Eiki LC-XB20, LC-SB20, LC-XB25 owner manual Indicators and Projector Condition, Appendix

Page 47

Indicators and Projector Condition

Appendix

Indicators and Projector Condition

Check the indicators for projector condition.

Indicators

	WARNING	LAMP	Projector Condition
POWER	WARNING	REPLACE
red/green	red	yellow

			The projector is OFF. (The AC power cord is unplugged.)

		✽	The projector is preparing for stand-by or the projection lamp is being
		✽	cooled down. The projector cannot be turned on until cooling is completed.


		✽	The projector is ready to be turned on with the POWER ON-OFF button.

		✽	The projector is operating normally.

		✽	The projector is in the Power management mode.

The temperature inside the projector is abnormally high. The projector can- not be turned on. When the projector is cooled down enough and the

✽temperature returns to normal, the POWER indicator lights red and the pro- jector can be turned on. (The WARNING indicator keeps flashing.) Check and clean the Air filter.

The projector has been cooled down enough and the temperature returns

✽to normal. When turning on the projector, the WARNING indicator stops flashing. Check and clean the air filters.

The projector detects an abnormal condition and cannot be turned on. Unplug the AC power cord and plug it again to turn on the projector. If the

✽projector is turned off again, disconnect the AC power cord and contact the dealer or the service center for service and checkup. Do not leave the pro- jector on. It may cause electric shock or a fire hazard.

• • • lights green.

• • • flashes green.

• • • lights red.

• • • flashes red.

• • • off

✽When the life of the projection lamp draws to an end, the LAMP REPLACE indicator lights yellow. When this indicator lights yellow, replace the projection lamp with a new one promptly. Reset the Lamp replace counter after replacement of the lamp. See page 43 and 44.

47

Image 47

Contents MULTIMEDIA PROJECTOR MODEL LC-XB25 LC-XB20 LC-SB20Table of Contents RISK OF ELECTRIC SHOCK DO NOT OPEN Safety PrecautionTo the Owner Bij dit product zijn batterijen geleverd Safety InstructionsVoor de klanten in Nederland Moving the Projector Safety InstructionsInstalling the Projector in Proper Position Air CirculationFederal Communication Commission Notice AC POWER CORD REQUIREMENTCompliance Connecting the AC Power Cord ComplianceProjector side AC Outlet sideFeatures and Design Bottom Part Names and FunctionsFront Backu i o Part Names and FunctionsTerminal This projector has control buttons and indicators on its top Remote Control Pointer Function Laser Pointer FunctionWhile pressing the MENU button, press the IMAGE button Remote Control CodeWireless Mouse Operation To initialize the remote control code for the remote control16.4’ 5 m Remote Control Operating RangeRemote Control Batteries Installation 300” InstallationAdjustable Feet Positioning the ProjectorThis terminal is switchable. Set the terminal InstallationConnecting to a Computer USB Cable MAC Adapter When connecting to Macintosh computerSelect COMPUTER 2 in the Setting Menu when the Connecting to Video Equipmentcondition of connecting both the S-VIDEO jack and the VIDEO jack when selecting AUTO in the Input MenuTurning Off the Projector Basic OperationTurning On the Projector Basic Operation Zoom AdjustmentFocus Adjustment Keystone AdjustmentVolume P-Timer FunctionSound Adjustment No Show FunctionOn-Screen Menu On-Screen MenuRemote Control Top ControlSharpness / Gamma p30 Menu Barvolume or mute image level amongComputer Computer InputInput Source Selection INPUT button Computer Computer Video COMPUTER button ComputerPC System Menu Computer InputComputer System Selection Auto PC Adj Computer Adjustment AutoTo store adjustment data Horizontal Computer Adjustment ManualFine sync Total dotsDisplay area ResetDisplay area To store adjustment data To clear adjustment dataIMAGE 1~4 Image Level SelectionStandard RealBrightness Image Level AdjustmentImage Adjust Menu ContrastWide Screen Size AdjustmentNormal TrueAuto Video InputInput Source Selection Video, S-Video INPUT button Video Computer Computer VIDEO button VideoINPUT button Computer Computer Video COMPUTER button Computer Video InputInput Source Selection Component, RGB Scart 21-Pin AV System Menu Video or S-Video Video System SelectionCOMPONENT VIDEO SIGNAL FORMAT PAL / SECAM / NTSC / NTSC4.43 / PAL-M / PAL-NImage CinemaIMAGE button Standard Cinema Image Image Image Progressive ColorTint Store Language SettingSetting Setting Menu LanguageRear SettingPower management CeilingFactory default Remote controlPointer Remote control Lamp counter resetThe projector is shut down and the WARNING indicator lights red Maintenance and CleaningWarning Indicator The projector is shut down and the WARNING indicator is flashing redCleaning the Projector Cabinet Maintenance and CleaningCleaning the Air Filters Cleaning the Projection LensReset the Lamp replace counter Lamp ReplacementORDER REPLACEMENT LAMP Replacement Lamp Type NoLAMP HANDLING PRECAUTIONS Lamp Replace CounterSome displays are not seen during the Operation TroubleshootingAppendix Problem No power Image is out of focus No image No soundThe Terminal item cannot be selected The Remote Control does not work AppendixProblem Computer 2 cannot be selected Projector Condition IndicatorsIndicators and Projector Condition Input Menu TreePC Adjust Image Select Image Adjust ScreenScreen 575pSettingImage Adjust Image SelectV-Freq Compatible Computer SpecificationsRESOLUTION H-FreqTechnical Specifications COMPUTER INPUT/COMPONENT INPUT/MONITOR OUTPUT TERMINAL ANALOG Configurations of TerminalsTerminal HDB15-PIN Pin Configuration Terminal DVI-I Pin ConfigurationPin Configuration Optional PartsTerminal Mini DIN 8-PIN Pin Configuration Hole Attaching the Lens CoverLens Cover String for the lens cover Secure it to the hole with a screwPage Deutschland & Österreich A-key to better communicationsU.S.A Canada