Intel IMB200VGE user manual Parallel Port Connector

Page 29

IMB200 LGA775 ATX MB User Manual

 

 

 

Current

 

 

4

N/C

5

GND

6

N/C

7

GND

8

Index #

9

GND

10

Motor enable A #

11

GND

12

Drive Select B #

13

GND

14

Drive select A #

15

GND

16

Motor enable B #

17

GND

18

Direction #

19

GND

20

STEP #

21

GND

22

Write data #

23

GND

24

Write gate #

25

GND

26

Track #

27

GND

28

Write protect #

29

GND

30

Read data #

31

GND

32

Side 1 select #

33

GND

34

Disk change #

 

 

 

 

.

 

 

 

 

 

4.5 Parallel Port Connector

zStandard mode: IBM PC/XT, PC/AT and PS/2TM compatible with bi-directional parallel port

zEnhanced mode: Enhance parallel port (EPP) compatible with EPP 1.7 and EPP 1.9 (IEEE 1284 compliant)

zHigh speed mode: Microsoft and Hewlett Packard extended capabilities port (ECP) IEEE 1284 compliant

The address select of the onboard parallel port in LPT1 (3BCH) or disabled is done by BIOS CMOS setup.

Pin

Description

Pin

Description

Hardware Description

23

Page 28 Page 30
Image 29
Page 28 Page 30
Contents IMB200 Disclaimers ESD Precautions Installation Jumpers and ConnectorsChapter Introduction Hardware DescriptionChapter Installing LAN Driver Installing VGA driverChapter Award Bios Utility P e n d i x a Watchdog Timer P e n d i x B PCI IRQ RoutingPage General Description Introduction¾ CPU Socket LGA775 SpecificationsOrdering information Utilities SupportedBoard Dimensions Board Layout Jumpers and ConnectorsJumper Default Setting Jumper Setting Jumper SettingsClear Cmos Setting JP7 CF Power Setting JP9 CN7 ConnectorsPCI1~ CPU Installation InstallationInstallation Installation Installation Installation Installation Installation Installing the Memory Installing ATX Power SupplyInstallation Hardware Description General Output Connector CN37Enhance IDE1/IDE2 connecotor-IDE1 and IDE2 Display interface-CN1 Floppy Disk Connector-FDDParallel Port Connector COM1 Port Connector-CN2 Hardware Description Hardware Description USB USB USB USB Serial ATA Connectors-CN28/CN29 Hardware Description 16 CD/In Connector-CN9 17 CPU/System FAN Connector- CN23/CN24 Driver Disks’ Contents Installing VGA driverWindows 2000 VGA Driver Installation IntroductionPage Windows XP VGA Driver Installation Drivers Supported Installing LAN DriverFeatures Bios Setup Award Bios UtilityBios Introduction Page Standard Cmos Setup Time DateHalt On Drive a type/Drive B typeCPU Feature Advanced Bios FeaturesExecute Disable Bit Delay prior to ThermalThermal Management Limited Cupid MaxValVirus Warning Quick Power On Self TestBoot Other Device First/Second/Third Boot DeviceBoot Up Floppy Seek Swap Floppy DriveApic Mode Boot Up NumLock StatusDarm Timing Selectable Advanced Chipset FeaturesDram RAS# to CAS# Delay Active Precharge DelaySystem Bios Cacheable Video Bios CacheableInit Display First Memory Hole At 15M-16MAGP Aperture Size MB On-Board Frame Buffer Size On-Chip VGAOn-Chip IDE Device Integrated PeripheralsIDE Primary Master PIO On-Chip Primary PCI IDEIDE Primary Slave PIO IDE Primary Master UdmaOn-Chip Serial ATA Onboard DeviceUSB 2.0 Controller USB ControllerUSB Keyboard Support AC97 AudioUR2 Duplex Mode Uart Mode SelectSuper IO Device Onboard FDC ControllerECP mode Use DMA Parallel Port ModeOnboard Uart 3/4 Onboard Parallel PortSpread Spectrum Onboard Uart 3/4 IRQPower Management Power Management SetupAcpi Function Acpi Suspend TypeHDD Power Down Suspend ModeVideo Off Method Video Off In Suspend„ PWN After PWR-Fail Power On functionWake-Up By PCI card Reset Configuration Data PNP/PCI ConfigurationPNP OS Installed „ PCI /VGA Palette Snoop „ Resource controlled byPC Health Status System FAN2 Speed Frequency/Voltage Control+3.3V/+5V/+12V/-12V/-5V/VBATV/5VSB CPU Clock RatioSupervisor/User Password Setting Load Fail-Safe DefaultLoad Optimized Default Enter Password Save to Cmos and Exit Y/N? Y Exit SettingQuit without saving Y/N? Y P e n d i x a Watchdog Timer P e n d i x B PCI IRQ Routing AppendixC Detailed memory Addess Mapping AppendixD I/O Shield
Top Page Image Contents