Sanyo POA-LN02 owner manual Network configuration, Sets IP address of the monitor

Page 37

Network configuration

Network configuration

Click Network on the main menu. The following setting page is displayed. The IP Address, Subnet Mask, Default Gateway, DNS (Domain Name Server) and monitor name are set up on this Setting sub menu.

The IP address and Subnet Mask have been configured already in chapter "Installation". If you want to change them or configure default gateway or DNS, perform them in this page. If you change them, the network unit begins restarting and it takes about 20 sec- onds. Close (Quit) the web browser and access to the login page again in 20 seconds.

Item	Description

IP address	Sets IP address of the monitor
Subnet mask	Sets Subnet mask. Normally sets 255.255.255.0
Default gateway*1	Sets IP address of the default gateway (Router)
DNS*2	Sets IP address of the DNS server. Must be set
Monitor name*3	when using the e-mail function
Monitor name*3	Sets name of the monitor. (64 characters maxi-
	mum)

You must use the number specified by your administrator. The address must be entered as a group with four numbers split by a dot like [192.168.001.101].

*1 Set [0.0.0.0] if the network does not provide the gateway (router).

*2 Set [0.0.0.0] if you do not use the function E-mail alert.

*3 If you use the DNS server, register the host name registered to the DNS server as a monitor name.

You can access with this monitor name from any computers in your network. If you do not use the DNS server, access with the assigned IP address to the monitor.

* All the network setting will reset to the default when setting [0.0.0.0] of the IP Address.

LD-NET ORGANIZER

OWNER'S MANUAL

37

Image 37

Contents LD-Net Organizer POA-LN02Federal Communication Commission Notice ComplianceModel Numbers POA-LN02 Trade Name Sanyo Responsible party AddressCompliance and Caution Contents Appendix Network ViewerPage Chapter Features Web Management function p.45 Multi-control function p.59 Operating environment of LD-Net Organizer Before use Quick Setup GuidePackage contains Network unitUse of this manual Expression/AbbreviationTrademarks Preparation Installation Installation and network configuration p.18-25 Flow of installationInstallation of the software p.26-28 Set up is completeName and function of each part Mounting Installation and network configurationInstallation and network configuration Connection of LAN cable Procedure of Connecting the monitor to the network Network configurationConfigure the network with computer Default network configuration is set as follows Configure the network with the computerAs follows and restart the computer Completing of installation Configure the network of computer Network PIN code setting Network Viewer & Capture 3 installation Installing the softwareSet the supplied Network Viewer & Capture Following 3 software are installed on your computer Installed softwareNetwork Capture Network Viewer 3 File ConverterInstalled software and places File Converter 2 InstallationBasic Setting and Operation Select a display mode and login Login the setting page of the monitorEnter the IP address Entering User Name must be user and it can not be changedMain setting page in the Standard Mode display Display of main settingMain setting page in the Light Mode display How to use the settingExample of the Setting Set buttonText box setting Type of the setting palletPull-down menu setting Radio button settingUse of Battery Initial settingDescription Initial setting Auto setting Date and time settingManual setting Sets IP address of the monitor Network configurationSetting Smtp server and administrator address Mail settingRegistering and deleting E-mail addresses Is turned off except Power/Fan fail, High Temp, Power saveOption selection for sending alert mail Addresses are listed as the figure on the rightExamples Type and contents of alert mail When power save function turns Monitor off When panel usage time reaches hoursWhen the signal is interrupted Enter user name of the monitor etc. optional Snmp settingEnter place of the monitor optional CommunityTrap Check and delete the trap addressItem Description Up to 10 trap addresses can be registeredTrap option Trap option settingControlling the Monitor Description Monitor status Power control and status checkPower control and status check Selects signal source of the input Selects input mode of the monitorControls InputThis function is to adjust the displayed picture image Picture adjustmentSound Adjusts the sound volumeSuppresses the sound. ON, OFF PC adjustment Switches the screen mode. Full, Zoom169 Setting up the monitorThere may not be available mode depending on Input modeThis function is not effective for the settings Sets remote control inhibition mode. ON, OFFMail settings, etc Sets the image to freeze mode.ON, OFFAdjusts the vertical picture for smooth image Sets tile mode active. Off, OnSets to divide the horizontal picture Sets to divide the vertical pictureHow to set the timer Timer settingSet a day or date Change the event mode Check the timer eventsSet an execute time Select an event actionTime Items Description Monitor informationMulti-control Controlling and setting the multi-monitorsExample of multi control Start/stop the multi control Multi control settingConfirmation of registered monitor Register the monitorMode Operation Change the mode of the registered monitorStatus IndicationsSetting all together Check & Change page in the light modeControlling all together Viewer auto setting all together Network Capture About Network Capture function Commands on the task barLaunching the Network Capture Real Time Capture p.68Click Network Capture 3 icon on the task bar Parameter set upAbout Image Quality Registering the computers Using the Real Time CaptureUp to 30 computers can be registered Control by the computer Select input mode to Network previouslyStart capturing of the PC1 from the PC5 Control by the web browserUsing the Network Communication Settings before using the Network Communication Menu tree Description of capture editing windowCommand Tool Command Tool SaveTool bar button names Bar of Sub PCHow to use the Network Communication Edit capture image Setting of the drawing tool attributeDrawing figures Erase drawn objectDrawing letter Letter attribute settingPreparation Network Communication operation and change of stateOn the Communication Releases the editing authority forcibly Executing the forcing modeQuits the communication forcibly Error messages Network Viewer Creating the available data Network Viewer How to use the Network Viewer 3 File ConverterLaunch and quit the File Converter File Converter 1 windowCreate the available data Update Updates contents of the preview windowMenu Tree Menu Sub Menu DescriptionNetwork Viewer Conversion mode Setting of output destination and conversion modeOutput destination FolderSelect a folder and click Save button Open a document with the individual softwareCreating a program file Program Editor Procedure of making programEnter the FTP server name or IP address Specify the root directory of the FTP server. Normally useDeletes the folder path from the folder list Displays the folder selection windowMoves up the selected folder path Moves down the selected folder pathSetting up the display order and time of the images Blue frame Image frame on the index windowRed frame Shows that the image in the folder is unchangedExample of the created program selection This function is not available in the light modeLimitation of the Program file Used when using the network capture function Using the Network Viewer functionCondition to use the Network Viewer function Setup the setting page 2 of Selection display setting Setup the setting page 1 of Image display settingSwitches to the thumbnail mode Switches to the List modeSteps down the startup image Auto display functionAuto Display setting and control Error type Description Error informationAppendix Peer-To-Peer connection Examples of connectionTo another network Entrance hall Gateway Router installed in the networkActive Script/JavaScript enable Web browser settingFlash Player enable Proxy settingExamples OS/Browsers ActiveX controls and plug-ins settingWindows XP Professional 101Using proxy server Flash Player Add-on settingNot using proxy server 102Netscape Navigator 103104 105 Product specificationPin modular connector RJ-45 Port specification106 107 Why doesn’t the setting page appear in my web browser?Following causes are possible. Please check them 108 How can I restrict access from the computerHow many monitors can I control with multi-control function? 109You can register up to 10 addresses 110111 Why am I not receiving E-mail alert messages?112 Can I update the firmware of the network unit113 What is the MAC address assigned to the network unit?What are the rules for IP address assignment? MAC address is indicated on the case back as the below114 Why doesn’t the computer screen appear on the monitor?Images from the file server don’t appear on the monitor? Cannot make a new program file115 Microsoft power point format .pptWhat kind of image formats can I convert? Bitmap format .bmp Jpeg format .jpeg .jpgIfkm