Sanyo POA-LN02 owner manual Connection of LAN cable

Page 20

20

Chapter 2 Installation

Connection of LAN cable

To connect to the network, it is required to use the UTP (Unshielded Twisted Pair) straight cable with RJ-45 plug. There are two different types of cables depending on whether the network is constructed with 10Base-T or 100Base-TX. Prepare the Hub (10Base-T or 100Base-TX) to distrib- ute the network cable if required.

1 Disconnect the AC plug from the monitor.

2 Connect the UTP straight cable to the LAN port on the network unit.

3 Connect the UTP straight cable to the hub.

Hub

(10Base-T, 100Base-TX)

Monitor

UTP straight cable

The AC cord must be disconnected from AC power outlet when connecting the cable. It may damage the product.

When you set up the network which has a default setting by using computer, it must be carried out in the network which does not connect to other monitors.

Use the UTP cross cable when you connect the computer and monitor directly not using the hub.

When you connect the monitor into the 10Base-T network, use cable with category 3 or 5. When you connect the monitor into the 100Base-TX network, use cable with category 5.

The length of cable between hub and monitor should be less than 100m.

Image 20

Contents POA-LN02 LD-Net OrganizerCompliance Federal Communication Commission NoticeModel Numbers POA-LN02 Trade Name Sanyo Responsible party AddressCompliance and Caution Contents Network Viewer AppendixPage Chapter Features Web Management function p.45 Multi-control function p.59 Operating environment of LD-Net Organizer Quick Setup Guide Before usePackage contains Network unitTrademarks Expression/AbbreviationUse of this manual Preparation Installation Flow of installation Installation and network configuration p.18-25Installation of the software p.26-28 Set up is completeName and function of each part Installation and network configuration MountingInstallation and network configuration Connection of LAN cable Configure the network with computer Network configurationProcedure of Connecting the monitor to the network As follows and restart the computer Configure the network with the computerDefault network configuration is set as follows Completing of installation Configure the network of computer Network PIN code setting Set the supplied Network Viewer & Capture Installing the softwareNetwork Viewer & Capture 3 installation Installed software Following 3 software are installed on your computerNetwork Capture Network Viewer 3 File ConverterFile Converter 2 Installation Installed software and placesBasic Setting and Operation Login the setting page of the monitor Select a display mode and loginEnter the IP address Entering User Name must be user and it can not be changedDisplay of main setting Main setting page in the Standard Mode displayHow to use the setting Main setting page in the Light Mode displayExample of the Setting Set buttonType of the setting pallet Text box settingPull-down menu setting Radio button settingDescription Initial settingUse of Battery Initial setting Manual setting Date and time settingAuto setting Network configuration Sets IP address of the monitorMail setting Setting Smtp server and administrator addressIs turned off except Power/Fan fail, High Temp, Power save Registering and deleting E-mail addressesOption selection for sending alert mail Addresses are listed as the figure on the rightExamples Type and contents of alert mail When the signal is interrupted When panel usage time reaches hoursWhen power save function turns Monitor off Snmp setting Enter user name of the monitor etc. optionalEnter place of the monitor optional CommunityCheck and delete the trap address TrapItem Description Up to 10 trap addresses can be registeredTrap option setting Trap optionControlling the Monitor Power control and status check Description Monitor statusPower control and status check Selects input mode of the monitor Selects signal source of the inputControls InputPicture adjustment This function is to adjust the displayed picture imageSuppresses the sound. ON, OFF Adjusts the sound volumeSound PC adjustment Setting up the monitor Switches the screen mode. Full, Zoom169There may not be available mode depending on Input modeSets remote control inhibition mode. ON, OFF This function is not effective for the settingsMail settings, etc Sets the image to freeze mode.ON, OFFSets tile mode active. Off, On Adjusts the vertical picture for smooth imageSets to divide the horizontal picture Sets to divide the vertical pictureSet a day or date Timer settingHow to set the timer Check the timer events Change the event modeSet an execute time Select an event actionTime Monitor information Items DescriptionExample of multi control Controlling and setting the multi-monitorsMulti-control Multi control setting Start/stop the multi controlRegister the monitor Confirmation of registered monitorChange the mode of the registered monitor Mode OperationStatus IndicationsControlling all together Check & Change page in the light modeSetting all together Viewer auto setting all together Network Capture Commands on the task bar About Network Capture functionLaunching the Network Capture Real Time Capture p.68About Image Quality Parameter set upClick Network Capture 3 icon on the task bar Up to 30 computers can be registered Using the Real Time CaptureRegistering the computers Select input mode to Network previously Control by the computerControl by the web browser Start capturing of the PC1 from the PC5Using the Network Communication Settings before using the Network Communication Description of capture editing window Menu treeCommand Tool Save Command ToolTool bar button names Bar of Sub PCHow to use the Network Communication Setting of the drawing tool attribute Edit capture imageDrawing figures Erase drawn objectLetter attribute setting Drawing letterOn the Communication Network Communication operation and change of statePreparation Quits the communication forcibly Executing the forcing modeReleases the editing authority forcibly Error messages Network Viewer How to use the Network Viewer 3 File Converter Creating the available data Network ViewerLaunch and quit the File Converter File Converter 1 windowUpdate Updates contents of the preview window Create the available dataMenu Tree Menu Sub Menu DescriptionNetwork Viewer Setting of output destination and conversion mode Conversion modeOutput destination FolderOpen a document with the individual software Select a folder and click Save buttonProcedure of making program Creating a program file Program EditorEnter the FTP server name or IP address Specify the root directory of the FTP server. Normally useDisplays the folder selection window Deletes the folder path from the folder listMoves up the selected folder path Moves down the selected folder pathSetting up the display order and time of the images Image frame on the index window Blue frameRed frame Shows that the image in the folder is unchangedLimitation of the Program file This function is not available in the light modeExample of the created program selection Condition to use the Network Viewer function Using the Network Viewer functionUsed when using the network capture function Setup the setting page 1 of Image display setting Setup the setting page 2 of Selection display settingSwitches to the List mode Switches to the thumbnail modeSteps down the startup image Auto display functionAuto Display setting and control Error information Error type DescriptionAppendix To another network Examples of connectionPeer-To-Peer connection Gateway Router installed in the network Entrance hallWeb browser setting Active Script/JavaScript enableFlash Player enable Proxy settingActiveX controls and plug-ins setting Examples OS/BrowsersWindows XP Professional 101Flash Player Add-on setting Using proxy serverNot using proxy server 102103 Netscape Navigator104 Product specification 105106 Port specificationPin modular connector RJ-45 Following causes are possible. Please check them Why doesn’t the setting page appear in my web browser?107 How can I restrict access from the computer 108109 How many monitors can I control with multi-control function?110 You can register up to 10 addressesWhy am I not receiving E-mail alert messages? 111Can I update the firmware of the network unit 112What is the MAC address assigned to the network unit? 113What are the rules for IP address assignment? MAC address is indicated on the case back as the belowWhy doesn’t the computer screen appear on the monitor? 114Images from the file server don’t appear on the monitor? Cannot make a new program fileMicrosoft power point format .ppt 115What kind of image formats can I convert? Bitmap format .bmp Jpeg format .jpeg .jpgIfkm