Hitachi CP-S210T, CP-S210F user manual Connecting Your Devices

Page 9

Setting Up (continued)

Connecting Your Devices

WARNING • Incorrect connecting could result in fire or electrical shock. Whenever attempting to connect other devices to the projector, please thoroughly read the "User's Manual - Safety Guide", this manual and the manual of each device to be connected.

CAUTION • TURN OFF ALL DEVICES prior to connecting them to the projector. Attempting to connect a live device to the projector may generate extremely loud noises or other abnormalities that may result in malfunction and/or damage to the device and/or projector.

ATTENTION • Make sure that you connect devices to the correct port. Incorrect connection may result in malfunction and/or damage to the device and/or projector. Refer to the section “TECHNICAL” of this manual for the pin assignment of connectors and RS-232C communication data.

Some cables have to be used with core set. Use the accessory cable or a designated-type cable for the connection. For cables that have a core only at one end, connect the core to the projector.

Secure the screws on the connectors and tighten.

Whenever attempting to connect a laptop computer to the projector, be sure to activate the laptop’s RGB external image output (set the laptop to CRT display or to simultaneous LCD and CRT display). For details on how this is done, please refer to the instruction manual of the corresponding laptop computer.

NOTE About Plug-and-Play Capability

This projector is compatible with VESA DDC 1/2B. Plug-and-Play can be achieved by connecting this projector to computers that are VESA DDC (display data channel) compatible. Please take advantage of this function by connecting the accessory RGB cable to the RGB port (DDC 1/2B compatible). Plug-and-Play may not work properly if any other type of connection is attempted.

Plug-and-Play is a system composed of the computer, its operating system and peripheral equipment (i.e. display devices).

Please use the standard drivers in your computer as this projector is a Plug-and-Play monitor.

NOTE • Some computers may have multiple display screen modes. Use of some of these modes will not be possible with this projector.

For some RGB input modes, the optional Mac adapter is necessary.

When the image resolution is changed on a computer, depending on an input, automatic adjust function may take some time and may not be completed. In this case, you may not be able to see a check box to select “Yes/No” for the new resolution on Windows. Then the resolution will go back to the original. It might be recommended to use other CRT or TFT monitors to change the resolution.

9

Image 9
Contents CP-S210W/CP-S210WT/CP-S210WF ProjectorContents Preparation Projector FeaturesFastening The Lens Cap Part NamesProjector Input button Power indicator Temp indicatorRemote Control Arrangement Setting UpAdjust the height of the projector by Adjusting The Projectors ElevatorAs necessary, you can also finely Twisting the elevator feet by handConnecting Your Devices AUDIO-R Scart AUDIO-LFirmly plug the power cord’s plug 1 into the outlet Connecting Power SupplyRemove Battery cover Remote ControlClose Battery cover Putting BatteriesOperating The Remote Control Turning On The Power Power ON/OFFWhen the lens cap is attached, remove Set the power switch to onSelecting An Input Signal Turning Off The Power Switch the power switch to O OFFAttached the lens cap Adjusting The Volume OperatingTemporarily Muting The Sound Adjusting The Position Use Buttons to adjust PositionPress the Position button Correcting Keystone Distortions Using The Automatic Adjustment FeatureUse Buttons to adjust the zoom Level Using The Magnify FeatureFreezing The Screen Press the Magnify on buttonSignal Searching Selecting The Aspect RatioTemporarily Blanking The Screen Using The Menu Functions Multifunctional SettingsMain Menu Picture 1 Menu Reset the PICTURE-1 Menu Items Load/Save a SettingPicture 1 Menu MY MemoryPicture 2 Menu PhasePosition SizeVideo Input MenuFrame Lock 3D-YCSVideo NR Input MenuInformation S2-ASPECTAdjust Auto MenuSearch Screen Menu Start UPMessage Option Menu Screen TypeLamp Time Lamp Replacing The Lamp Caring For The Air Filter Air FilterNew air filter. Tell the dealer your air Replacing The Air FilterHold the release buttons of the air Filter, while pulling down itOther Care Caring For The Cabinet And Remote ControlCaring For The Inside Of The Projector Caring For The LensRelated Messages TroubleshootingRelated Messages Power Lamp Temp Regarding The Indicator LampsIndicator Regarding The Indicator LampsPhenomena That May Easily Be Mistaken For Machine Defects Phenomena That May Easily Be Mistaken For Machine Defects Warranty And After-ServiceSpecification SpecificationsRGB Input Ports Audio Ports Video Input PortsTechnical Technical Signal ConnectorsResolution FH kHz FV Hz Rating Signal mode Display Example Of Computer SignalVesa Text VesaMac 13mode Initial Set SignalsConnecting The Cable Communications SettingRS-232C Communication Changing the projector settings Set command Requesting projector status Get commandUsing the projector default settings Reset Command Increasing the projector setting value Increment command4A D2 Command Data Chart日本語 Be EF FE D7 Be EF EC D9 Auto RGB Middle Be EF High Turn on Be EF