Sanyo PLC-WXE46 owner manual Appendix Indicators and Projector Condition

Page 61

Appendix

Indicators and Projector Condition

Check the indicators for projector condition.

 

Indicators

 

Projector Condition

POWER

WARNING

LAMP

red/green

red

REPLACE

 

yellow

 

 

 

 

 

 

 

 

 

 

 

The projector is off. (The AC power cord is unplugged.)

 

 

 

 

 

 

 

The projector is preparing for stand-by or the projection lamp is

 

 

being cooled down. The projector cannot be turned on until cooling is

 

 

 

completed.

 

 

 

 

 

 

 

The projector is ready to be turned on with the POWER ON/STAND-BY

 

 

button.

 

 

 

 

 

 

The projector is operating normally.

 

 

 

 

 

 

The projector is in the Power management mode.

 

 

 

 

 

 

 

The temperature inside the projector is abnormally high. The projector

 

 

 

cannot be turned on. When the projector is cooled down enough and

 

 

the temperature returns to normal, the POWER indicator lights red

 

 

and the projector can be turned on. (The WARNING indicator keeps

 

 

 

 

 

 

blinking.) Check and clean the air filters.

 

 

 

 

 

 

 

The projector has been cooled down enough and the temperature

 

 

returns to normal. When turning on the projector, the WARNING

 

 

indicator stops blinking. Check and clean the air filters.

 

 

 

The projector detects an abnormal condition and cannot be turned on.

Unplug the AC power cord and plug it again to turn on the projector. If

the projector is turned off again, unplug the AC power cord and contact the dealer or the service center for service and checkup. Do not leave the projector on. It may cause an electric shock or a fire hazard.

• • • green.

• • • red

• • • off

• • • blinks green.

• • • blinks red.

 

When the projection lamp reaches the end of its life, the LAMP REPLACE indicator lights yellow. When this indicator lights yellow, replace the projection lamp with a new one promptly. Reset the lamp replacement counter after replacing the lamp. See pages 54-55.

61

Image 61
Contents Network Supported Model PLC-WXE46Note Features and DesignTable of Contents To the Owner Safety PrecautionSafety Instructions Installing the Projector in Proper Position Safety Instructions Air CirculationMoving the Projector Compliance AC Power Cord RequirementFederal Communications Commission Notice ④ Exhaust Vents Part Names and Functions③ LAN Connection Terminal Part Names and Functions Rear TerminalPart Names and Functions Top Control Part Names and Functions Remote Control Operating Range Part Names and Functions Remote Control Battery InstallationAdjustable Feet InstallationPositioning the Projector Cables used for connection Installation Connecting to a ComputerAudio Video Installation Connecting to Video EquipmentInstallation Connecting to Component Video Equipment Projector side AC outlet side Installation Connecting the AC Power CordBasic Operation What is PIN code?Turning On the Projector Enter a PIN codeBasic Operation Turning Off the Projector Top Control Menu button Point buttons Basic Operation How to Operate the On-Screen MenuFor computer source Basic Operation Menu BarFor video source Remote Control Basic Operation Focus AdjustmentKeystone Correction Top ControlRemote Control Operation Basic Operation Sound AdjustmentCOMPUTER/VIDEO button Freeze buttonBasic Operation Input Source Selection Computer InputInput Menu Source Select MenuAuto Computer Input Computer System SelectionPC System Menu ModeDirect Operation Remote Control Computer Input Auto PC AdjustmentTo store the adjusted parameters PC Adjust MenuComputer Input Manual PC Adjustment Computer Input Computer Input Image Level Selection Computer Input Image Level Adjustment Normal Screen Size AdjustmentTrue FullFor zooming in and out the images Digital zoom + CustomDigital zoom Video Input Remote Control Menu OperationInput Source Selection Video, S-video Source Select Menu VideoPointer to Computer 1 and then press the Select Video or S-video Auto Video Input Video System SelectionComponent Auto AV System Menu Video or S-videoCinema Video Input Image Level SelectionColor Video Input Image Level AdjustmentTint Noise reduction Video InputProgressive Zoom Video Input Screen Size AdjustmentWide Natural wideSetting SettingLoo Loo and Loo PIN code lock settins SettinLoo select CaptureChange the Logo PIN code Enter a Logo PIN codeLogo PIN code lock Logo PIN code lock Logo PIN code lock Dialog BoxRear CeilingScreen aspect TerminalPower management Standby modeOn start Remote control To change the code for the remote controlOn start Lamp controlKey lock Security Key lock and PIN code lock settingsPIN code lock Change the PIN code Change the PIN code lock settingChange the PIN code Fan control FanLamp counter Filter counterClosed Caption Factory default Factory defaultWarnin lo Closed CaptionNote Then check the matters below Maintenance and CleaningResetting the Filter Counter Maintenance and Cleaning Cleaning the Air FiltersCleaning the Projection Lens Maintenance and Cleaning Attaching the Lens CoverCleaning the Projector Cabinet Reset the lamp replacement counter Maintenance and Cleaning Lamp ReplacementMaintenance and Cleaning Lamp Replacement Counter Lamp Handling PrecautionsAppendix TroubleshootingAppendix Projector Condition see Indicator blinks or lightsSound Appendix Menu TreeComputer Input/Video Input Computer InputSystem AutoSetting Video Input SettingProjector Condition Appendix Indicators and Projector ConditionDisplay Appendix Compatible Computer SpecificationsTechnical Specifications Accessories DimensionsOptional Parts Appendix PJ Link Notice Service Port Connector Terminal Mini DIN 8-PIN Appendix Configurations of TerminalsPIN Code Lock No Appendix PIN Code Number MemoLogo PIN Code Lock No KM5AY