Sanyo PLC-ZM5000L owner manual Picture in Picture, Position Menu

Page 55

Setting

Picture in Picture

This function is used to project two images simultaneously by placing a separate small sub screen within or next to the main screen.

Use the Point ▲▼ buttons to select Picture in Picture and then press the SELECT button to display a dialog box. You can also display the dialog box by pressing and holding the PIP button on the remote control for more than 3 seconds. Only the sound from the source of Main picture is valid, while the source of Sub picture cannot output the sound. ( In P in P, the larger picture is main picture, and the smaller one is sub picture; in P by P, the left picture is main picture, and the right one is sub picture.)

User setting

Show the selected mode (Off/User 1-5) and its status (Stored /Free/ Adj..). User 1 and User 2 have stored default values. See page 30 for details.

P in P/P by P

P in P: Provide the images of Main picture and Sub picture at the ratio of Screen aspect in the Screen Menu.

P by P: Provide the images of Main picture and Sub picture at the ratio of 4:3.

Main picture / Sub picture

Input……Select an input from Input 1-3.

SourceSelect an input source. The display varies depending on the selected input.

Size……… Select the display size. Main picture can be

changed between 10 and 100%, and Sub picture can be changed between 10 to 50% in increments of 10%. When P by P is selected in Mode, the projection size is fixed to 50%.

PositionPress the SELECT button at Position and the display position setting screen appears.

Use the Point ▲▼◄► buttons to adjust the display position of active frame indicated in white. The frame will disappear after 10 seconds or when the SELECT button is pressed.

Selecting the Main picture or Sub picture

During Picture in Picture mode, and being undisplayed On Screen Menu, press the SELECT button to select Main or Sub picture. (A red frame will be displayed on the selected picture.)

Switching Input and Source

When selecting Main picture or Sub picture, input and source can be set by pressing the INPUT button on the side control or INPUT 1/2/3 button on the remote control. Operation on the On Screen Menu is not necessary.

Picture in Picture

Status (Stored /

 

Selected

Free/ Adj..) of the

Mode

selected mode.

 

Note:

P by P is not available when the 4:3 function is selected in Screen aspect (pp.44, 50).

When P by P is selected in every User 1-5 and the 4:3 function is selected

in Screen aspect, PIP button on the remote control is not available. To set

Picture in Picture, select Default (16:10) or 16:9 in Screen aspect (pp.44, 50).

When PIP is selected, screen is not available.

Position Menu

Active frame (White)

Center line

display

Note:

The Picture in Picture function is not available depending on the input signals and the selected input terminals. Refer to List of Picture in Picture for details. (p.89)

When the input signal(s) is/are incompatible, X mark will be displayed for 10 seconds on the Main/Sub picture.

55

Image 55
Contents Network Set-up and Operation  Projection lens is optionalFeatures and Design Table of Contents Please, help us to conserve the environ- ment we live Safety PrecautionTo The Owner For EU UsersMounting kit approved by the manufacturers Safety InstructionsFilter Safety Instructions Air CirculationIndicator Top PanelCautious use of equipment with laser technology Positioning PrecautionsSafety Instructions Moving the Projector Compliance AC Power Cord RequirementAC Power Cord for the United States and Canada AC Power Cord for the United KingdomBack ⑩ ⑪ ⑫ ⑱ Adjustable FeetPart Names and Functions FrontPart Names and Functions Rear Terminal Side Control Indicators on the top panel Part Names and Functions Side Control and IndicatorsPart Names and Functions Remote Control Part Names and Functions 16.4’ 5 m Remote Control Receivers and Operating RangeWired Remote Control Transmitter 16.4’Adjustable Feet Part Names and Functions Remote Control CodeON/OFF When the lens is shifted to top InstallationLens Shift Adjustment Lens shift adjustable rangeRemoving the lens Installation Lens InstallationAttaching the lens to the projector Unplug the power cords of both Analog Out Signal Table Before connecting cables Installation Connecting for Audio SignalProjector side AC Outlet side Installation Connecting the AC Power CordFor Continental Europe Turning On the Projector Basic OperationEnter a PIN code Basic Operation What is PIN code?When using the Direct OFF function, you can not Power off? disappears after 4 secondsOn-Screen Menu Basic Operation How to Operate the On-Screen MenuRemote Control Side ControlBasic Operation Main Menu Basic Operation Operating with Projector Control Zoom AdjustmentFocus Adjustment Lens Shift AdjustmentMenu Operation Basic Operation Sound AdjustmentVolume Dialog Box Direct OperationInformation Menu Basic Operation Operating with Remote ControlMouse Pointer button Timer buttonUser 1 of PIP example User 2 of PIP examplePoint Basic Operation Keystone CorrectionStandard Corner correctionArrow Finger Wireless Mouse OperationBasic Operation Pointer Function Mouse Pointer buttonDirect Operation Side Control/Remote Control OperationRemote Control Remote Control OperationRgbpc analog When Selecting Input 2 5 BNC Input JacksInput Selection Computer Input Source Selection Press the Menu button to display the On-ScreenRgbav Hdcp When Selecting Input 1 Computer Input TerminalsWhen Selecting Input 3 AV Terminals Input Selection Video Input Source SelectionSelecting Computer System Manually Computer InputComputer System Selection Automatic Multi-Scan SystemTo store the adjusted parameters Computer Input Auto PC AdjustmentPC adjust Menu Computer Input Manual PC Adjustment Computer Input Mode freeStore Image select Menu Computer Input Image Level SelectionImage adjust Menu Computer Input Image AdjustmentScreen Size Adjustment Digital zoom Custom adjCustom adj Digital zoom +Keystone Ceiling Rear Pb/Cb, Pr/Cr Jacks Video InputVideo System Selection Video Jack or S-video JackCinema Video Input Image Level SelectionImage select Menu NaturalTint Video Input Image AdjustmentSelected Image mode ColorVideo Input ……………When set to On, the aspect ratio is Video Input Screen Size AdjustmentNatural Wide Keystone Ceiling Setting SettingSetting Menu Language Position Logo select Capture Capture Logo PIN code lockLogo PIN code lock Enter a Logo PIN code Change the Logo PIN code lock settingChange the Logo PIN code lock setting Enter a Logo PIN codePosition Menu Picture in PictureSound To store the adjusted dataHdmi setup ImageLamp life control Lamp replacement iconLamp life control Lamp controlFilter control To change the code for the remote controlSimple mode buttons To change the code for the projectorRC sensor Power managementStandby mode Factory default is NetworkPointer TimerStop or Cancel the P-timer via Remote Control Direct on…Unlocked Key lockPIN code lock Security Key lock and PIN code lockPIN code change Change the PIN code lock settingEnter a PIN code Release key ShutterShutter ProtectionLow ... Keystone can not be selected Video delay controlClosed caption From Color to WhiteTest pattern Factory defaultFilter counter Filter counterDo not use the filter cartridge with other projector Maintenance and CareReset the Filter counter p.68 and the Scroll counter p.68 Filter InstructionsFilter cover Latch Tab Filter cartridge Maintenance and Care Replacing the Filter CartridgeOrder Replacement Filter Cartridge RecommendationScroll counter Reset? appears Maintenance and Care Resetting the Filter CounterResetting the Scroll Counter Filter counter Filter counter Reset? appearsFollow these steps to replace the lamp Maintenance and Care Lamp ReplacementLamp replacement icon Lamp Replace indicatorPOA-LMP136 Maintenance and CareLamp Handling Precautions Order Replacement LampCleaning the Projector Cabinet Maintenance and Care Cleaning the Projection LensUnplug the AC power cord before cleaning Then check the matters below Is the filter clean? Replace the filter with a new oneProblem Solutions TroubleshootingAppendix Appendix You cannot operate Wireless mouseIndicators blink or Shutter does notComputer Input/HDMI Input/Video Input Appendix Menu TreeComputer Input Screen Menu display varies depending on Input signalHdmi Input/Video Input Video InputSetting Language Projector is operating normally Appendix Indicators and Projector ConditionLamp Replace Projector is detecting abnormal conditionFreeze p.30 Projector ConditionAppendix Compatible Computer Specifications Freq..Hz Mechanical Information Appendix Technical SpecificationsPOA-CA-SCART Lens ReplacementAppendix Optional Parts PJ Link NoticeDigital DVI-D DVI 24 PIN Appendix Configurations of TerminalsLAN Terminal Appendix PIN Code Number Memo Appendix Dimensions Note Appendix List of Picture in PictureSerial Control Interface OperationFormat Functional Execution CommandStatus Read Command KH2AL
Related manuals
Manual 2 pages 48.98 Kb

PLC-ZM5000, PLC-ZM5000L specifications

The Sanyo PLC-ZM5000L and PLC-ZM5000 projectors are advanced models designed primarily for professional settings, including corporate presentations, educational environments, and high-end home theater setups. Both models are equipped with cutting-edge technologies that deliver exceptional image quality, brightness, and versatility.

One of the standout features of the Sanyo PLC-ZM5000L and PLC-ZM5000 is their high brightness output. With a luminosity rated at up to 5000 ANSI lumens, these projectors ensure clear and vibrant images even in well-lit rooms. This makes them ideal for large venues or spaces where ambient light poses a challenge. The projectors also utilize a high-resolution LCD panel that enhances color reproduction and sharpness, providing users with stunning visuals.

Another significant characteristic of these projectors is their flexible installation options. They feature a wide zoom range and extensive lens shift capabilities, which allow users to position the projector almost anywhere in the room without compromising image quality. This flexibility makes it easier to integrate the projectors into various environments, from conference rooms to auditoriums.

The PLC-ZM5000L and PLC-ZM5000 also incorporate advanced connectivity options. With multiple inputs available, including HDMI, VGA, and component video, users have the versatility to connect a variety of devices, from laptops and desktop computers to DVD players and Blu-ray systems. Additionally, some models support wireless connectivity, making it convenient to project content from personal devices without the clutter of wires.

These projectors also prioritize ease of use and maintenance. They come equipped with features such as an automatic vertical keystone correction, which helps adjust the image shape when the projector is not perfectly aligned with the screen. This ensures that presentations are professional-looking and free from distortion.

Furthermore, the Sanyo PLC-ZM5000L and PLC-ZM5000 boast a long lifespan for their lamp, reducing the frequency of replacements and minimizing downtime. The projectors are designed with energy-saving technologies that extend lamp life, contributing to lower operational costs.

Overall, the Sanyo PLC-ZM5000L and PLC-ZM5000 projectors stand out in the market for their high brightness, image quality, versatile installation options, comprehensive connectivity, and user-friendly features. These projectors are well-suited for professionals seeking reliable and high-performance solutions for their visual presentation needs.