Hitachi CP-S860W user manual When you think something wrong, Indicators

Page 33

Message table (continued)

Indicators

The ON indicator, LAMP indicator and TEMP indicator light or blink in the following cases.

ON

LAMP

TEMP

Message

 

Processing

indicator

indicator

indicator

 

 

 

 

 

 

 

 

 

 

 

 

Lights orange

Turns off

Turns off

Standby status

 

 

 

 

 

 

 

 

 

 

 

 

 

Flashes green

Turns off

Turns off

Warming up

 

 

 

 

 

 

 

 

 

 

 

 

 

Lights green

Turns off

Turns off

Operation status *1

 

 

 

 

 

 

Flashes orange

Turns off

Turns off

Cool down

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Wait some time (approx. 20 min.) before

Lights red

Lights red

Turns off

The lamp does not light. *2

turning the power on again. If the

 

 

 

 

indicator still lights, the lamp may have

 

 

 

 

failed and. Replace with a new lamp.

 

 

 

 

 

 

 

Lights red

Flashes red

Turns off

A lamp has not been inserted

Firmly insert the lamp as far as possible

or the lamp cover is missing.

and screw the lamp cover in place.

 

 

 

 

 

 

 

 

 

 

Lights red

Turns off

Flashes red

The cooling fan is not operating.

Contact your dealer.

 

 

 

 

 

 

 

Flashes red

Flashes red

Turns off

The total lamp time has

Contact your dealer.

exceeded the replacement time.

When the LAMP or TEMP indicator lights or flashes, turn off the MAIN POWER switch before proceeding. If the problem still persists, contact your dealer or service company.

*1: When the cooling fan is stopped and the interior becomes overheated, the power will turn off automatically to allow cooling (the indicator will turn off). In such cases, turn off the projector power, allow the set to cool and then turn the projector power on again. The lamp will then light. If the lamp does not light, contact your dealer or service company.

*2: In some cases, when the air holes becomes blocked and the interior temperature rises, the lamp will be turned off for protection and the LAMP indicator will flash red. In such cases, turn off the MAIN POWER switch, allow the set to cool (for approx. 20 min.) and then turn the power on again.

When you think something wrong

Before requesting repair, check in accordance with the following chart. If the situation cannot be corrected, then contact your dealer.

Symptom

Possible cause

 

Remedy

Page

 

 

 

 

The power is not

•The main power switch is not turned on.

•Turn on the main power switch.

P.13

turned on.

•The power cord is disconnected.

•Plug the power cord into an AC power outlet.

P.9

 

 

 

 

No video or audio.

•The input is not correctly set.

•Use the projector or remote control to set.

P.8,10,

 

 

 

 

13,19

 

•No signal input.

•Connect correctly.

P.9,31

Video is present but

•The projector is not correctly connected.

•Connect correctly.

P.9,31

no audio.

•The volume is seet to minimum.

•Press VOLUME + on the remote control or display

P.10,18

 

 

the menu screen and adjust the volume.

 

 

•Mute is turned on.

•Press the MUTE button.

P.8,10

Audio is present but

•The projector is not correctly connected.

•Connect correctly.

P.9,31

no video.

•The brightness adjustment knob is rotated

•Select BRIGHT with the MENU button and then

P.17

 

fully clockwise.

press the (

) key.

 

 

•The lens cap is still on.

•Remove the lens cap.

P.13

 

 

 

 

 

Colors are pale and

Color density and color matching are not

Adjust the video.

P.18

color matching is poor.

correctly adjusted.

 

 

 

 

 

 

 

Images are dark.

•Brightness and contrast are not correctly

•Adjust the video.

P.18

 

adjusted.

 

 

 

 

•The lamp is nearing the end of its service life.

•Replace with a new lamp.

P.32

Video is blurred.

Focus or H PHASE is out of adjustment.

Adjust the focus or H PHASE.

P.13,18

 

 

 

 

The LAMP indicator

Lamp failure.

Wait approximately 20 min. and then turn the

P.33

lights red.

 

power on again.

 

The TEMP indicator

Internal overheating.

•Make sure the ventilation openings are not blocked.

P.31,32

lights red.

 

•Clean the air filter.

 

 

 

•Lower the ambient temperature to 35 degrees C or less.

 

 

 

 

 

 

A bright dot may be seen in the picture. This is a phenomenon peculiar to the liquid crystal and is not a problem.

33

Page 32 Page 34
Image 33
Page 32 Page 34
Contents Features ContentsPageOutline Page Before Use Do not install on an unstable surface If a problem should occurDo not look through the lens when the lamp is on Use only the indicated power supplyHandle the power cord with care Do not position the powerDo not allow the laser beam to enter the eyes Battery usage Care and maintenanceClean the projector interior once every two years Avoid installation in humid or dusty locationsAvoid excessively hot locations Sound volumeLens care Cabinet careNames and functions of each part Checking the package ContentsAC in jack Main power switchVideo in jack RGB in jackDisk PAD Remote control transmitter3Close the battery cover 1Remove the battery cover2Loading the batteries Make sure the plus and minus poles are correctly orientedTypical LCD Projector and Screen Installation InstallationUsing the adjusters Top view Side viewTo project Basic operationsTurn off the main power switch of the projector OFF Turning off the powerPlug & Play Press the STANDBY/ON button for approximately 1 secFreeze function will be cancelled Cancelling the Freeze functionFreeze function Press the Freeze buttonChanging the magnification ratio Magnify functionMoving the display area Returning to normal displayReturning to the initial settings Adjustments and functionsPress the Menu Menu screen will appear. refer to page 18-21 for detailsUsing the Setup Menu RGB InputBlank KeystoneTimer Communication functions, etc., can be set from the OPT menuLanguage Connection to the RGB signal terminal Connection to the video signal terminalsInput signals Signal input jacksExample of computer signal Connection to the RGB signal terminalInitial set signals Connection to the RGB signal terminalConnecting the USB Mouse functions Connection to the control signal terminalControl signal jack ADB Mac mouseSerial mouse RS232C communication System Video Command data chartRequesting projector status Cleaning the Air filter Example of system setupPull out the power cord Remove the front air filter Clean the air filter about every 100 hoursInstalling the air filter Cleaning the air filter with a vacuum cleanerLamp Message tableIndicators When you think something wrongDimensional Diagram Specifications· These specifications are subject to change without notice Cannot be used in any other countryAbout the warranty and after-service About the warrantyRepairs after the warranty period has elapsed QR41821 Merkmale KurzbeschreibungInhaltSeite ModellPage Warnung Vorsicht Vor der InbetriebnahmeNicht auf unstabilen Flächen aufstellen Bei Auftreten von BetriebsstörungenNiemals das Gehäuse öffnen Nicht modifizierenDas Netzkabel vorsichtig handhaben Nur mit der korrekten Netzspannung betreibenKann zu Bränden oder elektrischen Schlägen führen Betreiben Sie den Projektor ausschließlichWartung und Pflege Die Belüftungsöffnungen nicht blockierenBatteriebetrieb Den Projektor alle zwei Jahre innen säubern lassenTransport des Projektors Wenn der Projektor längere Zeit nicht benutzt wirdÜbermäßig heiße Plätze vermeiden LautstärkeÜberprüfung des Lieferumfangs Bezeichnung und Funktion der TeileProjektor Vorsicht Anschluß an die Netzeingangsbuchse AC Mouse RESET/RIGHT FernbedienungsteilMagnify 1Den Batteriefachdeckel 2Einlegen der Batterien Abnehmen Vorsicht Vorsichtsmaßregeln für den Batteriebetrieb3Den Batteriefachdeckel wieder anbringen Typische Aufstellung von LCD-Projektor und Leinwand AufstellungVerwendung der Fußversteller AufsichtProjizieren von Bildern Grundlegende BedienungDie Taste Standby / on drücken Das angeschlossene Gerät einschaltenAusschalten der Netzversorgung Grundlegende Bedienung FortsetzungFesthalten-Funktion Aufheben der FREEZE-FunktionDie FREEZE-Funktion wird aufgehoben Ändern des Vergrößerungsverhältnisses VergrößerungsfunktionVerschieben des Anzeigebereichs Zurückstellen auf normale AnzeigeRückstellung auf die Anfangseinstellungen Einstellungen und FunktionenDas Menübild erscheint Einzelheiten siehe Seite Der gewählte Menügegenstand erscheint jetzt grünEinstellungen und Funktionen Fortsetzung Verwendung des Einrichten-Menüs SetupFH horizontale Sync-Frequenz Trapez StartenBILD-IN-BILD Sprache AUTOM-AUSSync EIN G Signaleingänge EingangssignaleAnschluß an die Video-Eingangsbuchsen Anschluß an die RGB-BuchseAnschluß an die RGB-Buchse Fortsetzung Beispiel eines ComputersignalsComputer/Signal Horizontale Signalsteuerung µs AnfangseinstellungssignaleAnschluß der USB-Maus Anschluß an die Steuersignalbuchse MausfunktionenDurchlesen Steuersignalbuchse Control ADB-Maus MacSerienmaus RS232C-Datenaustausch Anschluß an die Steuersignalbuchse FortsetzungBefehlsdatentabelle Wenn in Datenübertragungsblockfehler auftritt Reinigen des Luftfilters Systemübersicht BeispielDen Luftfilter etwa alle 100 Betriebsstunden säubern Filter Modell LuftfilterLampe Reinigen des Luftfilters FortsetzungMeldungstabelle BildschirmanzeigenAbhilfe bei Problemen Meldungstabelle FortsetzungAnzeigen Abmessungsdiagramm Nicht in anderen Ländern verwendet werdenEinheit mm Zur Garantie Garantie und KundendienstZum Kundendienst Reparaturen während der GarantiezeitQR41821

CP-S860W specifications

The Hitachi CP-S860W is a high-performance projector designed to deliver exceptional image quality, making it an ideal choice for a variety of settings, including classrooms, corporate environments, and large venues. With its advanced features and cutting-edge technologies, the CP-S860W stands out as a reliable and versatile projection solution.

One of the key features of the Hitachi CP-S860W is its high brightness output, providing up to 6,500 lumens. This brightness capability ensures that images remain clear and vibrant even in well-lit environments, making it suitable for presentations and lectures where ambient light cannot be fully controlled. The projector's native WXGA resolution (1280 x 800 pixels) enhances image clarity, allowing for detailed visuals that are essential for displaying graphs, charts, and other data-heavy content.

The CP-S860W incorporates advanced image processing technologies, such as a built-in scaler and various color enhancement features. These technologies enable the projector to deliver a rich color palette and sharp detail, ensuring that images maintain fidelity and color accuracy. Additionally, it supports multiple resolutions, allowing users to project content from various devices without loss in quality.

Another notable characteristic of the CP-S860W is its versatile connectivity options. The projector is equipped with multiple HDMI ports, RGB inputs, and composite video connections, making it compatible with a wide range of devices, including laptops, DVD players, and gaming consoles. Its compatibility with wireless presentation systems also allows for hassle-free connections, enabling users to present without being tethered by cables.

The projector features a long lamp life of up to 5,000 hours in standard mode and up to 10,000 hours in eco mode. This longevity minimizes maintenance needs and reduces total cost of ownership, making it a cost-effective investment. Moreover, its eco-friendly features, including energy-saving modes, contribute to lower power consumption, aligning with sustainable practices.

With a weight of approximately 11.5 pounds, the Hitachi CP-S860W is portable enough for easy transportation between locations, while robust enough for permanent installation. Its user-friendly interface and intuitive remote control facilitate seamless operation, ensuring an efficient setup process for any presentation.

In summary, the Hitachi CP-S860W projector combines high brightness, versatile connectivity, and advanced image processing technologies, making it a powerful tool for delivering engaging and impactful visual presentations in any environment.
Top Page Image Contents