Intel Raptor AT manual PCI VGA Palette Snoop, Allocate IRQ to PCI VGA, PCI IDE Bus Master

Page 39

Chapter 2:BIOS Configuration

96, 128, 160, 192, 224 and 248. The Optimal and Fail-Safe default setting is 64.

PCI VGA Palette Snoop

This option must be set to Enabled if any ISA adapter card installed in the computer requires VGA palette snooping. The setting is either Disabled or Enabled. The default setting is Disabled.

Allocate IRQ to PCI VGA

This option determines if the BIOS should assign an IRQ to the VGA card. The settings are either Yes or No. The default setting is No.

PCI IDE Bus Master

Set this option to Enabled to specify that the IDE controller on the PCI local bus has bus mastering capability. The setting is either Disabled or Enabled. The default setting is Disabled.

Off-board PCI IDE Card

This option specifies if an off-board PCI IDE controller adapter card is used in the computer. You must also specify the PCI expansion slot on the motherboard where the off-board PCI IDE controller card is installed. If an off-board PCI IDE controller is used, the onboard IDE controller on the CPU board is automatically disabled. The settings are Auto (default), Slot1, Slot2, Slot3, Slot4, Slot5 and Slot6. If Auto is selected, AMIBIOS automatically determines the correct setting for this option.

Off-board PCI IDE Primary IRQ

This option specifies the PCI interrupt used by the primary IDE channel on the off-board PCI IDE controller. The settings are: Disabled, INTA, INTB, INTC, INTD and Hardwired. The Optimal and Fail-Safe default setting is Disabled.

29

Image 39

Contents Raptor AT Page Chapter Pre-ConfigurationAppendix B Flash Bios Programming Appendix C Disk-On-Chip Appendix a Technical SpecificationsAppendix E On-Board Appendix D On-Board IndustrialRaptor AT Installation Guide Introduction System Board Pre-ConfigurationStatic Electricity Warning On-Board I/O CPU SupportSupported Bus Clocks MemoryOn-Board Ethernet Conventions Used in this ManualStatic Warning Pre-ConfigurationRaptor AT Installation Guide Jumper Types Jumper Locations Jumper LocationsFlash Write-protect Enabled Disabled Cmos ResetReset Cmos Normal Clear Cmos Flash Bios Write ProtectClock JP11 Watchdog Timer SelectionTimeout Clock Speed SelectionEthernet Selection Enabled Disabled ATX Power Supply EnhancementsAddress 110h Closed Open 310h CPU Installation Raptor AT Memory ConfigurationFan Heatsink Designing for thermal performanceAirflow management Disk-on-Chip installationInstalling Cables Power and Control Panel Cables Installing Peripheral CablesPre-Configuration Location of Components and Connectors Connector Description Index of ConnectorsUsers Notes Bios Setup Main Menu SetupStarting Bios Setup Using the Keyboard with Bios SetupStandard Setup Date/TimeFloppy Drive A, B Pri Master Pri Slave Sec Master Sec Slave Advanced Cmos SetupBoot Sector Virus Protection Quick BootHard Disk Access Control Try Other Boot DevicesInitial Display Mode Floppy Access ControlFloppy Drive Seek Boot Up Num LockA.R.T. for Hard Disks Floppy Drive SwapPrimary Display Password CheckBoot to OS/2 Wait for F1 If ErrorC000,16K Shadow C400,16K Shadow Advanced Chipset SetupSystem Bios Cacheable Internal CacheUSB KB/Mouse Legacy Support BX/GX Master Latency Timer ClksMulti-Trans Timer Clks PCI 1 to PCI 0 AccessSdram RAS# to CAS# Delay Aperture Access Global EnablePCI 0 Agent to Aperture Access Memory Autosizing Support Dram Integrity ModeSdram Precharge Control Power Down SdramSearch for MDA Resources Bit I/O Recovery Time 16bit I/O Recovery TimePower Management Setup Video Power Down Mode Power Management/APMPower button Function Green PC Monitor Power StateSuspend Timeout Power Saving TypeStandby / Suspend Timer Unit Standby TimeoutPlug and Play Aware OS PCI/Plug and Play SetupPCI Latency Timer PCI Clocks LAN Wake-UpOff-board PCI IDE Card PCI VGA Palette SnoopAllocate IRQ to PCI VGA PCI IDE Bus MasterDMA Channel Off-board PCI IDE Secondary IRQPCI Device Search Order Peripheral SetupReserved Memory Size Reserved Memory AddressOnboard Serial Port1 Serial Port2 ModeInfra-Red Transmission Mode Parallel Port ModeParallel Port IRQ CPU Current TemperatureCPU Overheat Warning Temperature EPP VersionOnboard IDE Change User PasswordAuto Detect Hard Disk CPU Fan Secondary FanChange Supervisor Password Auto Configuration with Fail-Safe Settings Save Settings and ExitExit without Saving Chapter Upgrading Upgrading the System MemoryUpgrading the Microprocessor Users Notes Bios Appendix aSystem Memory Embedded I/O Miscellaneous Industrial DevicesPCB Construction Control Panel ConnectionsCPU Socket Form FactorData Width System Resource Memory MapDMA Channels Address Range Size Description Decimal HexadecimalAddress hex Description MapPCI Configuration Space Map On-board DevicesBus # Device # Function # Description Signal InterruptsPCI Interrupt Routing Map Device Slave Address Connectors Pin-outEthernet Header J31 Pin# Serial Ports DB9M J36 and J37Pin# Pin# Parallel DB25F J13HDD LED Appendix B Flash Bios Programming Beeps Description Appendix C Disk-On-Chip Users Notes Appendix D On-Board Industrial Devices Watchdog TimerHardware Reset Software ResetPost Code Display AddressCheckpoint Description Code Post Checkpoint CodesTable D-5 Bootblock Recovery Codes Table D-6 Uncompressed Initialization Codes Memory refresh line is toggling. Checking 3Ah Performing the DMA controller 2 base register test next Winbios Adaptor ROM had control and has now returned Table D-7 Bus Checkpoint Codes Bits Description Appendix E On-Board Ethernet Users Notes Page MN-RBXAT-03