Sanyo PLC-ZM5000L Shutter does not, You cannot operate, Does not work, Wireless mouse, Light

Page 75

Appendix

The shutter does not

– Check "Protection" or "Release key" of the Shutter function. (See p.63)

work..

 

Power management function runs by initial setting. Check “Setting” section on page 59.

When the filter cartridge replacement icon keeps appearing on the screen at turning on the projector for some time and no action is taken to replace

The power is turned off

the filter cartridge, the projector will be automatically shut down in 3

automatically..

minutes after turning on to protect the projector. (See pages 66, 81)

Do not cover the ventilation slots on the projector. (See pages 4, 6)

Projector may be used in high ambient temperature environment. Make sure the temperature is not out of Operating Temperature (41˚F–104˚F [5˚C–40˚C]). (See page 72)

You cannot operate

– If the side control is locked at "Key lock" under "Security" of Setting menu,

the side control is not available. Please check “Setting” section on page

with the side control..

61.

 

 

– Check the batteries.

 

– Check if the RC sensor is set properly. (See page 59)

 

– Make sure no obstruction is between the projector and remote control.

 

– Make sure you are not too far from the projector when using the remote

 

control.Maximum operating range is 16.4’ (5m). (See page 15)

The Remote Control

– Make sure that the remote control code conforms to the projector’s code.

(See “SETTING” section on page 58.)

does not work..

– Unlock the Key lock function for the remote control. (See page 61)

 

 

– Wireless remote control does not work when the remote control cable is

 

connected to the projector. (See page 15)

 

– Check if the ON/OFF switch on the remote control is set to “ON.”

 

– Make sure that the simple mode in the remote control function is set to Off

 

(See page 58).

Wireless mouse

– Check the cable connection between the projector and your computer.

(See pages 19, 32)

function does not

– Check the mouse setting on your computer.

work..

– Turn on the projector before you turn on the computer.

 

Indicators blink or

– Check the status of the projector with referring to “Indicators and projector

light..

condition” on pages 79-81.

appears on the screen

– Your operation is invalid. Operate correctly.

 

Unable to unlock the

 

Logo PIN code lock,

– Contact the dealer where you've purchased the projector or the service

Security key lock or

center.

Security PIN code lock..

 

Forget the Logo PIN

– Contact the dealer where you've purchased the projector or the service

code or Security PIN

center.

code..

 

 

– The projector detects an abnormal condition. Unplug the AC power cord and

appears on the screen

contact the dealer where you purchased the projector or the service center.

 

WARNING:

High voltages are used to operate this projector.. Do not attempt to open the cabinet..

If problems still persist after following all operating instructions, contact the dealer where you purchased the projector or the service center. Specify the model number and explain about the problem. We will advise you how to obtain service.

75

Image 75
Contents Network Set-up and Operation  Projection lens is optionalFeatures and Design Table of Contents Please, help us to conserve the environ- ment we live Safety PrecautionTo The Owner For EU UsersMounting kit approved by the manufacturers Safety InstructionsFilter Safety Instructions Air CirculationIndicator Top PanelCautious use of equipment with laser technology Positioning PrecautionsSafety Instructions Moving the Projector Compliance AC Power Cord RequirementAC Power Cord for the United States and Canada AC Power Cord for the United KingdomBack ⑩ ⑪ ⑫ ⑱ Adjustable FeetPart Names and Functions FrontPart Names and Functions Rear Terminal Side Control Indicators on the top panel Part Names and Functions Side Control and IndicatorsPart Names and Functions Remote Control Part Names and Functions 16.4’ 5 m Remote Control Receivers and Operating RangeWired Remote Control Transmitter 16.4’Part Names and Functions Remote Control Code Adjustable FeetON/OFF When the lens is shifted to top InstallationLens Shift Adjustment Lens shift adjustable rangeInstallation Lens Installation Removing the lensAttaching the lens to the projector Unplug the power cords of both Analog Out Signal Table Before connecting cables Installation Connecting for Audio SignalInstallation Connecting the AC Power Cord Projector side AC Outlet sideFor Continental Europe Basic Operation Turning On the ProjectorEnter a PIN code Basic Operation What is PIN code?When using the Direct OFF function, you can not Power off? disappears after 4 secondsOn-Screen Menu Basic Operation How to Operate the On-Screen MenuRemote Control Side ControlBasic Operation Main Menu Basic Operation Operating with Projector Control Zoom AdjustmentFocus Adjustment Lens Shift AdjustmentMenu Operation Basic Operation Sound AdjustmentVolume Dialog Box Direct OperationInformation Menu Basic Operation Operating with Remote ControlMouse Pointer button Timer buttonUser 1 of PIP example User 2 of PIP examplePoint Basic Operation Keystone CorrectionStandard Corner correctionArrow Finger Wireless Mouse OperationBasic Operation Pointer Function Mouse Pointer buttonDirect Operation Side Control/Remote Control OperationRemote Control Remote Control OperationRgbpc analog When Selecting Input 2 5 BNC Input JacksInput Selection Computer Input Source Selection Press the Menu button to display the On-ScreenRgbav Hdcp When Selecting Input 1 Computer Input TerminalsWhen Selecting Input 3 AV Terminals Input Selection Video Input Source SelectionSelecting Computer System Manually Computer InputComputer System Selection Automatic Multi-Scan SystemComputer Input Auto PC Adjustment To store the adjusted parametersPC adjust Menu Computer Input Manual PC Adjustment Mode free Computer InputStore Image select Menu Computer Input Image Level SelectionImage adjust Menu Computer Input Image AdjustmentScreen Size Adjustment Digital zoom Custom adjCustom adj Digital zoom +Keystone Ceiling Rear Pb/Cb, Pr/Cr Jacks Video InputVideo System Selection Video Jack or S-video JackCinema Video Input Image Level SelectionImage select Menu NaturalTint Video Input Image AdjustmentSelected Image mode ColorVideo Input Video Input Screen Size Adjustment ……………When set to On, the aspect ratio isNatural Wide Keystone Ceiling Setting SettingSetting Menu Language Position Logo select Capture Logo PIN code lock CaptureLogo PIN code lock Enter a Logo PIN code Change the Logo PIN code lock settingChange the Logo PIN code lock setting Enter a Logo PIN codePosition Menu Picture in PictureSound To store the adjusted dataHdmi setup ImageLamp life control Lamp replacement iconLamp life control Lamp controlFilter control To change the code for the remote controlSimple mode buttons To change the code for the projectorRC sensor Power managementStandby mode Factory default is NetworkPointer TimerStop or Cancel the P-timer via Remote Control Direct on…Unlocked Key lockPIN code lock Security Key lock and PIN code lockChange the PIN code lock setting PIN code changeEnter a PIN code Release key ShutterShutter ProtectionLow ... Keystone can not be selected Video delay controlClosed caption From Color to WhiteTest pattern Factory defaultFilter counter Filter counterDo not use the filter cartridge with other projector Maintenance and CareReset the Filter counter p.68 and the Scroll counter p.68 Filter InstructionsFilter cover Latch Tab Filter cartridge Maintenance and Care Replacing the Filter CartridgeOrder Replacement Filter Cartridge RecommendationScroll counter Reset? appears Maintenance and Care Resetting the Filter CounterResetting the Scroll Counter Filter counter Filter counter Reset? appearsFollow these steps to replace the lamp Maintenance and Care Lamp ReplacementLamp replacement icon Lamp Replace indicatorPOA-LMP136 Maintenance and CareLamp Handling Precautions Order Replacement LampMaintenance and Care Cleaning the Projection Lens Cleaning the Projector CabinetUnplug the AC power cord before cleaning Then check the matters below Is the filter clean? Replace the filter with a new oneTroubleshooting Problem SolutionsAppendix Appendix You cannot operate Wireless mouseIndicators blink or Shutter does notAppendix Menu Tree Computer Input/HDMI Input/Video InputComputer Input Screen Menu display varies depending on Input signalHdmi Input/Video Input Video InputSetting Language Projector is operating normally Appendix Indicators and Projector ConditionLamp Replace Projector is detecting abnormal conditionFreeze p.30 Projector ConditionAppendix Compatible Computer Specifications Freq..Hz Mechanical Information Appendix Technical SpecificationsPOA-CA-SCART Lens ReplacementAppendix Optional Parts PJ Link NoticeAppendix Configurations of Terminals Digital DVI-D DVI 24 PINLAN Terminal Appendix PIN Code Number Memo Appendix Dimensions Note Appendix List of Picture in PictureSerial Control Interface OperationFormat Functional Execution CommandStatus Read Command KH2AL
Related manuals
Manual 2 pages 48.98 Kb

PLC-ZM5000, PLC-ZM5000L specifications

The Sanyo PLC-ZM5000L and PLC-ZM5000 projectors are advanced models designed primarily for professional settings, including corporate presentations, educational environments, and high-end home theater setups. Both models are equipped with cutting-edge technologies that deliver exceptional image quality, brightness, and versatility.

One of the standout features of the Sanyo PLC-ZM5000L and PLC-ZM5000 is their high brightness output. With a luminosity rated at up to 5000 ANSI lumens, these projectors ensure clear and vibrant images even in well-lit rooms. This makes them ideal for large venues or spaces where ambient light poses a challenge. The projectors also utilize a high-resolution LCD panel that enhances color reproduction and sharpness, providing users with stunning visuals.

Another significant characteristic of these projectors is their flexible installation options. They feature a wide zoom range and extensive lens shift capabilities, which allow users to position the projector almost anywhere in the room without compromising image quality. This flexibility makes it easier to integrate the projectors into various environments, from conference rooms to auditoriums.

The PLC-ZM5000L and PLC-ZM5000 also incorporate advanced connectivity options. With multiple inputs available, including HDMI, VGA, and component video, users have the versatility to connect a variety of devices, from laptops and desktop computers to DVD players and Blu-ray systems. Additionally, some models support wireless connectivity, making it convenient to project content from personal devices without the clutter of wires.

These projectors also prioritize ease of use and maintenance. They come equipped with features such as an automatic vertical keystone correction, which helps adjust the image shape when the projector is not perfectly aligned with the screen. This ensures that presentations are professional-looking and free from distortion.

Furthermore, the Sanyo PLC-ZM5000L and PLC-ZM5000 boast a long lifespan for their lamp, reducing the frequency of replacements and minimizing downtime. The projectors are designed with energy-saving technologies that extend lamp life, contributing to lower operational costs.

Overall, the Sanyo PLC-ZM5000L and PLC-ZM5000 projectors stand out in the market for their high brightness, image quality, versatile installation options, comprehensive connectivity, and user-friendly features. These projectors are well-suited for professionals seeking reliable and high-performance solutions for their visual presentation needs.