7.7m)

 

 

 

 

300”

(Inch Diagonal)

 

16.4' (5.0m)

 

 

 

12.5' (3.8m)

Max. Zoom

 

 

195”

 

8.2' (2.5m)

195”

 

 

 

3.3' (1.0m)

150”

Min. Zoom

A

 

127”

100”

 

 

 

 

 

97”

 

 

40”

64”

 

 

 

 

 

 

 

 

(Center)

 

 

 

B

Screen Size

 

40”

 

100”

150”

195”

300”

(W x H) mm

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

813 x 610

 

2032 x 1524

3048 x 2286

3962 x 2972

6096 x 4572

4 : 3 aspect ratio

 

 

 

 

 

 

 

 

 

 

Zoom (min)

 

4.9' (1.5m)

 

12.8' (3.9m)

19.3' (5.9m)

25.3' (7.7m)

––-––

 

 

 

 

 

 

 

 

Zoom (max)

 

3.3' (1.0m)

 

8.2' (2.5m)

12.5' (3.8m)

16.4' (5.0m)

25.3' (7.7m)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

NOTE

The brightness in a room has a great influence on picture quality. It is recommended to limit ambient lighting in order to provide the best image.

The values shown are approximate and may vary from the actual size.

Adjustable Feet

Projection angle can be adjusted up to 11.8 degrees with the adjustable feet.

1

Lift the front of the projector and pull the feet lock latches on

 

both sides of the projector.

2

Release the feet lock latches to lock the adjustable feet and

 

rotate the adjustable feet to adjust the position and tilt.

3

To retract the adjustable feet, lift the front of the projector

 

and pull and undo the feet lock latches.

Keystone distortion of the projected image can be adjusted by menu operation. (p20, 38)

CAUTION

Tilt the projector within the adjustable range in order not to shorten the life of the lamp. Proper angle should be taken. See page 5.

Feet Lock Latches

Adjustable Feet

16

Image 16
Contents MODEL LC-XB25 LC-XB20 LC-SB20 MULTIMEDIA PROJECTORTable of Contents To the Owner Safety PrecautionRISK OF ELECTRIC SHOCK DO NOT OPEN Voor de klanten in Nederland Safety InstructionsBij dit product zijn batterijen geleverd Safety Instructions Installing the Projector in Proper PositionAir Circulation Moving the ProjectorCompliance AC POWER CORD REQUIREMENTFederal Communication Commission Notice Compliance Projector sideAC Outlet side Connecting the AC Power CordFeatures and Design Part Names and Functions FrontBack BottomTerminal Part Names and Functionsu i o This projector has control buttons and indicators on its top Remote Control Laser Pointer Function Pointer FunctionRemote Control Code Wireless Mouse OperationTo initialize the remote control code for the remote control While pressing the MENU button, press the IMAGE buttonRemote Control Batteries Installation Remote Control Operating Range16.4’ 5 m Installation Adjustable FeetPositioning the Projector 300”Installation Connecting to a ComputerUSB Cable MAC Adapter When connecting to Macintosh computer This terminal is switchable. Set the terminalConnecting to Video Equipment condition of connecting both the S-VIDEO jack and the VIDEOjack when selecting AUTO in the Input Menu Select COMPUTER 2 in the Setting Menu when theTurning On the Projector Basic OperationTurning Off the Projector Zoom Adjustment Focus AdjustmentKeystone Adjustment Basic OperationP-Timer Function Sound AdjustmentNo Show Function VolumeOn-Screen Menu Remote ControlTop Control On-Screen MenuMenu Bar volume or muteimage level among Sharpness / Gamma p30Computer Input Input Source SelectionINPUT button Computer Computer Video COMPUTER button Computer ComputerComputer System Selection Computer InputPC System Menu To store adjustment data Computer Adjustment AutoAuto PC Adj Computer Adjustment Manual Fine syncTotal dots HorizontalReset Display area To store adjustment dataTo clear adjustment data Display areaImage Level Selection StandardReal IMAGE 1~4Image Level Adjustment Image Adjust MenuContrast BrightnessScreen Size Adjustment NormalTrue WideVideo Input Input Source Selection Video, S-VideoINPUT button Video Computer Computer VIDEO button Video AutoInput Source Selection Component, RGB Scart 21-Pin Video InputINPUT button Computer Computer Video COMPUTER button Computer Video System Selection COMPONENT VIDEO SIGNAL FORMATPAL / SECAM / NTSC / NTSC4.43 / PAL-M / PAL-N AV System Menu Video or S-VideoIMAGE button Standard Cinema Image Image Image CinemaImage Tint ColorProgressive Screen Size Adjustment Setting SettingSetting Menu Language LanguageSetting Power managementCeiling RearRemote control Pointer Remote controlLamp counter reset Factory defaultMaintenance and Cleaning Warning IndicatorThe projector is shut down and the WARNING indicator is flashing red The projector is shut down and the WARNING indicator lights redMaintenance and Cleaning Cleaning the Air FiltersCleaning the Projection Lens Cleaning the Projector CabinetLamp Replacement ORDER REPLACEMENT LAMPReplacement Lamp Type No Reset the Lamp replace counterLamp Replace Counter LAMP HANDLING PRECAUTIONSTroubleshooting AppendixProblem No power Image is out of focus No image No sound Some displays are not seen during the OperationProblem Computer 2 cannot be selected AppendixThe Terminal item cannot be selected The Remote Control does not work Indicators and Projector Condition IndicatorsProjector Condition Menu Tree PC AdjustImage Select Image Adjust Screen Input575pSetting Image AdjustImage Select ScreenCompatible Computer Specifications RESOLUTIONH-Freq V-FreqTechnical Specifications Configurations of Terminals Terminal HDB15-PIN Pin ConfigurationTerminal DVI-I Pin Configuration COMPUTER INPUT/COMPONENT INPUT/MONITOR OUTPUT TERMINAL ANALOGTerminal Mini DIN 8-PIN Pin Configuration Optional PartsPin Configuration Attaching the Lens Cover Lens Cover String for the lens coverSecure it to the hole with a screw HolePage A-key to better communications U.S.ACanada Deutschland & Österreich