Hitachi CP-S210F, CP-S210T user manual Lamp

Page 32

Lamp

WARNING

HIGH VOLTAGE HIGH TEMPERATURE HIGH PRESSURE

The projector uses a high-pressure mercury glass lamp. The lamp can break with a loud bang, or burn out, if jolted or scratched, handled while hot, or worn over time. Note that each lamp has a different lifetime, and some may burst or burn out soon after you start using them. In addition, when the bulb bursts, it is possible for shards of glass to fly into the lamp housing, and for gas containing mercury to escape from the projector’s vent holes.

If the lamp should break (it will make a loud bang when it does), unplug the power cord from the outlet, and make sure to request a replacement lamp from your local dealer. Note that shards of glass could damage the projector’s internals, or cause injury during handling, so please do not try to clean the projector or replace the lamp yourself.

If the lamp should break (it will make a loud bang when it does), ventilate the room well, and make sure not to breathe the gas that comes out of the projector vents, or get it in your eyes or mouth.

Do not open the lamp cover while the projector is suspended from above. This is dangerous, since if the lamp’s bulb has broken, the shards will fall out when the cover is opened. In addition, working in high places is dangerous, so ask your local dealer to have the lamp replaced even if the bulb is not broken

If the indicators or a message prompts you to replace the lamp (see the section

“Related Messages” and “Regarding the indicator Lamps”), replace the lamp as soon as possible. Using the lamp for long periods of time, or past the replacement date, could cause it to burst. Do not use old (used) lamps; this is a cause of breakage.

If the lamp breaks soon after the first time it is used, it is possible that there are electrical problems elsewhere besides the lamp. If this happens, contact your local dealer or a service representative.

Use the lamp of the specified type only.Type number: DT00581 (sold separately)

Handle with care: jolting or scratching could cause the lamp bulb to burst during use.

Before replacing the lamp, make sure the power switch is off and the power cable is not plugged in, then wait at least 45 minutes for the lamp to cool sufficiently. Handling the lamp while hot can cause burns, as well as damaging the lamp.

Do not use the projector with the lamp cover removed. At the lamp replacing, make sure that the screws are screwed in firmly. Loose screws could result in damage or injury.

Obey local ordinances when disposing of used lamps. In most cases, it is possible to dispose of used bulbs in the same manner as used glass bottles, but in some cases, bulbs are sorted separately.

32

Image 32
Contents Projector CP-S210W/CP-S210WT/CP-S210WFContents Projector Features PreparationPart Names Fastening The Lens CapInput button Power indicator Temp indicator ProjectorRemote Control Setting Up ArrangementAdjusting The Projectors Elevator Adjust the height of the projector byAs necessary, you can also finely Twisting the elevator feet by handConnecting Your Devices AUDIO-L AUDIO-R ScartConnecting Power Supply Firmly plug the power cord’s plug 1 into the outletRemote Control Remove Battery coverClose Battery cover Putting BatteriesOperating The Remote Control Power ON/OFF Turning On The PowerWhen the lens cap is attached, remove Set the power switch to onSelecting An Input Signal Attached the lens cap Turning Off The PowerSwitch the power switch to O OFF Temporarily Muting The Sound Adjusting The VolumeOperating Press the Position button Adjusting The PositionUse Buttons to adjust Position Using The Automatic Adjustment Feature Correcting Keystone DistortionsUsing The Magnify Feature Use Buttons to adjust the zoom LevelFreezing The Screen Press the Magnify on buttonTemporarily Blanking The Screen Signal SearchingSelecting The Aspect Ratio Multifunctional Settings Using The Menu FunctionsMain Menu Picture 1 Menu Load/Save a Setting Reset the PICTURE-1 Menu ItemsPicture 1 Menu MY MemoryPhase Picture 2 MenuPosition SizeInput Menu VideoFrame Lock 3D-YCSInput Menu Video NRInformation S2-ASPECTSearch AdjustAuto Menu Message Screen MenuStart UP Lamp Time Option MenuScreen Type Lamp Replacing The Lamp Air Filter Caring For The Air FilterReplacing The Air Filter New air filter. Tell the dealer your airHold the release buttons of the air Filter, while pulling down itCaring For The Cabinet And Remote Control Other CareCaring For The Inside Of The Projector Caring For The LensTroubleshooting Related MessagesRelated Messages Regarding The Indicator Lamps Power Lamp TempRegarding The Indicator Lamps IndicatorPhenomena That May Easily Be Mistaken For Machine Defects Warranty And After-Service Phenomena That May Easily Be Mistaken For Machine DefectsSpecifications SpecificationRGB Input Ports Audio Ports Video Input PortsTechnical Signal Connectors TechnicalExample Of Computer Signal Resolution FH kHz FV Hz Rating Signal mode DisplayVesa Text VesaInitial Set Signals Mac 13modeRS-232C Communication Connecting The CableCommunications Setting Requesting projector status Get command Changing the projector settings Set commandUsing the projector default settings Reset Command Increasing the projector setting value Increment commandCommand Data Chart 4A D2日本語 Be EF FE D7 Be EF EC D9 Auto RGB Middle Be EF High Turn on Be EF