Sanyo PLC-WXE46 owner manual Safety Instructions

Page 5

Safety Instructions

All the safety and operating instructions should be read before the product is operated.

Read all of the instructions given here and retain them for later use. Unplug this projector from AC power supply before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning.

Follow all warnings and instructions marked on the projector.

For added protection to the projector during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet. This will prevent damage due to lightning and power line surges.

Do not expose this unit to rain or use near water... for example,

in a wet basement, near a swimming pool, etc...

Do not use attachments not recommended by the manufacturer as they may cause hazards.

Do not place this projector on an unstable cart, stand, or table. The projector may fall, causing serious injury to a child or adult, and serious damage to the projector. Use only with a cart or stand recommended by the manufacturer, or sold with the projector. Wall or shelf mounting should follow the manufacturer's instructions, and should use a mounting kit approved by the manufacturers.

An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn.

Slots and openings in the back and bottom of the cabinet are provided for ventilation, to ensure reliable operation of the equipment and to protect it from overheating.

The openings should never be covered with cloth or other materials, and the bottom opening should not be blocked by placing the projector on a bed, sofa, rug, or other similar surface. This projector should never be placed near or over a radiator or heat register.

This projector should not be placed in a built-in installation such as a book case unless proper ventilation is provided.

Never push objects of any kind into this projector through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the projector.

Do not install the projector near the ventilation duct of air- conditioning equipment.

This projector should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supplied, consult your authorized dealer or local power company.

Do not overload wall outlets and extension cords as this can result in fire or electric shock. Do not allow anything to rest on the power cord. Do not locate this projector where the cord may be damaged by persons walking on it.

Do not attempt to service this projector yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

Unplug this projector from wall outlet and refer servicing to qualified service personnel under the following conditions:

a. When the power cord or plug is damaged or frayed. b. If liquid has been spilled into the projector.

c. If the projector has been exposed to rain or water.

d. If the projector does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the projector to normal operation.

e. If the projector has been dropped or the cabinet has been damaged.

f. When the projector exhibits a distinct change in performance this indicates a need for service.

When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or injury to persons.

Upon completion of any service or repairs to this projector, ask the service technician to perform routine safety checks to determine that the projector is in safe operating condition.

NOTE FOR CUSTOMERS IN THE US

Hg LAMP(S) INSIDE THIS PRODUCT CONTAIN MERCURY AND MUST BE RECYCLED OR DISPOSED OF ACCORDING TO LOCAL, STATE OR FEDERAL LAWS.

Image 5
Contents Network Supported Model PLC-WXE46Note Features and DesignTable of Contents To the Owner Safety PrecautionSafety Instructions Moving the Projector Safety Instructions Air CirculationInstalling the Projector in Proper Position Federal Communications Commission Notice AC Power Cord RequirementCompliance ④ Exhaust Vents Part Names and Functions③ LAN Connection Terminal Part Names and Functions Rear TerminalPart Names and Functions Top Control Part Names and Functions Remote Control Operating Range Part Names and Functions Remote Control Battery InstallationPositioning the Projector InstallationAdjustable Feet Cables used for connection Installation Connecting to a ComputerAudio Video Installation Connecting to Video EquipmentInstallation Connecting to Component Video Equipment Projector side AC outlet side Installation Connecting the AC Power CordBasic Operation What is PIN code?Turning On the Projector Enter a PIN codeBasic Operation Turning Off the Projector Top Control Menu button Point buttons Basic Operation How to Operate the On-Screen MenuFor video source Basic Operation Menu BarFor computer source Remote Control Basic Operation Focus AdjustmentKeystone Correction Top ControlRemote Control Operation Basic Operation Sound AdjustmentCOMPUTER/VIDEO button Freeze buttonBasic Operation Input Source Selection Computer InputInput Menu Source Select MenuAuto Computer Input Computer System SelectionPC System Menu ModeDirect Operation Remote Control Computer Input Auto PC AdjustmentTo store the adjusted parameters PC Adjust MenuComputer Input Manual PC Adjustment Computer Input Computer Input Image Level Selection Computer Input Image Level Adjustment Normal Screen Size AdjustmentTrue FullDigital zoom CustomFor zooming in and out the images Digital zoom + Video Input Remote Control Menu OperationInput Source Selection Video, S-video Source Select Menu VideoPointer to Computer 1 and then press the Select Video or S-video Auto Video Input Video System SelectionComponent Auto AV System Menu Video or S-videoCinema Video Input Image Level SelectionTint Video Input Image Level AdjustmentColor Progressive Video InputNoise reduction Zoom Video Input Screen Size AdjustmentWide Natural wideSetting SettingLoo Loo and Loo PIN code lock settins SettinLoo select CaptureChange the Logo PIN code Enter a Logo PIN codeLogo PIN code lock Logo PIN code lock Logo PIN code lock Dialog BoxRear CeilingScreen aspect TerminalPower management Standby modeOn start Remote control To change the code for the remote controlOn start Lamp controlPIN code lock Security Key lock and PIN code lock settingsKey lock Change the PIN code Change the PIN code lock settingChange the PIN code Fan control FanLamp counter Filter counterClosed Caption Factory default Factory defaultWarnin lo Closed CaptionNote Then check the matters below Maintenance and CleaningResetting the Filter Counter Maintenance and Cleaning Cleaning the Air FiltersCleaning the Projector Cabinet Maintenance and Cleaning Attaching the Lens CoverCleaning the Projection Lens Reset the lamp replacement counter Maintenance and Cleaning Lamp ReplacementMaintenance and Cleaning Lamp Replacement Counter Lamp Handling PrecautionsAppendix TroubleshootingAppendix Projector Condition see Indicator blinks or lightsSound Appendix Menu TreeComputer Input/Video Input Computer InputSystem AutoSetting Video Input SettingProjector Condition Appendix Indicators and Projector ConditionDisplay Appendix Compatible Computer SpecificationsTechnical Specifications Optional Parts DimensionsAccessories Appendix PJ Link Notice Service Port Connector Terminal Mini DIN 8-PIN Appendix Configurations of TerminalsLogo PIN Code Lock No Appendix PIN Code Number MemoPIN Code Lock No KM5AY