Sanyo PLC-WXE46 owner manual Standby mode, Power management

Page 45

Setting

Standby mode

This function is available when operating the projector via network.

Normal........ Supply the power to the network function even

after turning off the projector You can turn on/ off the projector via network, modify network environment, and receive an e-mail about projector status while the projector is powered off.

Eco............. Select “Eco” when you do not use the projector

via network. The projector’s network function will stop when turning off the projector.

Refer to the owner’s manual “Network Set-up and Operation”.

Note:

When selecting Normal, the cooling fans may be running depending on the temperature inside the projector even if the projector is turned off.

Power management

For reducing power consumption as well as maintaining the lamp life, the Power management function turns off the projection lamp when the input signal is interrupted and no button is pressed for a certain period.

When the input signal is interrupted and no button is pressed for more than 30 seconds, the timer display with “No signal” appears. The countdown starts to turn off the lamp.

Select one of the operations.

Ready………When the lamp has been fully cooled

down, the POWER indicator changes to green blinking. In this condition, the projection lamp is turned on if the input signal is reconnected or any button on the remote control is pressed.

Shut down…When the lamp has been fully cooled down, the power is turned off.

Off………… Power management function is off.

Then set the countdown timer with the Point ◄► buttons.

Note:

Factory default is “Ready: 5 min.”

Power management

Time left before Lamp is off.

Press the SELECT button at Power management and this box appears. Select one of three settings with the Point ◄► buttons, and go to the timer with the Point ▲▼ buttons and set time with the Point ◄► buttons.

45

Image 45
Contents Network Supported Model PLC-WXE46Note Features and DesignTable of Contents To the Owner Safety PrecautionSafety Instructions Safety Instructions Air Circulation Installing the Projector in Proper PositionMoving the Projector AC Power Cord Requirement ComplianceFederal Communications Commission Notice ④ Exhaust Vents Part Names and Functions③ LAN Connection Terminal Part Names and Functions Rear TerminalPart Names and Functions Top Control Part Names and Functions Remote Control Operating Range Part Names and Functions Remote Control Battery InstallationInstallation Adjustable FeetPositioning the Projector Cables used for connection Installation Connecting to a ComputerAudio Video Installation Connecting to Video EquipmentInstallation Connecting to Component Video Equipment Projector side AC outlet side Installation Connecting the AC Power CordBasic Operation What is PIN code?Turning On the Projector Enter a PIN codeBasic Operation Turning Off the Projector Top Control Menu button Point buttons Basic Operation How to Operate the On-Screen MenuBasic Operation Menu Bar For computer sourceFor video source Remote Control Basic Operation Focus AdjustmentKeystone Correction Top ControlRemote Control Operation Basic Operation Sound AdjustmentCOMPUTER/VIDEO button Freeze buttonBasic Operation Input Source Selection Computer InputInput Menu Source Select MenuAuto Computer Input Computer System SelectionPC System Menu ModeDirect Operation Remote Control Computer Input Auto PC AdjustmentTo store the adjusted parameters PC Adjust MenuComputer Input Manual PC Adjustment Computer Input Computer Input Image Level Selection Computer Input Image Level Adjustment Normal Screen Size AdjustmentTrue FullCustom For zooming in and out the images Digital zoom +Digital zoom Video Input Remote Control Menu OperationInput Source Selection Video, S-video Source Select Menu VideoPointer to Computer 1 and then press the Select Video or S-video Auto Video Input Video System SelectionComponent Auto AV System Menu Video or S-videoCinema Video Input Image Level SelectionVideo Input Image Level Adjustment ColorTint Video Input Noise reductionProgressive Zoom Video Input Screen Size AdjustmentWide Natural wideSetting SettingLoo Loo and Loo PIN code lock settins SettinLoo select CaptureChange the Logo PIN code Enter a Logo PIN codeLogo PIN code lock Logo PIN code lock Logo PIN code lock Dialog BoxRear CeilingScreen aspect TerminalPower management Standby modeOn start Remote control To change the code for the remote controlOn start Lamp controlSecurity Key lock and PIN code lock settings Key lockPIN code lock Change the PIN code lock setting Change the PIN codeChange the PIN code Fan control FanLamp counter Filter counterClosed Caption Factory default Factory defaultWarnin lo Closed CaptionNote Then check the matters below Maintenance and CleaningResetting the Filter Counter Maintenance and Cleaning Cleaning the Air FiltersMaintenance and Cleaning Attaching the Lens Cover Cleaning the Projection LensCleaning the Projector Cabinet Reset the lamp replacement counter Maintenance and Cleaning Lamp ReplacementMaintenance and Cleaning Lamp Replacement Counter Lamp Handling PrecautionsAppendix TroubleshootingAppendix Projector Condition see Indicator blinks or lightsSound Appendix Menu TreeComputer Input/Video Input Computer InputSystem AutoSetting Video Input SettingProjector Condition Appendix Indicators and Projector ConditionDisplay Appendix Compatible Computer SpecificationsTechnical Specifications Dimensions AccessoriesOptional Parts Appendix PJ Link Notice Service Port Connector Terminal Mini DIN 8-PIN Appendix Configurations of TerminalsAppendix PIN Code Number Memo PIN Code Lock NoLogo PIN Code Lock No KM5AY