Intel Raptor AT manual Table D-5 Bootblock Recovery Codes

Page 68

Raptor AT – Installation Guide

Table D-5 Bootblock Recovery Codes

The bootblock recovery checkpoint codes are listed in order of execution:

 

Checkpoint

 

 

 

Description

 

Code

 

 

 

 

 

 

 

 

 

E0h

 

The onboard floppy controller if available is initialized.

 

 

Next, beginning the base 512 KB memory test.

 

 

 

 

E1h

 

Initializing the interrupt vector table next.

 

E2h

 

Initializing the DMA and Interrupt controllers next.

 

E6h

 

Enabling the floppy drive controller and Timer IRQs.

 

 

Enabling internal cache memory.

 

 

 

 

EDh

 

Initializing the floppy drive.

 

EEh

 

Looking for a floppy diskette in drive A:. Reading the

 

 

first sector of the diskette.

 

 

 

 

EFh

 

A read error occurred while reading the floppy drive in

 

 

drive A:.

 

 

 

 

 

 

F0h

 

Next, searching for the AMIBOOT.ROM file in the root

 

 

directory.

 

 

 

 

 

 

F1h

 

The AMIBOOT.ROM file is not in the root directory.

 

F2h

 

Next, reading and analyzing the floppy diskette FAT to

 

 

find the clusters occupied by the AMIBOOT.ROM file.

 

 

 

 

F3h

 

Next,

reading

the AMIBOOT.ROM file, cluster by

 

 

cluster.

 

 

 

 

 

 

F4h

 

The AMIBOOT.ROM file is not the correct size.

 

F5h

 

Next, disabling internal cache memory.

 

FBh

 

Next, detecting the type of flash ROM.

 

FCh

 

Next, erasing the flash ROM.

 

FDh

 

Next, programming the flash ROM.

 

FFh

 

Flash

ROM

programming was successful. Next,

 

 

restarting the system BIOS.

 

 

 

58

Image 68
Contents Raptor AT Page Pre-Configuration ChapterAppendix a Technical Specifications Appendix B Flash Bios Programming Appendix C Disk-On-ChipAppendix D On-Board Industrial Appendix E On-BoardRaptor AT Installation Guide System Board Pre-Configuration IntroductionStatic Electricity Warning CPU Support Supported Bus ClocksMemory On-Board I/OConventions Used in this Manual On-Board EthernetPre-Configuration Static WarningRaptor AT Installation Guide Jumper Types Jumper Locations Jumper LocationsCmos Reset Reset Cmos Normal Clear CmosFlash Bios Write Protect Flash Write-protect Enabled DisabledWatchdog Timer Selection TimeoutClock Speed Selection Clock JP11Address 110h Closed Open 310h Ethernet Selection Enabled DisabledATX Power Supply Enhancements Raptor AT Memory Configuration CPU InstallationDesigning for thermal performance Fan HeatsinkDisk-on-Chip installation Installing Cables Power and Control Panel CablesInstalling Peripheral Cables Airflow managementPre-Configuration Location of Components and Connectors Index of Connectors Connector DescriptionUsers Notes Setup Starting Bios SetupUsing the Keyboard with Bios Setup Bios Setup Main MenuFloppy Drive A, B Standard SetupDate/Time Advanced Cmos Setup Boot Sector Virus ProtectionQuick Boot Pri Master Pri Slave Sec Master Sec SlaveTry Other Boot Devices Initial Display ModeFloppy Access Control Hard Disk Access ControlBoot Up Num Lock A.R.T. for Hard DisksFloppy Drive Swap Floppy Drive SeekPassword Check Boot to OS/2Wait for F1 If Error Primary DisplayAdvanced Chipset Setup System Bios CacheableInternal Cache C000,16K Shadow C400,16K ShadowBX/GX Master Latency Timer Clks Multi-Trans Timer ClksPCI 1 to PCI 0 Access USB KB/Mouse Legacy SupportAperture Access Global Enable PCI 0 Agent to Aperture Access Memory Autosizing SupportDram Integrity Mode Sdram RAS# to CAS# DelayPower Down Sdram Search for MDA Resources Bit I/O Recovery Time16bit I/O Recovery Time Sdram Precharge ControlPower Management Setup Power Management/APM Power button FunctionGreen PC Monitor Power State Video Power Down ModePower Saving Type Standby / Suspend Timer UnitStandby Timeout Suspend TimeoutPCI/Plug and Play Setup PCI Latency Timer PCI ClocksLAN Wake-Up Plug and Play Aware OSPCI VGA Palette Snoop Allocate IRQ to PCI VGAPCI IDE Bus Master Off-board PCI IDE CardOff-board PCI IDE Secondary IRQ DMA ChannelPeripheral Setup Reserved Memory SizeReserved Memory Address PCI Device Search OrderSerial Port2 Mode Infra-Red Transmission ModeParallel Port Mode Onboard Serial Port1CPU Current Temperature CPU Overheat Warning TemperatureEPP Version Parallel Port IRQChange User Password Auto Detect Hard DiskCPU Fan Secondary Fan Onboard IDEChange Supervisor Password Exit without Saving Auto Configuration with Fail-Safe SettingsSave Settings and Exit Upgrading the Microprocessor Chapter UpgradingUpgrading the System Memory Users Notes System Memory BiosAppendix a Embedded I/O Industrial Devices MiscellaneousControl Panel Connections CPU SocketForm Factor PCB ConstructionMemory Map DMA ChannelsAddress Range Size Description Decimal Hexadecimal Data Width System ResourceMap Address hex DescriptionBus # Device # Function # Description PCI Configuration Space MapOn-board Devices PCI Interrupt Routing Map SignalInterrupts Connectors Pin-out Device Slave AddressPin# Serial Ports DB9M J36 and J37 Ethernet Header J31Pin# Parallel DB25F J13 Pin#HDD LED Appendix B Flash Bios Programming Beeps Description Appendix C Disk-On-Chip Users Notes Watchdog Timer Hardware ResetSoftware Reset Appendix D On-Board Industrial DevicesAddress Post Code DisplayPost Checkpoint Codes Checkpoint Description CodeTable D-5 Bootblock Recovery Codes Table D-6 Uncompressed Initialization Codes Memory refresh line is toggling. Checking 3Ah Performing the DMA controller 2 base register test next Winbios Adaptor ROM had control and has now returned Table D-7 Bus Checkpoint Codes Bits Description Appendix E On-Board Ethernet Users Notes Page MN-RBXAT-03