Intel IMB200VGE user manual Installing ATX Power Supply, Installing the Memory

Page 24

IMB200 LGA775 ATX MB User Manual

3.2Installing ATX Power Supply

System power was provided for the IMB200 Industrial motherboard by CN31

3.3 Installing the Memory

The IMB200 support Dual Channel DDR 266/333/400 memory and support the maximum memory capacity could up to 4GB.

If you want to know what is difference between DDR and DDR2.See below picture

PS: IMB200 only support Un-Buffered DIMM and could not support ECC/Registered DIMM

18	Installation

Image 24

Contents IMB200 Disclaimers ESD Precautions Jumpers and Connectors InstallationChapter Introduction Hardware DescriptionInstalling VGA driver Chapter Installing LAN DriverChapter Award Bios Utility P e n d i x a Watchdog Timer P e n d i x B PCI IRQ RoutingPage Introduction General DescriptionSpecifications ¾ CPU Socket LGA775Utilities Supported Ordering informationBoard Dimensions Jumpers and Connectors Board LayoutJumper Settings Jumper Default Setting Jumper SettingClear Cmos Setting JP7 CF Power Setting JP9 Connectors CN7PCI1~ Installation CPU InstallationInstallation Installation Installation Installation Installation Installation Installing ATX Power Supply Installing the MemoryInstallation General Output Connector CN37 Hardware DescriptionEnhance IDE1/IDE2 connecotor-IDE1 and IDE2 Floppy Disk Connector-FDD Display interface-CN1Parallel Port Connector COM1 Port Connector-CN2 Hardware Description Hardware Description USB USB USB USB Serial ATA Connectors-CN28/CN29 Hardware Description 16 CD/In Connector-CN9 17 CPU/System FAN Connector- CN23/CN24 Installing VGA driver Driver Disks’ ContentsWindows 2000 VGA Driver Installation IntroductionPage Windows XP VGA Driver Installation Installing LAN Driver FeaturesDrivers Supported Award Bios Utility Bios IntroductionBios Setup Page Standard Cmos Setup Date TimeDrive a type/Drive B type Halt OnAdvanced Bios Features CPU FeatureDelay prior to Thermal Execute Disable BitThermal Management Limited Cupid MaxValQuick Power On Self Test Virus WarningFirst/Second/Third Boot Device Boot Other DeviceBoot Up Floppy Seek Swap Floppy DriveBoot Up NumLock Status Apic ModeAdvanced Chipset Features Darm Timing SelectableActive Precharge Delay Dram RAS# to CAS# DelaySystem Bios Cacheable Video Bios CacheableMemory Hole At 15M-16M AGP Aperture Size MBInit Display First On-Chip VGA On-Board Frame Buffer SizeIntegrated Peripherals On-Chip IDE DeviceOn-Chip Primary PCI IDE IDE Primary Master PIOIDE Primary Slave PIO IDE Primary Master UdmaOnboard Device On-Chip Serial ATAUSB Controller USB 2.0 ControllerUSB Keyboard Support AC97 AudioUart Mode Select UR2 Duplex ModeSuper IO Device Onboard FDC ControllerParallel Port Mode ECP mode Use DMAOnboard Uart 3/4 Onboard Parallel PortOnboard Uart 3/4 IRQ Spread SpectrumPower Management Setup Power ManagementAcpi Function Acpi Suspend TypeSuspend Mode HDD Power DownVideo Off Method Video Off In SuspendPower On function Wake-Up By PCI card„ PWN After PWR-Fail PNP/PCI Configuration PNP OS InstalledReset Configuration Data „ Resource controlled by „ PCI /VGA Palette SnoopPC Health Status Frequency/Voltage Control System FAN2 Speed+3.3V/+5V/+12V/-12V/-5V/VBATV/5VSB CPU Clock RatioLoad Fail-Safe Default Load Optimized DefaultSupervisor/User Password Setting Enter Password Exit Setting Save to Cmos and Exit Y/N? YQuit without saving Y/N? Y P e n d i x a Watchdog Timer P e n d i x B PCI IRQ Routing AppendixC Detailed memory Addess Mapping AppendixD I/O Shield