Hitachi CP-S210F, CP-S210T user manual Projector, Input button Power indicator Temp indicator

Page 5

Part Names (continued)

The Projector (continued)

INPUT button 15			POWER indicator 14	39 TEMP indicator
toggles between the signal			tells the state of power	lights or blinks when any
ports.			supply. Refer to the section	problem about internal
RGB		VIDEO	“Power ON/OFF”.	temperature has happened.

S-VIDEO

COMPONENT VIDEO

	STANDBY/ON 14	POWER
	button	POWER
	button
	prepares for turning the
	power on/off. Refer to the	INPUT
	STANDBY/ON	INPUT

section “Power ON/OFF”.

AUDIO		R port 10

L port 10

(from a video equipment)

AUDIO port 10

(from a computer)

S-VIDEO port 10

VIDEO port 10

COMPONENT VIDEO - Y 10

COMPONENT VIDEO - CB/PB 10

COMPONENT VIDEO - CR/PR 10

TEMP

MENU

11

39LAMP indicator lights or blinks when any problem about the lamp has

LAMP happened.

22MENU buttons operate the menu function.

10CONTROL port

10RGB port

14Power switch AC inlet

Projector (Rear/Left)

5

Image 5

Contents CP-S210W/CP-S210WT/CP-S210WF ProjectorContents Preparation Projector FeaturesFastening The Lens Cap Part NamesProjector Input button Power indicator Temp indicatorRemote Control Arrangement Setting UpAdjust the height of the projector by Adjusting The Projectors ElevatorAs necessary, you can also finely Twisting the elevator feet by handConnecting Your Devices AUDIO-R Scart AUDIO-LFirmly plug the power cord’s plug 1 into the outlet Connecting Power SupplyRemove Battery cover Remote ControlClose Battery cover Putting BatteriesOperating The Remote Control Turning On The Power Power ON/OFFWhen the lens cap is attached, remove Set the power switch to onSelecting An Input Signal Attached the lens cap Turning Off The PowerSwitch the power switch to O OFF Temporarily Muting The Sound Adjusting The VolumeOperating Press the Position button Adjusting The PositionUse Buttons to adjust Position Correcting Keystone Distortions Using The Automatic Adjustment FeatureUse Buttons to adjust the zoom Level Using The Magnify FeatureFreezing The Screen Press the Magnify on buttonTemporarily Blanking The Screen Signal SearchingSelecting The Aspect Ratio Using The Menu Functions Multifunctional SettingsMain Menu Picture 1 Menu Reset the PICTURE-1 Menu Items Load/Save a SettingPicture 1 Menu MY MemoryPicture 2 Menu PhasePosition SizeVideo Input MenuFrame Lock 3D-YCSVideo NR Input MenuInformation S2-ASPECTSearch AdjustAuto Menu Message Screen MenuStart UP Lamp Time Option MenuScreen Type Lamp Replacing The Lamp Caring For The Air Filter Air FilterNew air filter. Tell the dealer your air Replacing The Air FilterHold the release buttons of the air Filter, while pulling down itOther Care Caring For The Cabinet And Remote ControlCaring For The Inside Of The Projector Caring For The LensRelated Messages TroubleshootingRelated Messages Power Lamp Temp Regarding The Indicator LampsIndicator Regarding The Indicator LampsPhenomena That May Easily Be Mistaken For Machine Defects Phenomena That May Easily Be Mistaken For Machine Defects Warranty And After-ServiceSpecification SpecificationsRGB Input Ports Audio Ports Video Input PortsTechnical Technical Signal ConnectorsResolution FH kHz FV Hz Rating Signal mode Display Example Of Computer SignalVesa Text VesaMac 13mode Initial Set SignalsRS-232C Communication Connecting The CableCommunications Setting Changing the projector settings Set command Requesting projector status Get commandUsing the projector default settings Reset Command Increasing the projector setting value Increment command4A D2 Command Data Chart日本語 Be EF FE D7 Be EF EC D9 Auto RGB Middle Be EF High Turn on Be EF