Intel Raptor AT manual Map, Address hex Description

Page 54

Raptor AT – Installation Guide

I/O Map

	Address (hex)	Description
	0000-000F	DMA 1
	0020-0021	Interrupt Controller 1
	0040	Timer/Counter 0
	0041	Timer/Counter 1
	0042	Timer/Counter 2
	0043	Timer Control Word
	0060	Keyboard Controller Byte _ Reset IRQ
	0061	NMI Status and Control
	0070, bit 7	NMI enable
	0070, bits 6:0	RTC Index
	0071	RTC Data
	0072	RTC Extended Index
	0073	RTC Extended Data
	0080-008F	DMA page registers / POST code display also
	0080-008F	located at 0080h
		located at 0080h
	0092	Port 92
	00A0-00A1	Interrupt Controller 2
	00B2-00B3	APM control
	00C0-00DE	DMA 2
	00F0	Coprocessor Error
	0110	Watch-Dog Timer (default)
	0170 _ 0177	Secondary IDE channel
	01F0 _ 01F7	Primary IDE channel
	029x	LM79
	0278-027F	LPT2 (if selected)
	02E8-02EF	COM4 (if selected)
	02F8-02FF	COM2 (default)
	0310	Watch-Dog Timer (if selected)
	0376	Secondary IDE channel command port
	0377	Floppy channel 2 command
	0377, bit 7	Floppy disk change, channel 2
	0377, bits 6:0	Secondary IDE channel status port
	0378-037F	LPT1 (default)
	03B4-03B5	Video (VGA)
	03BA	Video (VGA)
	03BC-03CD	LPT3 (if selected)
	03C0-03CA	Video (VGA)
	03CC	Video (VGA)
	03CE-03CF	Video (VGA)

44

Image 54

Contents Raptor AT Page Pre-Configuration ChapterAppendix a Technical Specifications Appendix B Flash Bios Programming Appendix C Disk-On-ChipAppendix D On-Board Industrial Appendix E On-BoardRaptor AT Installation Guide System Board Pre-Configuration IntroductionStatic Electricity Warning Memory CPU SupportSupported Bus Clocks On-Board I/OConventions Used in this Manual On-Board EthernetPre-Configuration Static WarningRaptor AT Installation Guide Jumper Types Jumper Locations Jumper LocationsFlash Bios Write Protect Cmos ResetReset Cmos Normal Clear Cmos Flash Write-protect Enabled DisabledClock Speed Selection Watchdog Timer SelectionTimeout Clock JP11Ethernet Selection Enabled Disabled ATX Power Supply EnhancementsAddress 110h Closed Open 310h Raptor AT Memory Configuration CPU InstallationDesigning for thermal performance Fan HeatsinkInstalling Peripheral Cables Disk-on-Chip installationInstalling Cables Power and Control Panel Cables Airflow managementPre-Configuration Location of Components and Connectors Index of Connectors Connector DescriptionUsers Notes Using the Keyboard with Bios Setup SetupStarting Bios Setup Bios Setup Main MenuStandard Setup Date/TimeFloppy Drive A, B Quick Boot Advanced Cmos SetupBoot Sector Virus Protection Pri Master Pri Slave Sec Master Sec SlaveFloppy Access Control Try Other Boot DevicesInitial Display Mode Hard Disk Access ControlFloppy Drive Swap Boot Up Num LockA.R.T. for Hard Disks Floppy Drive SeekWait for F1 If Error Password CheckBoot to OS/2 Primary DisplayInternal Cache Advanced Chipset SetupSystem Bios Cacheable C000,16K Shadow C400,16K ShadowPCI 1 to PCI 0 Access BX/GX Master Latency Timer ClksMulti-Trans Timer Clks USB KB/Mouse Legacy SupportDram Integrity Mode Aperture Access Global EnablePCI 0 Agent to Aperture Access Memory Autosizing Support Sdram RAS# to CAS# Delay16bit I/O Recovery Time Power Down SdramSearch for MDA Resources Bit I/O Recovery Time Sdram Precharge ControlPower Management Setup Green PC Monitor Power State Power Management/APMPower button Function Video Power Down ModeStandby Timeout Power Saving TypeStandby / Suspend Timer Unit Suspend TimeoutLAN Wake-Up PCI/Plug and Play SetupPCI Latency Timer PCI Clocks Plug and Play Aware OSPCI IDE Bus Master PCI VGA Palette SnoopAllocate IRQ to PCI VGA Off-board PCI IDE CardOff-board PCI IDE Secondary IRQ DMA ChannelReserved Memory Address Peripheral SetupReserved Memory Size PCI Device Search OrderParallel Port Mode Serial Port2 ModeInfra-Red Transmission Mode Onboard Serial Port1EPP Version CPU Current TemperatureCPU Overheat Warning Temperature Parallel Port IRQCPU Fan Secondary Fan Change User PasswordAuto Detect Hard Disk Onboard IDEChange Supervisor Password Auto Configuration with Fail-Safe Settings Save Settings and ExitExit without Saving Chapter Upgrading Upgrading the System MemoryUpgrading the Microprocessor Users Notes Bios Appendix aSystem Memory Embedded I/O Industrial Devices MiscellaneousForm Factor Control Panel ConnectionsCPU Socket PCB ConstructionAddress Range Size Description Decimal Hexadecimal Memory MapDMA Channels Data Width System ResourceMap Address hex DescriptionPCI Configuration Space Map On-board DevicesBus # Device # Function # Description Signal InterruptsPCI Interrupt Routing Map Connectors Pin-out Device Slave AddressPin# Serial Ports DB9M J36 and J37 Ethernet Header J31Pin# Parallel DB25F J13 Pin#HDD LED Appendix B Flash Bios Programming Beeps Description Appendix C Disk-On-Chip Users Notes Software Reset Watchdog TimerHardware Reset Appendix D On-Board Industrial DevicesAddress Post Code DisplayPost Checkpoint Codes Checkpoint Description CodeTable D-5 Bootblock Recovery Codes Table D-6 Uncompressed Initialization Codes Memory refresh line is toggling. Checking 3Ah Performing the DMA controller 2 base register test next Winbios Adaptor ROM had control and has now returned Table D-7 Bus Checkpoint Codes Bits Description Appendix E On-Board Ethernet Users Notes Page MN-RBXAT-03