Intel IMB200VGE user manual Usb Usb Usb Usb

Page 33

IMB200 LGA775 ATX MB User Manual

USB USB USB USB

GND P0+ P0- Power

10

1

2

AGND USB USB USB USB

GND P1+ P1+ Power

4.11 Audio Jack (Line-in/Line-Out/MIC)-CN3

4.12 ATX12V CPU Power Connector: CN14

This connector connected to an ATX12V power supply and used for CPU Core Voltage.

Important Note: Make sure your ATX12V power supply can

provide 16A on the +12V lead and at least 1A on the +5V standby lead (+5VSB). The

Hardware Description

27

Image 33

Contents IMB200 Disclaimers ESD Precautions Installation Jumpers and ConnectorsChapter Introduction Hardware DescriptionChapter Installing LAN Driver Installing VGA driverChapter Award Bios Utility P e n d i x a Watchdog Timer P e n d i x B PCI IRQ RoutingPage General Description Introduction¾ CPU Socket LGA775 SpecificationsOrdering information Utilities SupportedBoard Dimensions Board Layout Jumpers and ConnectorsJumper Default Setting Jumper Setting Jumper SettingsClear Cmos Setting JP7 CF Power Setting JP9 CN7 ConnectorsPCI1~ CPU Installation InstallationInstallation Installation Installation Installation Installation Installation Installing the Memory Installing ATX Power SupplyInstallation Hardware Description General Output Connector CN37Enhance IDE1/IDE2 connecotor-IDE1 and IDE2 Display interface-CN1 Floppy Disk Connector-FDDParallel Port Connector COM1 Port Connector-CN2 Hardware Description Hardware Description USB USB USB USB Serial ATA Connectors-CN28/CN29 Hardware Description 16 CD/In Connector-CN9 17 CPU/System FAN Connector- CN23/CN24 Driver Disks’ Contents Installing VGA driverWindows 2000 VGA Driver Installation IntroductionPage Windows XP VGA Driver Installation Installing LAN Driver FeaturesDrivers Supported Award Bios Utility Bios IntroductionBios Setup Page Standard Cmos Setup Time DateHalt On Drive a type/Drive B typeCPU Feature Advanced Bios FeaturesExecute Disable Bit Delay prior to ThermalThermal Management Limited Cupid MaxValVirus Warning Quick Power On Self TestBoot Other Device First/Second/Third Boot DeviceBoot Up Floppy Seek Swap Floppy DriveApic Mode Boot Up NumLock StatusDarm Timing Selectable Advanced Chipset FeaturesDram RAS# to CAS# Delay Active Precharge DelaySystem Bios Cacheable Video Bios CacheableMemory Hole At 15M-16M AGP Aperture Size MBInit Display First On-Board Frame Buffer Size On-Chip VGAOn-Chip IDE Device Integrated PeripheralsIDE Primary Master PIO On-Chip Primary PCI IDEIDE Primary Slave PIO IDE Primary Master UdmaOn-Chip Serial ATA Onboard DeviceUSB 2.0 Controller USB ControllerUSB Keyboard Support AC97 AudioUR2 Duplex Mode Uart Mode SelectSuper IO Device Onboard FDC ControllerECP mode Use DMA Parallel Port ModeOnboard Uart 3/4 Onboard Parallel PortSpread Spectrum Onboard Uart 3/4 IRQPower Management Power Management SetupAcpi Function Acpi Suspend TypeHDD Power Down Suspend ModeVideo Off Method Video Off In SuspendPower On function Wake-Up By PCI card„ PWN After PWR-Fail PNP/PCI Configuration PNP OS InstalledReset Configuration Data „ PCI /VGA Palette Snoop „ Resource controlled byPC Health Status System FAN2 Speed Frequency/Voltage Control+3.3V/+5V/+12V/-12V/-5V/VBATV/5VSB CPU Clock RatioLoad Fail-Safe Default Load Optimized DefaultSupervisor/User Password Setting Enter Password Save to Cmos and Exit Y/N? Y Exit SettingQuit without saving Y/N? Y P e n d i x a Watchdog Timer P e n d i x B PCI IRQ Routing AppendixC Detailed memory Addess Mapping AppendixD I/O Shield