Sanyo PLC-XF60A Some displays are not seen, During the Operation Only part of image is displayed

Page 69

Appendix

Some displays are not seen

– Check the Display item. (“Setting” on page 52)

during the Operation.

 

 

 

Only part of image is displayed.

– Check if you are in D. Zoom+/– mode. (p.32, 48)

(Large/Small)

– Change Aspect setting in the Screen setting menu. (p.47)

 

– Adjust Display area and Position in the PC adjust menu. (p.41~42)

PIN code dialog box appears at start-up.– PJ PIN code lock is being set. Input a PIN code (1234 or numbers you have

 

set). (“Enter a PJ PIN Code” on pages 27 and 55)

 

 

Image is not displayed on the

– Select Input 1 with the Input button on the top control or the INPUT 1 button

monitor connected to the ANALOG

on the remote control, or through the Input Menu. (p.30, 36)

OUT terminal.

– Make sure Analog out is “On.” (“Setting” on page 53)

 

 

The Top Control does not work.

– Check if the Keylock function is set. (“Setting” on page 54)

 

 

The Wireless Remote Control

– Check the batteries. When replacing, the two batteries should be replaced

does not work.

at the same time. (p.17)

 

– Make sure no obstruction is between the projector and remote control.

 

– Make sure you are not too far from the projector when using the remote

 

control. Maximum operating range is 32.8’ (10m).

 

– Make sure the ID and CH of the remote control is conformed to the

 

projector. (p.16, 51)

 

– Initialize the remote control ID and CH, and then initialize the remote control

 

ID and CH of the projector as well. (p.16, 51)

 

– Unlock Key lock for the remote control in the Setting Menu. (p.54)

 

– Make sure the wired remote cable is not connected to the projector.

 

(p.25)

 

When all the solutions above fail, try Factory default in the Setting menu.

 

(p.56)

 

 

USB mouse does not operate properly.

– Check cable connection of the USB mouse and the projector. (p.25)

 

 

SHUTTER button does not operate.

– Make sure Shutter protection is “Off.” (“Setting” on page 53)

 

 

Lens position moves when Input

– Check Lens memory for each input. (“Setting” on page 53)

is switched.

 

 

 

Some operating menu items do not appear.

– Check the My menu setting. (“Setting” on page 49)

Appendix

WARNING :

High voltages are used to operate this projector. Do not attempt to open the cabinet.

If problems still persist after following all operating instructions, contact the dealer where you purchased the projector or the service center. Give the model number and explain about the problem. We will advise you how to obtain service.

69

Image 69
Contents Model PLC-XF60A PLC-EF60A Compatibility My Menu Selection Features and DesignTable of Contents Risk of Electric Shock Do not Open To The OwnerVoor de klanten in Nederland Safety InstructionsPositioning Precautions Setup In Proper DirectionsAir Circulation Bottom Front Downward Upward UsualUSE Caution in Carrying or Transporting the Projector Moving the ProjectorFederal Communication Commission Notice ComplianceParts Name PreparationFront BackIndicators Top Control Input 2 terminals TerminalsC Jack USB Series BUSB Serial Port OUTAbout Control Pad Remote Control4REMOTE RESET/ON/ALL-OFF switch Timer buttonFreeze button CH buttonRemote Control Transmitter Remote Control Channel and ID SetupWired Remote Control Transmitter Remote Control Battery Installation Remote Control Channel & FrequencyRemote Control ID Installation InstallationLens Installation Positioning the ProjectorLens Shift Adjustment Level Adjustable FeetAdjustable feet Connecting AC Power Cord 200 240 V ACGround Connection Terminals Interface Board SlotsOption Control No Cables used for connection Connecting to Computer Digital and Analog RGBConnecting to Video Equipment Digital and Video Connecting to Video Equipment Component and RGB Scart Basic Operation Wireless Remote Control OperationOperating the Projector Mouse OperationTop Control Remote Control Basic Operation and Reference ButtonsPad What is PIN code? Turning On the ProjectorEnter a PJ PIN code Turning Off the Projector Remote Control Zoom and Focus AdjustmentShutter Function Top ControlAuto PC Adjustment Input SelectionInformation Timer Function Keystone AdjustmentScreen Selection Picture Freeze FunctionZoom +/- Function Zoom +Zoom Remote Control Operation How to Operate On-Screen MenuTop Control Operation Mouse OperationControl bar for Mouse Operation Menu icon GuideMouse cursor Item dataMenu icons What You Can Do with Each Menu Menu Icons and Their FeaturesInput InputRGB Scart When video input signal is connected to When the input source is analog comingWhen the input source is component Move a pointer to Input 2 and press the Select buttonSystem SystemPC System Selection AutoComponent Signal Selection Video or S-Video Signal SelectionAV System Menu Video or S-Video AV System Menu ComponentPC Adjustment Computer AdjustmentAuto PC Adjust Auto PC adjManual PC Adjust Reset Sync phasePosition ModeImage Image AdjustmentFor PC Input For AV InputImage Adjust Color temp Auto picture controlRed GreenNoise reduction GammaProgressive FilmScreen Setting Screen SettingScreen Keystone ZoomCeiling RearSetting SettingLanguage MenuEnter a Logo PIN code LogoLamp BackgroundPower management Power managementDisplay Input searchAnalog out Lens memoryShutter Security Shutter ManagementKey lock USB lockTo Change PJ PIN Code To Change the PJ PIN Code settingExits the Setting menu Factory defaultSpecial SpecialFan control FilterTest pattern RS-232CUSB memory Information Exits Warning log menuMaintenance and Cleaning All indicators except the Lamp indicator are blinkingThen check the matters below Filter cover Air filter Air Filter ReplacementLamp Replacement Reset the Lamp timeLamp Lamp Handling Precautions Cleaning the Projection Lens Cleaning the Projector CabinetAttaching the Cord Cover Strap Main Indicators Indicators and Projector ConditionProjector is OFF. The AC power cord is unplugged May cause electric shock or a fire hazardAir filter is clogged with dust or has been used overtime Shutter IndicatorLamp Replace Indicators Lamp 1/2Until cooling is completed Appendix TroubleshootingLens position moves when Input Wireless Remote ControlIs switched Some displays are not seenFreq Compatible Computer Specifications1080i/50 1080i/60Technical Specifications Optional Parts AccessoriesMenu Tree PIN code change Information Dimensions USB Connector Series B Terminal ConfigurationsPIN Code Number Memo PIN Code Lock NoLogo PIN Code Lock No Numerics IndexAppendix Part No 327 9398 1AA6P1P5077-- KH6A