JBL CVR700, CVPD50 manual Making Configuration Adjustments, System Configuration

SYSTEM CONFIGURATION

NOTE: All remotely controlled compo- nents must be linked together in a “daisy chain.” Connect the IR OUT jack of one unit to the IR IN of the next to establish this chain.

You are now ready to power up the sys- tem, make minor configuration settings, and then begin enjoying your JBL Cinema Vision system.

1.Plug the AC power cords for the CVPD50, CVR700 and any source devices into unswitched AC outlets. Make sure the master power switch on the underside of the CVPD50 (next to the power cord jack) is in the “1” position. Use a small mirror to locate the switch. The LED inside the

Main Power On/Off Switch 1on the CVR700 will turn red, indicating that the unit is in Standby mode. The LED on the front of the CVPD50 will turn amber, indi- cating that it, too, is in Standby mode.

NOTE: It is possible to see the LED on the front panel of the CVPD50 flashing red and yellow alternately even though you have unplugged the CVPD50’s power cord. This is because the CVPD50 also receives power through its connection to the CVR700 in order to trigger turn-on when the CVR700 is powered on for seamless operation; this is normal. However, the CVPD50’s power cord must be plugged in for proper operation; the LED will flash when the CVR700 is turned on to alert you that the power cord is unplugged. If the CVPD50 does not turn on when the CVR700 is powered up and the LED on the CVPD50 is not flashing red and yellow, then turn off both units, unplug them both from AC power, unplug the JBL Digital Link cable that connects them and then reconnect everything. If this does not resyn- chronize the components, contact your authorized JBL custom installer or dealer for assistance.

2.Remove the protective plastic film from the front-panel lens. If left in place, the film will affect the performance of your remote control.

3.Install the four supplied AAA batteries in the main remote as shown in Figure 5. Be certain to follow the (+) and (–) polarity indicators that are on the top of the bat- tery compartment.

Figure 5

4.Press the Main Power On/Off Switch

1b 1 to turn on the CVR700 and the CVPD50.

5.The remote control contains several pre- programmed special functions that may be activated by pressing and holding par- ticular buttons rather than pressing and releasing. One such function is the “All On/Off” power function. To turn on the CVR700, CVPD50 display screen, and other devices programmed into the remote, press and hold the Power All On Button buntil all units turn on. The LED inside the CVR700’s Main Power On/Off Button 1will turn orange to confirm that the unit is on, and the Information Display Ôwill also light. The CVPD50 will turn on and display the JBL logo screen.

Using the On-Screen Display

When making the following adjustments, you may find it easier to use the on-screen display system. These easy-to-read displays give you a clear picture of the current status of the unit and make it easy to see which selection you are making. To view the on- screen menus, make certain that you have made a connection to the CVPD50 from the

Output to JBL Cinema Vision CVPD50

Screen Port 33 on the rear panel of the CVR700. The CVR700’s on-screen menus are not available when a component video source device is in use unless the corre- sponding S-video connection has been made to the CVR700. The on-screen menus are not available at all when the DVI

(HDCP)/Computer Video Input 35 is

in use. If you attempt to use the on-screen menus, the DVI video input will be tem- porarily lost.

IMPORTANT NOTES:

•In order to access the on-screen menus for the CVR700’s audio section, make sure the remote control is in System mode (NOT set to control an external source device or even the CVPD50 screen). To set the remote to System mode, press the

System Selector j 33 .

•Both the CVPD50 and CVR700 contain separate IR sensors that are capable of receiving commands from either remote control. JBL recommends that you point the remote at the CVPD50 screen for all commands, as the JBL Digital Link cable is able to pass remote commands to the CVR700 for system and DVD control, as well as to any other devices you have connected to the Remote IR Output Jack fi. However, video control com- mands received by the CVR700 cannot be passed to the screen.

•When viewing the on-screen menus, it is important that they not be left on the screen for an extended period of time. The constant display of a static image such as these menus or video game images is likely to cause the image to be permanently “burned into” the plasma screen. This type of damage is not covered by the JBL Cinema Vision warranty.

Making Configuration

Adjustments

The on-screen menu system for the audio section is available by pressing the OSD Button n 36 . When this button is pressed, the MAIN MENU (Figure 6) will appear, and adjustments are made from the individual menus. To use the on-screen menu system in the audio section of the CVR700, press the ⁄/¤ Navigation Controls q 4 until the on-screen› cursor is next to the item you wish to adjust, and then press the Set Button s 7 to select that item. In some cases, the selection will cause a new submenu to appear, and when the lowest level submenu has been reached, pressing the Set Button s 7 will select the item that the on-screen› cur- sor is pointing to. Some settings in the ADVANCED submenu will require you to press the. ‹/›Navigation Controls q 6 to scroll through the available settings. Throughout this manual, when you are asked to “scroll” to a certain item, that means to use the ⁄/¤ Navigation Controls q 4 until the on-screen› cursor is next to the item.

* * M A I N M E N U * *

›S Y S T E M C O N F I G U R A T I O N S O U R C E S

S P E A K E R S

A D V A N C E D

L I P S Y N C

Figure 6

The menus will remain on the screen for 20 seconds, and then they will “time-out” and disappear from the screen. The time- out may be increased to as much as 50 seconds by going to the ADVANCED SETTINGS menu, and changing the item titled OSD TIME OUT.

Selections will also be shown in the Upper Display Line Hor the Lower Display Line E, depending on which parameter is being adjusted. In general, the Upper Display Line Hwill indicate the name of the current menu and the Lower Display Line E, will indicate

45