JBL CVPD50, CVR700 manual Key, Renaming Individual Buttons, Characters

will move the cursor one more space to the right, leaving a blank space between the last letter and the next one.

8.Repeat Step 7 as needed to enter all the needed letters, numbers, charac- ters and spaces.

9.When the text entry is complete, press the Set Button s. The LCD display will blink DEVICE RENAMED three times and then return to normal operation.

Once a device is renamed you will see the new name on the top line of the remote’s LCD display whenever the Input//Device Selector 3is pressed, or when any other command/function button on the remote is pressed after the main Device Selector is pressed. Note that renaming a device in the remote will not change the name of the input used by the on-screen menu system of the CVR700.

NOTES ON RENAMING DEVICES:

•To move the cursor to the right or left of the display during the renaming process, press the ‹/› Navigation Buttons qas required.

•The table below shows the letters, numbers and characters that may be accessed by pressing the Numeric

Keys:
Key	Characters	Key	Characters
1	[,],/,1	6	M,N,O,6
2	A,B,C,2	7	P,Q,R,S,7
3	D,E,F,3	8	T,U,V,8
4	G,H,I,4	9	W,X,Y,Z,9
5	J,K,L,5	0	-,.,#,0

There is a limit of nine characters (includ- ing spaces) for any new device or button name.

•Renaming a device changes the name of the device only, not any of the indi- vidual key functions within that device memory. To change the name of an individual device, follow the instruc- tions in the next section.

Renaming Individual Buttons

Thanks to the programming flexibility of the CVR700R2 remote, an individual but- ton on the remote may be assigned a fea- ture or function that is different from the name that appears as the factory default when the button is pressed. With the Rename Button function, it is possible to rename almost any button on the remote so that when the button is pressed you will see a more descriptive or appropriate name displayed.

To rename a specific button on the remote, follow these steps. For instance, this example will show you how to pro- gram the remote so that FULL SCREEN appears in the remote’s LCD display when you press the Tone Button Hwhile in CABLE mode to match the original cable remote. Of course, remember that you will first have to learn the codes for that function into the Exit button, following the instructions shown on page 78.

1.Press and hold the Remote Menu Button bfor about 3 seconds while the message shown in Figure 54 appears in the remote’s LCD Information Display 2. Release the button when the red light under the Set Button sappears.

2.The remote’s MAIN MENU message (Figure 55), will appear in the LCD dis- play and the Set Button swill remain illuminated in red. Press the

⁄/¤ Navigation Button quntil

RENAME appears on the bottom line of the LCD screen, as shown in Figure 106.

3.At the next menu screen, press the

⁄/¤ Navigation Button quntil

RENAME BUTTON appears on the bottom line of the LCD screen, as shown in Figure 109. Press the Set Button sto continue.

R E N A M E

R E N A M E B U T T O N

Figure 109

4.The next display screen (Figure 110) is where you select the device within which the button to be renamed exists. Press the ⁄/¤ Navigation Buttons Quntil the name of the base device appears. In our example, since we want to rename a button within the DVD device memory, DVD/MAIN should appear in the lower line of the LCD. When the desired device name appears, press the Set Button S.

S E L E C T A D E V I C E

D V D / M A I N

Figure 110

5.At the next menu screen you will select the first button within the device to be renamed, as instructed in the display shown in Figure 111. Select the button (in this case, the

Exit/Cancel Button H) by simply pressing it on the remote.

P R E S S A B U T T O N

Figure 111

6.Depending on whether or not the but- ton pressed already has a named function within the device selected, one of two things will happen.

a.If the button to be renamed already has a pre-programmed, or previ- ously renamed title in the remote’s memory, you will see that name on the top line of the LCD display, and a blinking block cursor will appear on the far left side of the bottom line of the display, as shown in Figure 112.

b.If the button to be renamed does not have a function in the device selected, the top line of the LCD screen will be blank, and a blinking block cursor will appear on the far left side of the bottom line of the display.

E X I T

Figure 112

7.To enter the new name for the button, press the Alphanumeric Keys l. The letters above the numbered but- tons indicate which letters or symbols will appear when the button is pressed during the renaming process. The first press of the button will enter the first character shown, subsequent presses of the same button will change the display to the other let- ters above that numbered key. For example, since the first letter we need to rename the Exit button to Full screen is an “F,” you would locate the “F” above the “9” button, and press the button four times. The first press shows a “D,” and subsequent presses step through the other letters avail- able until the “F” appears. Consult the table at left to see which characters are available by pressing

aparticular button.

8.After you enter the first letter of the new device name, there are three options for entering the next character:

a.To enter a letter that requires a dif- ferent numeric key to be pressed, simply press that button. The cur- sor will automatically move to the next position and the first letter accessed by the new button will appear. Following our example, the

86