Sanyo PLC-WXE46 owner manual Installation, Positioning the Projector, Adjustable Feet

Page 13

Installation

Positioning the Projector

For the projector positioning, see the figures below.

The projector should be set perpendicularly to the plane of the screen.

Note:

•This projector is not equipped with an optical zoom. To adjust the screen size, change the throw distance. •The brightness in the room has a great influence on picture quality. It is recommended to limit the ambient lighting in order to get the best image.

•All measurements are approximate and may vary from the actual sizes.

3.927’ (119.7 cm)

(Inch Diagonal)

2.826’ (86.1 cm)

 

 

 

110”

 

 

 

 

 

 

1.726’ (52.6 cm)

 

 

 

 

80”

 

 

50”

A

Screen Size

50”

80”

110”

(W x H) mm

 

 

 

1077 x 673

1723 x 1077

2369 x 1481

16:10aspect ratio

 

 

 

 

Throw distance

1.726’ (52.6 cm)

2.826’ (86.1 cm)

3.927’(119.7 cm)

 

 

 

 

A

0.623’ (19.0 cm)

0.846’ (25.8 cm)

1.069’ (32.6 cm)

 

 

 

 

Adjustable Feet

Projection angle can be adjusted up to 10.0 degrees with the adjustable feet.

1

Lift the front of the projector and pull the feet lock latches

2

on both sides of the projector upward.

Release the feet lock latches to lock the adjustable feet

 

and rotate the adjustable feet to adjust the position and

 

tilt.

3

To retract the adjustable feet, lift the front of the projector

 

and pull and undo the feet lock latches.

Keystone distortion of the projected image can be corrected by remote control operation or menu operation (pp.22, 41).

Feet Lock Latches

Adjustable Feet

13

Image 13
Contents Network Supported Model PLC-WXE46Note Features and DesignTable of Contents To the Owner Safety PrecautionSafety Instructions Installing the Projector in Proper Position Safety Instructions Air CirculationMoving the Projector Compliance AC Power Cord RequirementFederal Communications Commission Notice ④ Exhaust Vents Part Names and Functions③ LAN Connection Terminal Part Names and Functions Rear TerminalPart Names and Functions Top Control Part Names and Functions Remote Control Operating Range Part Names and Functions Remote Control Battery InstallationAdjustable Feet InstallationPositioning the Projector Cables used for connection Installation Connecting to a ComputerAudio Video Installation Connecting to Video EquipmentInstallation Connecting to Component Video Equipment Projector side AC outlet side Installation Connecting the AC Power CordBasic Operation What is PIN code?Turning On the Projector Enter a PIN codeBasic Operation Turning Off the Projector Top Control Menu button Point buttons Basic Operation How to Operate the On-Screen MenuFor computer source Basic Operation Menu BarFor video source Remote Control Basic Operation Focus AdjustmentKeystone Correction Top ControlRemote Control Operation Basic Operation Sound AdjustmentCOMPUTER/VIDEO button Freeze buttonBasic Operation Input Source Selection Computer InputInput Menu Source Select MenuAuto Computer Input Computer System SelectionPC System Menu ModeDirect Operation Remote Control Computer Input Auto PC AdjustmentTo store the adjusted parameters PC Adjust MenuComputer Input Manual PC Adjustment Computer Input Computer Input Image Level Selection Computer Input Image Level Adjustment Normal Screen Size AdjustmentTrue FullFor zooming in and out the images Digital zoom + CustomDigital zoom Video Input Remote Control Menu OperationInput Source Selection Video, S-video Source Select Menu VideoPointer to Computer 1 and then press the Select Video or S-video Auto Video Input Video System SelectionComponent Auto AV System Menu Video or S-videoCinema Video Input Image Level SelectionColor Video Input Image Level AdjustmentTint Noise reduction Video InputProgressive Zoom Video Input Screen Size AdjustmentWide Natural wideSetting SettingLoo Loo and Loo PIN code lock settins SettinLoo select CaptureChange the Logo PIN code Enter a Logo PIN codeLogo PIN code lock Logo PIN code lock Logo PIN code lock Dialog BoxRear CeilingScreen aspect TerminalPower management Standby modeOn start Remote control To change the code for the remote controlOn start Lamp controlKey lock Security Key lock and PIN code lock settingsPIN code lock Change the PIN code Change the PIN code lock settingChange the PIN code Fan control FanLamp counter Filter counterClosed Caption Factory default Factory defaultWarnin lo Closed CaptionNote Then check the matters below Maintenance and CleaningResetting the Filter Counter Maintenance and Cleaning Cleaning the Air FiltersCleaning the Projection Lens Maintenance and Cleaning Attaching the Lens CoverCleaning the Projector Cabinet Reset the lamp replacement counter Maintenance and Cleaning Lamp ReplacementMaintenance and Cleaning Lamp Replacement Counter Lamp Handling PrecautionsAppendix TroubleshootingAppendix Projector Condition see Indicator blinks or lightsSound Appendix Menu TreeComputer Input/Video Input Computer InputSystem AutoSetting Video Input SettingProjector Condition Appendix Indicators and Projector ConditionDisplay Appendix Compatible Computer SpecificationsTechnical Specifications Accessories DimensionsOptional Parts Appendix PJ Link Notice Service Port Connector Terminal Mini DIN 8-PIN Appendix Configurations of TerminalsPIN Code Lock No Appendix PIN Code Number MemoLogo PIN Code Lock No KM5AY