Lenovo B6000, B8000 manual Removing and replacing an FRU

Page 31

Lenovo B6000 / B8000

Removing and replacing an FRU

This section presents exploded figures with the instructions to indicate how to remove and replace the FRU. Make sure to observe the following general rules:

1.Do not attempt to service any computer unless you have been trained and certified. An untrained person runs the risk of damaging parts.

2.Before replacing any FRU, review “FRU replacement notices” on page 26.

3.Begin by removing any FRUs that have to be removed before the failing FRU. Any of such FRUs are listed at the top of the page. Remove them in the order in which they are listed.

4.Follow the correct sequence in the steps to remove the FRU, while referring to figures provided in the procedure.

5.When turning a screw to replace an FRU, turn it in the direction as given by the arrow in the figure.

6.When removing the FRU, move it in the direction as given by the arrow in the figure.

7.To put the new FRU in place, reverse the removal procedures and follow any of the notes that pertain to replacement. For information about connecting and arranging internal cables, see “Locations” on page 59.

8.When replacing an FRU, use the correct screw as shown in the procedures.

DANGER

Before removing any FRU, turn off the computer, unplug all power cords from electrical outlets, and then disconnect any of the interconnecting cables.

Attention: After replacing an FRU, do not turn on the computer until you have made sure that all screws, springs, and other small parts are in place and none are loose inside the computer. Verify this by shaking the computer gently and listening for rattling sounds. Metallic parts or metal flakes can cause electrical short circuits.

Attention: The system board is sensitive to, and can be damaged by, electrostatic discharge. Before touching it, establish personal grounding by touching a ground point with one hand or using an electrostatic discharge (ESD) strap (P/N 6405959) to remove potential shock reasons.

Notes:

The two products covered by this manual, namely Lenovo B6000 and

Lenovo B8000, are identical in structure and internal parts.

The illustrations used in this section come from Lenovo B6000-H.

27

Image 31
Contents B6000 / B8000 Page Contents Lenovo B6000 Lenovo B8000 About this manualSafety information General safety Electrical safety Lenovo B6000/B8000 Hardware Maintenance Manual Safety inspection guide Grounding requirements Safety notice Safety notices multilingual translationsLenovo B6000/B8000 Hardware Maintenance Manual Safety information Lenovo B6000/B8000 Hardware Maintenance Manual Safety information Lenovo B6000/B8000 Hardware Maintenance Manual Safety information Laser compliance statement Safety information Strategy for replacing FRUs Before replacing partsImportant notice for replacing a system board Important service informationOriginal part Important information about replacing RoHS compliant FRUsGeneral checkout What to do first Following are not covered under warrantyAccurate information about the battery status Power system checkoutChecking the internal battery status Approximate information about the battery statusLenovo B6000/B8000 Hardware Maintenance Manual Security Power managementActivating/Deactivating the Display Feature Description SpecificationsLenovo B6000 / B8000 Logic card to plastic FRU replacement noticesScrew notices Plastic to plasticRemoving and replacing an FRU Peeling off the label on the rear cover Rear coverSeparating the rear cover using a suction tool Unlocking the central area of the rear cover Step Screw quantity Color Torque Screws on the holder of the speaker box Right speaker boxDisconnecting the speaker FPC Prying off the holder Removing the speaker box Hinge frame and pivot Disconnecting the main FPCRemoving the hinge frame with the main FPC at the left end Removing the hinge pivot Main camera Disconnecting the main camera FPCDetaching the main camera Screws fixing the left speaker box Left speaker boxScrews on the main antenna Main antennaPhillips flat-head, M1.4 × 1.5 Black N/A Screw on the WiFi antenna WiFi antennaWiFi antenna frame detached Important notices for handling PCB Main PcbaRemoving the conductive fiber Removing the USB FPC holder Disconnecting the FPC between the main Pcba and sub board Disconnecting the LCD FPC Removing the adhisive tapes Main Pcba removed 10 Unlock the main antenna FPC connector 12 Main antenna removed Screws on the sub board Sub boardDisconnecting the TP FPC Detaching the vibrator motor Pushing out the power button Power buttonFront view LocationsRear view Parts list Overall Lenovo B6000 / B8000 Parts list-Overall for Lenovo B6000 only Parts list-Overall for Lenovo B8000 only Screw Parts list-ScrewPage Trademarks